Fisher & Paykel EB60DSXB2 Operating instructions

Displayed Messages
Displayed Message
Possible
Cause What To Do
FILL TANK WITH FRESH WATER
Insufficient
water in the
tank.
Fill the tank with water and ensure that it is inserted
correctly, pushing it as far as it will go until it clicks
into place.
INSERT WATER TANK
The tank is
not correctly
in place.
Insert the tank correctly and press as far as it will
go.
https://producthelp.fisherpaykel.com/au/Cook/Companion_Products/Built-in_Coffee_Maker/EB60DSXB2/User_Guide_EB60D…
Updated: Thu, 02 Mar 2023 01:57:04 GMT
Powered by
1

Displayed Message
Possible
Cause What To Do
EMPTY GROUNDS CONTAINER
The grounds
container is
full.
Empty the grounds container and drip tray, clean
and place it back in the appliance.
When removing the drip
tray, the grounds
container must be
emptied, even if it
contains few grounds. If
this is not done, when
you make the next
drinks, the grounds
container may fill up
more than expected and
clog the machine.
INSERT GROUNDS CONTAINER AND
DRIP TRAY
After
cleaning, the
grounds
container
has not been
re-inserted.
Remove the drip tray and insert the grounds
container.
ADD PRE-GROUND COFFEE, COFFEE
MAX. 1 MEASURE
The ‘pre-
ground
coffee’
function has
been
selected
without
placing any
pre-ground
coffee in the
funnel.
Place pre-ground coffee in the funnel and repeat
delivery
The pre-
ground
coffee funnel
Empty the funnel as described in section ‘Cleaning
the pre-ground coffee funnel.’
https://producthelp.fisherpaykel.com/au/Cook/Companion_Products/Built-in_Coffee_Maker/EB60DSXB2/User_Guide_EB60D…
Updated: Thu, 02 Mar 2023 01:57:04 GMT
Powered by
2

Displayed Message
Possible
Cause What To Do
is clogged.
ADD COFFEE, COFFEE MAX. 1 MEASURE
A long coffee
with pre-
ground
coffee has
been
requested.
Place pre-ground coffee in the funnel and press
to continue and complete delivery
FILL BEANS CONTAINER
The coffee
beans have
run out.
Fill the beans container.
The grinding
is too fine
and the
coffee is
delivered too
slowly or not
at all.
Repeat coffee delivery and turn the grinding
adjustment dial one click clockwise towards ‘7’ while
the coffee mill is in operation. If after making at
least two coffees, delivery is still too slow, repeat
the correction procedure, turning the grinding
adjustment dial another click until delivery is correct
(see section ‘Adjusting the coffee mill’). If the
problem persists, make sure the water tank is fully
inserted.
If you’re
using a
water
softener
filter, an air
bubble may
have been
Deliver some water through the hot water spout
until the flow becomes regular.
https://producthelp.fisherpaykel.com/au/Cook/Companion_Products/Built-in_Coffee_Maker/EB60DSXB2/User_Guide_EB60D…
Updated: Thu, 02 Mar 2023 01:57:04 GMT
Powered by
3

Displayed Message
Possible
Cause What To Do
GROUND TOO FINE. ADJUST MILL 1
CLICK WHILE IN OPERATION
released
inside the
circuit,
obstructing
delivery
SELECT A MILDER TASTE OR REDUCE
PRE-GROUND COFFEE QUANTITY
Too much
coffee has
been used.
Select a milder strength by pressing STRENGTH
or reduce the quantity of pre-ground coffee
(maximum 1 measure).
INSERT WATER SPOUT
The hot
water spout
is not
inserted or is
not inserted
correctly.
Insert the water spout as far as it will go
https://producthelp.fisherpaykel.com/au/Cook/Companion_Products/Built-in_Coffee_Maker/EB60DSXB2/User_Guide_EB60D…
Updated: Thu, 02 Mar 2023 01:57:04 GMT
Powered by
4

