Fisher & Paykel OD301MV1-87818 Service manual

PAGE1OF8
P/N 545855E
DATEOFISSUE
11 /2003
INSTALLATION INFORMATION
AEROTECH BUILT- IN OVENS
0S301 / 0D301 SERIES
IMPORTANT- SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE

BEFORE YOU START PAGE 2 OF 8
Correct installation is the responsibility of the customer.
Ensure that the installer is properly qualified to install this oven.
= Make surethat theoven is locatedaway from anystrong and/or hot drafts of air,
• Thecabinet openingdimensionsspecifiedare the absoluteminimum. Thesedimensionsallow a clearance
of upto 1/4"(6mm).
° Theproductmust beelectrically grounded.See"ElectricalConnection"for details,
* We recommendthat the electricalsupplyjunction boxis locatedeither3" belowthe mainsupportsurfaceof
the productonthe right handsideor flush mountedinthe rear wall behindthe productor mountedin the
adjacentright-handsidecabinet. A 1" diameterholeshouldbe drilledin the right rearcornerof the oven
cabinetor inthe rearofthe right-handsidewall asrequiredto enablethe electricalsupply cordto be passed
throughthe cabinetto the junction box, Detailsofthese requirementsare shownin the diagramto the right.
* Theoven supportsurface shouldbeflat, leveland beableto supporta weight of at least 420 pounds(190 Kg)
for a doubleovenand 238 pounds(108 Kg)for singleovenmodels,
• Youwill needa No,2 Phillipsscrewdriverto completethe installationof the ovenintothe cabinet.
Thereshouldbe4 suitablewood screwswith this installationkit (Partnumber556075)and4 spacers
(Partnumber545455),
* A Fisher8 PaykelCE901cooktopcan be installedabovean 0S301singlewall ovenif a 3/8" (10mm)gap is
providedbetweenthe top of theovenandthe bottomof thecooktop.
It is thecustomersresponsibility:
•It isthe customersresponsibilityto ensurethat the product iselectricallyconnectedbya qualified
electricalinstallerin conformancewith the NationalElectricalcode,ANSI/NFPA70 (latest edition)and
all localcodes andordinances,
Junction Box
location for
undercounter
--installation
Junction Box
-- location for wall
installation
Copiesof the standardslisted may beobtainedfrom
* NationalFireProtectionAssociation
BatterymarchPark,Quincy,Massachusetts02269

PRODUCT DIMENSIONS
28 1/4" (718mm)
,\
51
29 3/4" (757mm)
......
E
O
LO
v
0S301
o
28 1/4" (718mm)
.\
_U --_ US
29 3/4" (757mm)
AE
E
O
LO
v
%
Z-
0D301
PAGE 3 OF 8
EA
E
p,..
F,
.C..
%
-.T.
p..

PROUD DiMENSiONS RECESSED DiMENSiONS
TOP VIEW
Minimum Distance
Under Benchtop
for Single
2 3/4" (70ram}
etN/idt h
=o
__
-4r_
Minimum Distance
Under Benchtop
for Single ovens
2 314"{70ram)
._
, _etWidth
PAGE 4 OF 8
TOP VIEW

PREPARING THE OVEN ELECTRICAL REQUIREMENTS
Unpacking the oven
Donot usedoorhandlesor any part of the controlpanelfor liftingthe product.
Beforethe productislifted, theoven doorsandracksare to beremoved.
-] ARNING: Extremecare is to betaken when lifting the productas it
is veryheavy. Failureto do somay resultin injury.
1. Carefullylaythe product on its back. Removethe externalwrappingandthe
bottom polystyreneprotector andpallet. Standthe productup and removeall
other polystyrenepackaging.
2. Removethe oven doors.This is done by:
•Openthe ovendoorfully.
• Lift the catcheson bothofthe hingesovertowards youontothe hooks
of the hingearm (seepicture below).
• Raisethe doorslightly, holdingon eitherside nearthe handle,making
surethatthe clips stay onthe hooks.
WARNING: Do notlift the doorout bythe handleas this may cause
damageto the product.
•Liftthe doorout. Door Hinge
Door
--_ ARNING: Do notdisengagethe hingehookswhen thedoorhas
been removedas theyarediffercult to re-engage.
3. Removethe wire shelvesand oven trays by slidingthem out. Useboth hands
to removeeachitem. Removethe cardboardpackagingfrom the ovencavity.
PAGE 5 OF 8
Theelectricalvoltage andfrequencythat is correctfor this ovenis stated onthe
serialnumberplate locatedinsidethe top vent. It isthe customerresponsibilityto
ensurethat this oven is connectedto the correctelectricalsupply.
WARNING :The oven mustbeconnectedto a permanentand
groundedsupply.
Maximum currentdraw: Maximum Load:
Double: 3&2 amps 9.2 kW
Single: 21 amps 5.1 kW
CONNECTOVENWITH COPPERWIREONLY
• Theflexible armouredcableshould be connecteddirectly to the junction box.
• Donot cut the conduit,
• A U.L.listed conduit connectormust be providedat thejunction box.
• Do not groundto a gas pipe.
• Donot havea fusein the groundingor neutralcircuit.
•Fusebothsidesof the line.
• A time delayfuse or circuit breakeris recommended. If using a time delay
fuse,thenfuse both sides ofthe line.
•Flexiblearmouredcable from the applianceshouldbe connecteddirectly to
the junction box.
• Connectdirectlyto the fused disconnect(or circuit breakerbox)throughflexible,
armoredor non-metallicsheathed,coppercable(with groundingwire).
• If codespermit anda separategroundingwire is used,it is recommended
that a qualifiedelectriciandeterminethat the groundingpathandwire gauge
is in accordancewith localcodes.
• Do not use an extensioncord with this appliance.