Fisher & Paykel CI905DTTB1 User manual

INSTALLATION GUIDE
NZ AU
MODULAR COOKTOP
MULTIPLE PRODUCT WITH DOWNDRAFT VENTILATION
CI905DTTB1, CI764DTTB1, CI604DTTB1, CI92DTTB1, CI92DB1,
CI02DB1, CI905DTTG1, CI764DTTG1, CI604DTTG1, CI92DTTG1,
CI92DG1, CI02DG1 CIT92DX1, CIT02DX1, CD1DB1 and
CD1DG1 models

2
!WARNING!
Electric Shock Hazard
Failure to follow this advice may result in
electric shock or death.
• Disconnect the appliance from the mains
electricity supply before carrying out any work
or maintenance.
• Connection to a good earth wiring system is
essential and mandatory.
• Alterations to the domestic wiring system must
only be made by a qualified electrician.
! WARNING!
Cut Hazard
Failure to use caution could result in injury.
• Take care: some edges are sharp.
SAFETY AND WARNINGS

3
READ AND SAVE THIS GUIDE
General Use
z Read these instructions carefully before installing this product.
z Save these instructions for the local electrical inspector’s use.
z Installation must comply with your local building and local electricity regulations.
z This appliance is to be installed and serviced only by Fisher & Paykel trained and
supported service technician or qualified person.
z The manufacturer accepts no responsibility for the incorrect installation of appliances.
Incorrect installation may result in personal injury, damage to property and may
invalidate any warranty or liability claims.
z Do not modify this appliance.
z Do not use or store flammable materials on or near this appliance.
z Packing elements (eg plastic bags, polystyrene foam, staples, packing straps etc) and
tools should not be left around during and after installation, especially if they are within
easy reach of children, as these may cause serious injuries.
z Make sure you recycle the packaging material.
z Before disposing of any appliance, make sure that it can no longer be used and that all
hazardous parts are removed or made harmless, so that children playing with the old
appliance cannot harm themselves.
z Only genuine replacement parts may be used for servicing the appliance. These are
available from your nearest Fisher & Paykel Service Center.
z This cooktop must be connected to the mains power supply only by a suitably
qualified person.
z DO NOT use adapters, reducers, or branching devices when connecting the cooktop to
the mains power supply to prevent overheating and fire.
z The power supply cable must not touch any hot parts and must be positioned so that
its temperature will not exceed 75°C at any point.
z This cooktop requires adequate supply of cool air to fully function. The base of the
cooktop must have direct unrestricted ventilation to the room where the cooktop is
installed. There must be a 4mm air gap at the front of the cooktop.
SAFETY AND WARNINGS

4
COMPONENTS REQUIRED
F Silicone gun
F Phillips screwdriver
F Level
F Box cutter
F Router
F Hex key
F Spanner
F Masking tape
F Duct tape
F Black installations:
Black, matte finish silicone rated
to 100°C or above*
F Grey installations:
Grey, matte finish silicone rated
to 100°C or above**
Not supplied
*Recommendation: Maxisil N30 Matte Black | **Recommendation: Maxisil A13 Anthracite

5
ACCESSING YOUR PRODUCT SPECIFICATIONS
For full product, cabinetry and service specifications, refer
to the Planning Guide. To access the Planning Guide, scan
the QR code or visit fisherpaykel.com/specify. Search by
appliance type, product name or model code.

6
PRIOR TO INSTALLATION
2. Create a 615x390mm cutout
in the base of the cavity for the
external blower.
Ensure cutout is oriented
correctly for selected ducting
option.
1. Ensure cabinetry and
servicing specifications have
been met and clearances have
been considered.
Refer to the Planning Guide for
details.
fisherpaykel.com/specify
615mm
390mm

7
1. Ensure all products and
accessories are present.
UNPACK ALL PRODUCTS
2. Carefully remove products
from cartons. Set aside on a
protected surface.
Dispose of packaging
responsibly.
3. Test electrical connections of
all products before proceeding
with installation.

8
PREPARE PRODUCTS
1. Remove foam tape backing
before attaching the downdraft
outlet and backing plate using
the supplied nuts and washers.
Ensure ducting orientation has
been considered.
2. If required, lift the inner box
out of the chassis. Remove
both downdraft alignment
guides and refit on the
opposite side.
Ensure the grease filter faces
the outlet.

9
INSTALL IN CUTOUT
1. Gently lower the first product
into the cutout.
2. Align the rear of the joining
bracket to the back edge of the
cutout and slot into place..
3. Fit cover onto joining bracket
before sliding it under the
adjacent product.

