Fisher & Paykel EB60DSXBB1 User manual

Displayed Messages
Displayed Message Possible Cause What to Do
Fill Tank with Fresh Water
Insufficient water in
the tank.
Fill the tank with water and ensure that it is
inserted correctly, pushing it as far as it will go
until it clicks into place.
Insert Water Tank
The tank is
not correctly in place.
Insert the tank correctly and press as far as it
will go.
https://producthelp.fisherpaykel.com/nz/Cook/Companion_Products/Built-in_Coffee_Maker/EB60DSXBB1/Troubleshooting_a…
Updated: Wed, 12 Apr 2023 11:53:47 GMT
Powered by
1

Displayed Message Possible Cause What to Do
Empty Grounds Container
The grounds container
is full.
Empty the grounds container and drip tray,
clean and place it back in the appliance.
When removing the
drip tray, the
grounds
container must be
emptied, even if it
contains few
grounds. If this is not
done, when you
make the next
drinks, the
grounds container
may fill up more
than expected and
clog the machine.
Insert Grounds Container
After cleaning,
the grounds
container has not
been re-inserted.
Remove the drip tray and insert the grounds
container.
Add Pre-Ground Coffee, Coffee MAX. 1
Measure
The ‘pre-
ground coffee’
function has been
selected without
placing any pre-
ground coffee
in the funnel.
Place pre-ground coffee in the funnel and
repeat delivery.
The pre-ground coffee
funnel is clogged.
Empty the funnel as described in section
‘Cleaning the pre-ground coffee funnel.’
https://producthelp.fisherpaykel.com/nz/Cook/Companion_Products/Built-in_Coffee_Maker/EB60DSXBB1/Troubleshooting_a…
Updated: Wed, 12 Apr 2023 11:53:47 GMT
Powered by
2

Displayed Message Possible Cause What to Do
Add Coffee, Coffee MAX. 1 Measure
A long coffee with pre-
ground coffee has
been
requested.
Place pre-ground coffee in the funnel and press
to continue and complete delivery.
Fill Beans Container
The coffee
beans have run out. Fill the beans container.
The grinding is too fine
and the coffee is
delivered too slowly
or not at all.
Repeat coffee delivery and turn the grinding
adjustment dial one click clockwise towards ‘7’
while the coffee mill is in operation. If after
making at least two coffees, delivery is still
too slow, repeat the correction
procedure, turning the grinding adjustment
dial another click until delivery is correct (see
section ‘Adjusting the coffee mill’). If the
problem persists, make sure the water tank is
fully inserted.
If you’re using a water
softener filter, an air
bubble may have
been released inside
the circuit, obstructing
Deliver some water through the hot water spout
until the flow becomes regular.
https://producthelp.fisherpaykel.com/nz/Cook/Companion_Products/Built-in_Coffee_Maker/EB60DSXBB1/Troubleshooting_a…
Updated: Wed, 12 Apr 2023 11:53:47 GMT
Powered by
3

Displayed Message Possible Cause What to Do
Ground too fine. Adjust Mill 1 click
while in Operation delivery.
Select a Milder Taste or Reduce Pre-
Ground Coffee Quantity
Too much coffee has
been used.
Select a milder strength by pressing
STRENGTH
or reduce the quantity of pre-ground
coffee (maximum 1 measure).
Insert Water Spout
The hot water spout is
not inserted or is not
inserted correctly.
Insert the water spout as far as it will go.
The milk container is
not inserted correctly. Insert the milk container as far as it will go.
https://producthelp.fisherpaykel.com/nz/Cook/Companion_Products/Built-in_Coffee_Maker/EB60DSXBB1/Troubleshooting_a…
Updated: Wed, 12 Apr 2023 11:53:47 GMT
Powered by
4

