Fisher & Paykel OB60SC Series User manual

OB60NC, OB60SC & OB60SD
models
BUILT-IN OVEN
INSTALLATION GUIDE
NZ AU GB IE
590777E 0.19

1
IMPORTANT!
SAVE THESE INSTRUCTIONS
The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our
website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.
IMPORTANT SAFETY INSTRUCTIONS
 To avoid hazard, follow these instructions carefully
before installing or using this appliance.
 Please make this information available to the person
installing the appliance - doing so could reduce your
installation costs.
 This appliance must be installed and connected to
the mains power supply only by a suitably qualified
person according to these installation instructions and
in compliance with any applicable local building and
electricity regulations. Failure to install the appliance
correctly could invalidate any warranty or liability
claims.
 If the power supply cable is damaged, it must be
replaced by the manufacturer, its service agent or
similarly qualified person in order to avoid a hazard.
 Isolating switch: make sure this oven is connected
to a circuit which incorporates an isolating switch
providing full disconnection from the power supply in
accordance with the wiring rules.
 The oven must be earthed.
 Do not use adaptors, reducers or branching devices
to connect the oven to the mains electricity supply, as
they can cause overheating and burning.
 The appliance must not be installed behind a
decorative door in order to avoid overheating.
1SAFETY AND WARNINGS
WARNING!
Electrical shock hazard
Before carrying out any work on the
electrical section of the appliance, it must be
disconnected from the mains electricity supply.
Connection to a good earth wiring system is
absolutely essential and
mandatory.
Alterations to the domestic wiring system must
only be made by a qualified electrician.
Failure to follow this advice may result in
electrical shock or death.
WARNING!
Hot Surface Hazard
Take care - panel edges are sharp.
Failure to use caution could result in injury or
cuts.
WARNING!
Fire hazard
Do not use adapters, reducers, or branching
devices to connect this appliance to the mains
power supply.
Failure to follow this advice may result in
overheating, burning, or fire.
!
!
!

2
2PARTS SUPPLIED
3PRIOR TO INSTALLATION
4AFTER INSTALLATION
Screws (2) Metal side shelves
fixing nut (2)
 the benchtop and oven cavity are square and level, and are the required dimensions.
 the installation will comply with all clearance requirements and applicable standards and regulations.
 a suitable isolating switch providing full disconnection from the mains power supply is incorporated in the permanent wiring, mounted and positioned to comply with the local wiring rules and
regulations. The isolating switch must be of an approved type and provide a 3 mm air gap contact separation in all poles (or in all active [phase] conductors if the local wiring rules allow for this
variation of the requirements).
 the isolating switch will be easily accessible to the customer with the oven installed.
 there is at least 1.5 m (and not more than 2 m) free length of power supply cable within the cavity for ease of installation and servicing.
 the oven connection socket (if fitted) is outside the cavity if the oven is flush to the rear wall.
 the oven will rest on a surface that can support its weight.
 the height from the floor suits the customer.
 you consult local building authorities and by-laws if in doubt regarding installation.
Lower trim kit (for compact models only)
 compact models can be installed with a lower trim kit accessory to align the oven with companion products and cabinetry. If installing the lower trim kit accessory, ensure that this is installed
before the appliance.
IMPORTANT!
Some environmental factors and cooking habits can cause condensation in and around the oven during use. To protect surrounding cabinetry from possible damage caused by frequent or
excessive condensation, we recommend moisture-proofing the oven cavity.
IMPORTANT!
Please take extra care not to damage the lower trim of the oven during installation. The trim is important for correct air circulation and allows the door to open and close without
obstruction. The manufacturer does not accept any responsibility for damage resulting from incorrect installation.
 the oven door can open fully without obstruction.
 the power supply cable does not touch any hot metal parts.
 the isolating switch is easily accessible to the customer with the oven installed.
 you complete the ‘Final checklist’ at the end of the installation.
 If, after following the instructions given, correct performance cannot be achieved, please contact your nearest Fisher & Paykel Authorised Service Centre, Customer Care, or contact us through
our local website listed at the end of this document.

3
5PRODUCT DIMENSIONS
FRONT
TOP
SIDE
PRODUCT DIMENSIONS
OB60NC MODELS OB60SC MODELS OB60SD MODELS
MM MM MM
AOverall height of product 458
(with lower trim kit fitted) 479
598 598
BOverall width of product 597 597 596
COverall depth of product (excluding handle and dials) 565 565 565
DHeight of chassis 435 575 575
EWidth of chassis 552 552 556
FDepth of chassis 545 545 545
GDepth of oven frame and control panel
(=distance between front of chassis and front of oven door, excl. knobs)
20 20 20
HDepth of oven door when fully open
(measured from front of control panel)
340 450 460
A
C F
B
E
G
H
I
J
K
D
L
M
16-20 mm
2 mm
16-20 mm
Electrical supply
FLUSH INSTALL
PROUD INSTALL
Optional Lower trim kit shown (for compact models only)
(optional accessory. Purchased separately: Part no. 85083)
If using the lower trim kit accessory, you will need to install
this BEFORE installing the appliance. Refer to the
instructions packed with the lower trim kit.