Displayed Message
Possible
Cause What To Do
INSERT MILK CONTAINER
The milk
container is
not inserted
correctly.
Insert the milk container as far as it will go.
INSERT INFUSER ASSEMBLY
The infuser
has not been
replaced
after
cleaning.
Insert the infuser as described in section ‘Cleaning
the infuser’.
WATER CIRCUIT EMPTY PRESS OK TO
START FILLING PROCESS
The water
circuit is
empty.
Press
to deliver water from the spout until it flows out
normally. Delivery stops automatically.
If the problem persists, make sure the water tank is
fully inserted.
https://producthelp.fisherpaykel.com/au/Cook/Companion_Products/Built-in_Coffee_Maker/EB60DSXB2/User_Guide_EB60D…
Updated: Thu, 02 Mar 2023 01:57:04 GMT
Powered by
5

Displayed Message
Possible
Cause What To Do
PRESS OK TO START CLEANING
PROCESS OR TURN MILK FROTH
ADJUSTMENT DIAL
The milk
container
has been
inserted with
the froth
adjustment
dial in the
CLEAN
position
To proceed with the CLEAN function, press
or turn the froth adjustment dial to one of the milk
positions.
TURN DIAL TO POSITION TO START
CLEANING
Milk has
been
delivered
recently and
the tubes
inside the
milk
container
must be
cleaned.
Turn the froth adjustment dial to CLEAN.
TURN THE MILK FROTH ADJUSTMENT
The milk
container
has been
inserted with
the froth
adjustment
dial in the
CLEAN
position.
Turn the dial to the required froth position
https://producthelp.fisherpaykel.com/au/Cook/Companion_Products/Built-in_Coffee_Maker/EB60DSXB2/User_Guide_EB60D…
Updated: Thu, 02 Mar 2023 01:57:04 GMT
Powered by
6

Displayed Message
Possible
Cause What To Do
DIAL TO MILK POSITION
DESCALING NEEDED PRESS OK TO
START (~45min)
The machine
must be
descaled.
Press
to start descaling or BACK to descale later. The
descaling procedure described in section ‘Descale’
needs to be performed.
REPLACE WATER FILTER PRESS OK TO
START
The water
softener filter
is
exhausted.
Press
to replace or remove the filter, or BACK to carry out
the procedure later. Follow the instructions in
section ‘Water softener filter’.
GENERAL ALARM: REFER TO USER
MANUAL
The inside of
the
appliance is
very dirty
Clean the inside of the appliance thoroughly, as
described in section ‘Cleaning’. If the message is
still displayed after cleaning, contact Customer
Care.
The
appliance
needs
descaling
and/or the
filter must be
replaced.
The descaling procedure described in the ‘Descale’
section, needs to be performed and/or the filter
needs replacing or removing as described in
section ‘Water softener filter’.
https://producthelp.fisherpaykel.com/au/Cook/Companion_Products/Built-in_Coffee_Maker/EB60DSXB2/User_Guide_EB60D…
Updated: Thu, 02 Mar 2023 01:57:04 GMT
Powered by
7

Displayed Message
Possible
Cause What To Do
The tubes
inside the
milk
container
must be
cleaned.
Turn the froth adjustment dial to CLEAN.
The filter
must be
replaced.
Replace the filter or remove it as described in
section ‘Water softener filter’
The machine
must be
descaled.
The descaling procedure described in section
‘Descale’ needs to be performed.
The auto-
start function
is enabled.
To disable the function, proceed as described in
section ‘Auto start’.
Energy
saving is
enabled.
To disable energy saving, proceed as described in
section ‘Energy saving’.
https://producthelp.fisherpaykel.com/au/Cook/Companion_Products/Built-in_Coffee_Maker/EB60DSXB2/User_Guide_EB60D…
Updated: Thu, 02 Mar 2023 01:57:04 GMT
Powered by
8