Displayed Message Possible Cause What to Do
Insert Milk Container
Insert Infuser Assembly
The infuser has
not been replaced
after cleaning.
Insert the infuser as described in section
‘Cleaning the infuser’.
Water Circuit Empty Press OK to Start
Filling Process
The water circuit is
empty.
Press
to deliver water from the spout until it flows out
normally. Delivery stops automatically. If the
problem persists, make sure the water tank is
fully inserted.
Press Ok to Start Cleaning Process or
The milk container has
been inserted with the
froth adjustment dial
in the CLEAN position.
To proceed with the CLEAN function, press
or turn the froth adjustment dial to one of the
milk positions.
https://producthelp.fisherpaykel.com/nz/Cook/Companion_Products/Built-in_Coffee_Maker/EB60DSXBB1/Troubleshooting_a…
Updated: Wed, 12 Apr 2023 11:53:47 GMT
Powered by
5

Displayed Message Possible Cause What to Do
Turn Milk Froth Adjustment Dial
Turn Dial to <Clean> Position to Start
Cleaning
Milk has
been delivered
recently and the tubes
inside the
milk container must be
cleaned.
Turn the froth adjustment dial to CLEAN.
Turn the Milk Froth Adjustment Dial to
Milk Position
The milk container has
been inserted with the
froth adjustment dial
in the CLEAN position.
Turn the dial to the required froth position.
Descaling Needed Press OK to Start
(~45 min)
The machine must be
descaled.
Press
to start descaling or BACK to descale later. The
descaling procedure described in
section ‘Descale’ needs to be performed.
https://producthelp.fisherpaykel.com/nz/Cook/Companion_Products/Built-in_Coffee_Maker/EB60DSXBB1/Troubleshooting_a…
Updated: Wed, 12 Apr 2023 11:53:47 GMT
Powered by
6

Displayed Message Possible Cause What to Do
Replace Water Filter Press OK to Start
The water
softener filter is
exhausted.
Press
to replace or remove the filter, or BACK to carry
out the procedure later. Follow the
instructions in section ‘Water softener filter’.
General Alarm: Refer to 'Cleaning' in the
User Guide
The inside of
the appliance is
very dirty.
Clean the inside of the appliance thoroughly,
as described in section ‘Cleaning’. If the
message is still displayed after cleaning,
contact Customer Care.
The appliance needs
descaling and/or the
filter
must be replaced.
The descaling procedure described in the
‘Descale’ section, needs to be performed and/or
the filter needs
replacing or removing as described in section
‘Water softener filter’.
The tubes inside the
milk container must be
cleaned.
Turn the froth adjustment dial to CLEAN.
The filter must be
replaced.
Replace the filter or remove it as described in
section ‘Water softener filter’.
https://producthelp.fisherpaykel.com/nz/Cook/Companion_Products/Built-in_Coffee_Maker/EB60DSXBB1/Troubleshooting_a…
Updated: Wed, 12 Apr 2023 11:53:47 GMT
Powered by
7

Displayed Message Possible Cause What to Do
The machine must be
descaled.
The descaling procedure described in section
‘Descale’ needs to be performed.
AUTO START
The auto-start function
is enabled.
To disable the function, proceed as described in
sectioN ‘Auto start’.
ENERGY SAVING
Energy saving
is enabled.
To disable energy saving, proceed as described
in section ‘Energy saving’.
Indicates that the filter
has been enabled
To remove the filter, proceed as described in
section ‘Water softener filter’.
CLEANING UNDERWAY PLEASE WAIT
The appliance
has detected
impurities in its
internal circuits.
Wait for the appliance to be ready for use again
and reselect the required beverage. Contact
Customer Care if the problem persists.
APPLIANCE TOO HOT
Using the
appliance continuously
for long periods
may cause the
appliance to overheat.
Wait for the appliance to cool down.
https://producthelp.fisherpaykel.com/nz/Cook/Companion_Products/Built-in_Coffee_Maker/EB60DSXBB1/Troubleshooting_a…
Updated: Wed, 12 Apr 2023 11:53:47 GMT
Powered by
8

Still Need Help?
You may need assistance from one of our qualified service technicians.
Click on the button below to schedule a visit.
BOOK A SERVICE
or Contact Us
https://producthelp.fisherpaykel.com/nz/Cook/Companion_Products/Built-in_Coffee_Maker/EB60DSXBB1/Troubleshooting_a…
Updated: Wed, 12 Apr 2023 11:53:47 GMT
Powered by
9