10
4. Gently lower additional
products and joining strips into
cutout as required.
INSTALL IN CUTOUT

11
1. Slot the T spacers between
the products. Adjust
positioning to ensure even
spacing between products is
achieved.
2. Flush installations:
Place the shims around the
outer edges of the cutout.
Adjust positioning to ensure
even spacing around the
product set is achieved.
3. Place the shims on top of
the product to gauge what
thickness is required to create a
level installation.
Slot the shims under the
products to raise as needed.
ALIGN PRODUCTS

12
SECURE TO CUTOUT
1. Fit the securing brackets to
the base of each cooktop. A
minimum of two brackets per
cooktop is recommended.
2. Tighten all clamp screws
to secure the cooktops to the
cutout and joiner strips.
3. Tighten the front and rear
clamping bracket screws to
secure the downdraft to the
cutout.

13
CONNECT POWER
Before connecting to the mains power supply check that:
zThe domestic wiring system is suitable for the power drawn by the cooktop.
zThe voltage corresponds to the value given on the rating plate.
zThe power supply cable sections can withstand the load specified on the rating plate.
CI604 AND CI764 MODELS
CI302, CI392, CIT302 AND CIT392 MODELS
CI905 MODELS
Single-phase connection
220–240V~
PE
1
2
3
4
5
N
L
1 L 3 L 2
PE
1
2
3
4
5
N
L
PE
1
2
3
4
5
N
L
PE
1
2
3
4
5
N
L
1 L 2
PE
1
2
3
4
5
N
L
1 L 2
PE
1
2
3
4
5
N
L
1 L 3 L 2
*
Single-phase connection
220–240V~
PE
1
2
3
4
5
N
L
1 L 3 L 2
PE
1
2
3
4
5
N
L
PE
1
2
3
4
5
N
L
PE
1
2
3
4
5
N
L
1 L 2
PE
1
2
3
4
5
N
L
1 L 2
PE
1
2
3
4
5
N
L
1 L 3 L 2
*
Three-phase connection
380–415V 3N~
PE
1
2
3
4
5
N
L
1 L 3 L 2
PE
1
2
3
4
5
N
L
PE
1
2
3
4
5
N
L
PE
1
2
3
4
5
N
L
1 L 2
PE
1
2
3
4
5
N
L
1 L 2
PE
1
2
3
4
5
N
L 1 L 3 L 2
*
Two-phase connection
380–415V 2N~
PE
1
2
3
4
5
N
L
1 L 3 L 2
PE
1
2
3
4
5
N
L
PE
1
2
3
4
5
N
L
PE
1
2
3
4
5
N
L 1 L 2
PE
1
2
3
4
5
N
L
1 L 2
PE
1
2
3
4
5
N
L
1 L 3 L 2
*
Refer to the Planning Guide for
full service information.
Single-phase connection
220–240V~
The models are supplied with a cable. This must be wired into a suitably rate plug,
permanent connection outlet or power isolator.
fisherpaykel.com/specify

14
1. Place the external blower into
the cutout and connect power
cord.
2. Cut ducting to required
lengths and slot together.
Secure and seal using duct
tape.
INSTALL DUCTING

15
LINK PRODUCTS
1. Link each product to the
adjacent product using the
supplied communication cables.
Ensure 8-pin plugs are only
connected to 8-pin sockets and
6-pin plugs connected to 6-pin
sockets.
2. Connect the downdraft unit
to the external blower via the
central communication cable.
3. Ensure all cables click into
place and are routed away from
cooktop exhausts.
Secure to cabinetry using the
supplied harness retainers.

16
SEAL PRODUCTS INTO CAVITY (FLUSH INSTALLATIONS)
1. Mask the area to be siliconed
ensuring all products and the
countertop are protected.
2. Carefully apply silicone in the
gaps between the countertop
and products.
Wipe away any excess silicone
and remove mask once silicone
has dried.

17
INSTALLER CHECKLIST
TO BE COMPLETED BY THE INSTALLER
GENERAL
Specified clearances have been maintained.
Products are level – front to back and side to side.
All packaging materials have been removed.
There is constant flow of cool air from the cabinetry to the base of the products.
Products have all been securely clamped.
Communication cables are routed away from cooktop exhuasts, secured to cabinetry
and are unobstructed by drawers or other objects.
Module layout configuration has been checked and confirmed.
Touch controls and displays are functioning.
Ducting has been secured and taped into place
ELECTRICAL
Receptacle with correctly rated over-current protection is provided for service
cord connection.
Adequate ground connection established.
Power supply cable is accessible and is not touching the products.

4102A 08.2
FISHERPAYKEL.COM
© Fisher & Paykel Appliances 2023. All rights reserved.
The models shown in this guide may not be available in all markets
and are subject to change at any time.
The product specifications in this guide apply to the specific products and
models described at the date of issue. Under our policy of continuous product
improvement, these specifications may change at any time.
For current details about model and specification availability in your country,
please go to our website or contact your local Fisher&Paykel dealer.