4
TOP
SIDE
CABINETRY DIMENSIONS
OB60NC MODELS OB60SC MODELS OB60SD MODELS
MM MM MM
IMinimum inside width of cavity 560 560 560
JOverall width of cabinetry 600 600 600
KMinimum inside height of cavity 440
(with lower trim kit fitted) 461
580 580
LOverall height of cabinetry 460
(with lower trim kit fitted) 481
600 600
MMinimum inside depth of cavity 550 550 550
Note: If installing a cooktop above the oven, ensure adequate clearance is provided for the cooktop as per the cooktop manufacturer’s instructions.
5CABINETRY DIMENSIONS
A
C F
B
E
G
H
I
J
K
D
L
M
16-20 mm
2 mm
16-20 mm
Electrical supply
FLUSH INSTALL
PROUD INSTALL

5
6DISCARD PACKAGING RESPONSIBLY
Oven may vary
Recycle
responsibly
Remove the accessories box
from the top of the oven and set
aside.

6
7CONNECT THE OVEN TO THE MAINS SUPPLY
8SECURE THE OVEN TO THE CABINETRY
Oven may vary
Unclip
and lift up
L1N(L2)E
Brown
(Live)
Ensure cable
clamp is tightened
with screw
(you may have
to remove the
screw rst
before tting
the clamp)
L
N
Green
& Yellow
(Earth)
Blue
(Neutral)
IMPORTANT!
 This oven must be connected to the mains power supply only by a suitably
qualified person.
 This oven must be earthed.
MODEL CODE MAX POWER (W) HZ VOLTAGE (V) AMPS (A)
OB60NC*
OB60SD*
OB60SC*P*
OB60SC9D*
2800 - 3300 50 Hz 220 - 240 V~ 12.8 - 13.8
OB60SC*L*
OB60SCVM*
OB60SC*CEX
OB60SC*CEW
2700 - 3200 50 Hz 220 - 240 V~ 12.3 - 13.3
Before connecting the oven to the mains power supply, check that:
 the domestic wiring system is suitable for the power drawn by the oven
(as specified on the rating plate)
 the voltage corresponds to the value given on the rating plate.
1Position the oven in the prepared cavity.
IMPORTANT!
Do not lift the oven by the door handle.
2Open the oven door fully.
3Mark and pre-drill the screw holes.
4Use the supplied screws to secure the oven to the cabinetry.
IMPORTANT!
 Do not over-tighten the screws.
 Do not seal the oven into the cabinetry with silicone or glue. This makes
future servicing difficult. Fisher & Paykel will not cover the costs of
removing the oven, or of damage caused by this removal.

7
9FINAL CHECKLIST
TO BE COMPLETED BY THE INSTALLER
Make sure the oven is level and securely fitted to the cabinetry.
Check the lower trim is undamaged.
Open the oven door slowly until it is fully open and check there is adequate clearance between the bottom of the door and the lower trim.
This is to ensure correct air circulation. Should the lower trim become damaged, straighten the trim and ensure the oven door opens fully without obstruction.
Make sure you remove all internal packaging (including the circular yellow packing retainers holding the accessory box in place).
Make sure all oven vents and openings are clear and free of any obstruction or damage.
IMPORTANT!
Failure to make sure all oven vents are clear may result in poor product performance.
Make sure the isolating switch is accessible by the customer.
TEST OPERATION:
Turn the power to the oven on. For all models, except OB60SC5LCX, the display should light up and show 0:00.
Set the clock following the instructions in the ‘Quickstart Guide’ or ‘User guide’.
Turn the oven function to ‘Bake’. Inside the oven cavity, the oven light should come on. Air should blow out of the vent at the top of the oven.
Have you demonstrated the basic operation to the customer?
Turn the temperature to 50oC. The temperature indicator should come on. After five minutes, open the oven door: the air inside should feel warm.
Turn the oven function dial back to OFF.
Complete and keep for safe reference:
Model
Serial No.
Purchase Date
Purchaser
Dealer Address
Installer’s Name
Installer’s Signature
Installation Company
Installation Date

8

9