Fisher & Paykel OB76SD User manual

Built-in Oven
OB76SD & OB76DD models
NZ AU
INSTALLATION INSTRUCTIONS
590586E 10.15
www.fisherpaykel.com

1
IMPORTANT!
SAVE THESE INSTRUCTIONS
The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our
website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.
1SAFETY AND WARNINGS
WARNING!
Electrical shock hazard
Before carrying out any work on the electrical section of the appliance, it
must be disconnected from the mains electricity supply.
Connection to a good earth wiring system is absolutely essential and
mandatory.
Alterations to the domestic wiring system must only be made by a
qualified electrician.
Failure to follow this advice may result in electrical shock or death.
WARNING!
Cut hazard
Take care - some panel edges are sharp.
Failure to use caution could result in injury or cuts.
IMPORTANT SAFETY INSTRUCTIONS!
 Save these instructions for the local inspectors use.
 To avoid hazard, follow these instructions carefully before installing or using this appliance.
 Please make this information available to the person installing the appliance - doing so could
reduce your installation costs.
 This appliance must be installed and connected to the mains power supply only by a suitably
qualified person according to these installation instructions and in compliance with any
applicable local building and electricity regulations. Failure to install the appliance correctly
could invalidate any warranty or liability claims.
 If the installation requires alterations to the domestic electrical system, call a qualified
electrician. The electrician should also check that the socket cable section is suitable for the
electricity drawn by the oven.
 The oven must be earthed.
 If the power supply cable is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified person in order to avoid a hazard.
 Isolating switch: make sure this oven is connected to a circuit which incorporates an isolating
switch providing full disconnection from the power supply in accordance with the wiring rules.
 Do not use adaptors, reducers or branching devices to connect the oven to the mains
electricity supply, as they can cause overheating and burning.
 Make sure the cavity is completely sealed with no gaps. This is to ensure the oven cooling
system functions correctly.
WARNING!
Fire hazard
Do not use adapters, reducers, or branching devices to connect this
appliance to the mains power supply.
Failure to follow this advice may result in overheating, burning, or fire.
409 lb
186 kg
242 lb
110 kg
409 lb
186 kg
242 lb
110 kg
WARNING!
Very Heavy
Do not attempt to lift this product unassisted.
Lifting unassisted may cause serious injury.
SINGLE
oven
models
DOUBLE
oven
models

2
2PARTS SUPPLIED
3PRIOR TO INSTALLATION
4AFTER INSTALLATION
Screws
(2) for Single oven models
(4) for Double oven models
Spacers
(2) for Single oven models
(4) for Double oven models
 The benchtop and oven cavity are square and level, and are the required dimensions.
 The installation will comply with all clearance requirements and applicable standards and regulations.
 A suitable isolating switch providing full disconnection from the mains power supply is incorporated in the permanent wiring, mounted and positioned to comply with the local wiring rules and
regulations. The isolating switch must be of an approved type and provide a 3 mm air gap contact separation in all poles (or in all active [phase] conductors if the local wiring rules allow for this
variation of the requirements).
 the isolating switch will be easily accessible to the customer with the oven installed.
 The electrician provides sufficient free length of power supply cable to reach from the bottom rear of the cavity to at least 1.5 metres in front of the bottom edge of the opening.
 The cable may enter the cavity from the side, top or bottom, but top entry must be at the rear of the cavity.
 The oven connection socket (if fitted) is outside the cavity if the oven is flush to the rear wall.
 The oven will rest on a surface that can support its weight.
 The height from the floor suits the customer.
 You consult local building authorities and by-laws if in doubt regarding installation.
IMPORTANT!
Some environmental factors and cooking habits can cause condensation in and around the oven during use. To protect surrounding cabinetry from possible damage caused by frequent or
excessive condensation, we recommend moisture-proofing the oven cavity.
IMPORTANT!
Please take extra care not to damage the lower trim of the oven during installation. The trim is important for correct air circulation and allows the door to open and close without obstruction.
The manufacturer does not accept any responsibility for damage resulting from incorrect installation.
 The oven door(s) can open fully without obstruction.
 Do not seal the oven into the cabinetry with silicone or glue. This makes future servicing difficult. Fisher & Paykel will not cover the costs of removing the oven, or of damage caused by this removal.
 The power supply cable does not touch any hot metal parts.
 The isolating switch is easily accessible to the customer with the oven installed.
 You complete the ‘Final checklist’ at the end of the installation.
 If, after following the instructions given, correct performance cannot be achieved, please contact your nearest Fisher & Paykel Authorized Service Center, Customer Care, or contact us through our
local website listed at the end of this document.
Long Trim (1)
(to be fitted in a flush installation)

3
I
J
Electrical supply
H
B
C
A
D
G
F
E
M
K L
16-20 mm
2 mm
min.
39 mm
16-20 mm
2 mm
min.
39 mm
5PRODUCT DIMENSIONS - SINGLE OVENS
PLAN
PROFILE
FRONT
PRODUCT DIMENSIONS
OB76SD
MM
AOverall height of product 689
BOverall width of product 760
COverall depth of product (excludes handle and dials) 608
DDepth of oven front and control panel (excludes handle and dials) 39
EDepth of chassis (does not include oven front) 569
FHeight of chassis 675
GDepth of door (open) (measured from front of door) 530
HOverall width of chassis 720

4
5CABINETRY DIMENSIONS - SINGLE OVENS
PRODUCT DIMENSIONS
OB76SD
MM
AOverall height of product 689
BOverall width of product 760
COverall depth of product (excludes handle and dials) 608
DDepth of oven front and control panel (excludes handle and dials) 39
EDepth of chassis (does not include oven front) 569
FHeight of chassis 675
GDepth of door (open) (measured from front of door) 530
HOverall width of chassis 720
I
J
Electrical supply
H
B
C
A
D
G
F
E
M
K L
16-20 mm
2 mm
min.
39 mm
16-20 mm
2 mm
min.
39 mm
PLAN
PROFILE
CABINETRY DIMENSIONS
OB76SD
MM
IMinimum inside width of cavity 724
JOverall width of cabinetry 764
KMinimum inside height of cavity 681
LOverall height of cabinetry 693
MMinimum inside depth of cavity
Proud install
Flush install
575
613
Note: If installing a cooktop above the oven, ensure adequate clearance is provided for the cooktop as
per the cooktop manufacturer’s instructions.
IMPORTANT!
FLUSH INSTALLATION
The depth of the control panel (D)
is larger than conventional ovens.
Ensure you have created a
39 mm recess in cabinetry.
If flush installing, you need to
replace the lower trim with the
supplied long trim at the base
of the oven. Refer to Step 11 for
instructions.
IMPORTANT!
Make sure the cavity is completely
sealed with no gaps.
This is to ensure the oven cooling
system functions correctly.
PROUD INSTALL
FLUSH INSTALL

5
5PRODUCT DIMENSIONS - DOUBLE OVENS
K L
H
B
A
C
D
E
F
G
M
I
J
Electrical supply
16-20 mm
2 mm
min.
39 mm
16-20 mm
2 mm
min.
39 mm
PRODUCT DIMENSIONS
OB76DD
MM
AOverall height of product 1232
BOverall width of product 760
COverall depth of product (excludes handle and dials) 608
DDepth of oven front and control panel (excludes handle and dials) 39
EDepth of chassis (does not include oven front) 569
FHeight of chassis 1218
GDepth of door (open) (measured from front of door) 530
HOverall width of chassis 720
FRONT
PROFILE
PLAN

6
5CABINETRY DIMENSIONS - DOUBLE OVENS
K L
H
B
A
C
D
E
F
G
M
I
J
Electrical supply
16-20 mm
2 mm
min.
39 mm
16-20 mm
2 mm
min.
39 mm
CABINETRY DIMENSIONS
OB76DD
MM
IMinimum inside width of cavity 724
JOverall width of cabinetry 764
KMinimum inside height of cavity 1224
LOverall height of cabinetry 1236
MMinimum inside depth of cavity
Proud install
Flush install
575
613
IMPORTANT!
FLUSH INSTALLATION
The depth of the control panel (D) is larger
than conventional ovens. Ensure you have
created a 39 mm recess in cabinetry.
If flush installing, you need to replace the
lower trim with the supplied long trim at
the base of the oven. Refer to Step 11 for
instructions.
IMPORTANT!
Make sure the cavity is completely
sealed with no gaps.
This is to ensure the oven cooling
system functions correctly.
PROFILE
PLAN
FLUSH INSTALL
PROUD INSTALL

7
6DISCARD PACKAGING RESPONSIBLY
7REMOVE THE DOOR(S)
Recycle responsibly
Oven may vary
Lower trim
IMPORTANT!
When you remove the oven from the carton be
careful not to damage the lower trim. The trim is
important for both ventilation and to ensure the
door opens fully without obstruction.
Make sure you remove the Long Trim from the
packaging.
1
2
Single model shown for
illustration purposes only
IMPORTANT!
Do not lift the oven by the door handle.
1Hook the door swivel retainers onto the metal bar above them.
2Lift the oven door slightly to disengage the hinge.
3Pull the door forward off the appliance and lie it on a flat
surface.
Double oven models only:
Remove both doors.
1
2

8
8ELECTRICAL CONNECTION TO JUNCTION BOX
9SECURE THE OVEN TO THE CABINETRY
1Position the oven in the prepared cavity.
IMPORTANT!
Do not lift the oven by the door handle.
2Use the supplied screws and spacers to secure the oven to the
cabinetry.
Double oven models only:
There are 4 screws and spacers provided (two per side).
IMPORTANT!
 Do not over-tighten the screws.
 Take care not to damage the lower trim of the oven.
 Do not seal the oven into the cabinetry with silicone or glue.
This makes future servicing difficult. Fisher & Paykel will not
cover the costs of removing the oven, or of damage caused by
this removal.
Ensure supplied
spacer is fitted
between oven and
cabinetry
IMPORTANT!
 This oven must be connected to the mains power supply only by a suitably
qualified person.
 This oven must be earthed.
MODEL
CODE MAX POWER (KW) HZ VOLTAGE (V)
OB76SD 4.25 50 Hz 220 - 240 V~
OB76DD 8.50 50 Hz 220 - 240 V~
We recommend that the power outlet is located in the right rear corner of the
cabinet cavity. This allows the power supply cable to sit inside the rear chamfered
corner of the oven and prevents it being jammed between the cabinet wall and rear
of the oven.
Before connecting the oven to the mains power supply, check that:
 the domestic wiring system is suitable for the power drawn by the oven
(as specified on the rating plate)
 the voltage corresponds to the value given on the rating plate.
Note: For connection to the terminal block the maximum conductor size is 6 mm2.
Nameplate

9
!0 REFIT THE DOOR(S)
2
1
IMPORTANT!
Do not lift the oven by the door handle.
1Refit the door following the sequence in Step 7 in reverse
order.
Double oven models only:
Refit both doors.
1
2
1
1
2
1
Unscrew and remove the
installed lower trim Replace with the
supplied long trim
!1 FLUSH INSTALLATION ONLY - REPLACE THE LOWER TRIM WITH THE SUPPLIED LONG TRIM