Fisher & Paykel OB76SD User manual

NZ AU
590586C 07.14
OB76SD & OB76DD models
INSTALLATION INSTRUCTIONS
Built-in Oven

2
SAFETY AND WARNINGS
1
WARNING!
Electrical shock hazard
Before carrying out any work on the electrical section of the appliance, it must
be disconnected from the mains electricity supply.
Connection to a good earth wiring system is absolutely essential and
mandatory.
Alterations to the domestic wiring system must only be made by a qualified
electrician.
Failure to follow this advice may result in electrical shock or death.
WARNING!
Cut hazard
Take care - some panel edges are sharp.
Failure to use caution could result in injury or cuts.
IMPORTANT SAFETY INSTRUCTIONS!
To avoid hazard, follow these instructions carefully before installing or using this appliance.
Please make this information available to the person installing the appliance - doing so could
reduce your installation costs.
This appliance must be installed and connected to the mains power supply only by a suitably
qualified person according to these installation instructions and in compliance with any applicable
local building and electricity regulations. Failure to install the appliance correctly could invalidate
any warranty or liability claims.
If the power supply cable is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified person in order to avoid a hazard.
Isolating switch: make sure this oven is connected to a circuit which incorporates an isolating switch
providing full disconnection from the power supply in accordance with the wiring rules.
The oven must be earthed.
Do not use adaptors, reducers or branching devices to connect the oven to the mains electricity
supply, as they can cause overheating and burning.
WARNING!
Fire hazard
Do not use adapters, reducers, or branching devices to connect this appliance to
the mains power supply.
Failure to follow this advice may result in overheating, burning, or fire.
409 lb
186 kg
242 lb
110 kg
WARNING!
Very Heavy
Do not attempt to lift this product unassisted.
Lifting unassisted may cause serious injury.
SINGLE
oven
models
DOUBLE
oven
models

3
PRIOR TO INSTALLATION
AFTER INSTALLATION
2
3
the benchtop and oven cavity are square and level, and are the required dimensions.
the installation will comply with all clearance requirements and applicable standards and regulations.
a suitable isolating switch providing full disconnection from the mains power supply is incorporated in the permanent wiring, mounted and positioned to comply with the local wiring rules and regulations. The
isolating switch must be of an approved type and provide a 3 mm air gap contact separation in all poles (or in all active [phase] conductors if the local wiring rules allow for this variation of the requirements).
the isolating switch will be easily accessible to the customer with the oven installed.
the electrician provides sufficient free length of power supply cable to reach from the bottom rear of the cavity to at least 1.5 metres in front of the bottom edge of the opening.
The cable may enter the cavity from the side, top or bottom, but top entry must be at the rear of the cavity.
the oven connection socket (if fitted) is outside the cavity if the oven is flush to the rear wall.
the oven will rest on a surface that can support its weight.
the height from the floor suits the customer.
you consult local building authorities and by-laws if in doubt regarding installation.
Important!
Some environmental factors and cooking habits can cause condensation in and around the oven during use. To protect surrounding cabinetry from possible damage caused by frequent or excessive condensation, we recommend
moisture-proofing the oven cavity.
Important!
Please take extra care not to damage the lower trim of the oven during installation. The trim is important for correct air circulation and allows the door to open and close without obstruction. The manufacturer does not accept any
responsibility for damage resulting from incorrect installation.
the oven door(s) can open fully without obstruction.
the power supply cable does not touch any hot metal parts.
the isolating switch is easily accessible to the customer with the oven installed.
you complete the ‘Final checklist’ at the end of the installation.
If, after following the instructions given, correct performance cannot be achieved, please contact your nearest Fisher & Paykel Authorised Service Centre, Customer Care, or contact us through our local website listed at
the end of this document.
PARTS SUPPLIED
4
Screws
(2) for OB76SD
(4) for OB76DD
Spacers
(2) for OB76SD
(4) for OB76DD

4
5PRODUCT DIMENSIONS - SINGLE OVENS
Product dimensions (mm)
OB676SD
Aoverall height of product 689
Boverall width of product 760
Coverall depth of product (excluding handle and dials) 608
Dheight of chassis 675
Ewidth of chassis 720
Fdepth of chassis 569
Gdepth of oven frame and control panel
(=distance between front of chassis and front of oven door, excl. knobs) 39
Hdepth of oven door when fully open
(measured from front of control panel) 530
A
CF
B
E
G
H
D
TOP
FRONT SIDE

5
5CABINETRY DIMENSIONS - SINGLE OVENS
Cabinetry dimensions (mm)
OB676SD
Iminimum inside width of cavity 724
Joverall width of cabinetry 764
Kminimum inside height of cavity 681
Loverall height of cabinetry 693
Mminimum inside depth of cavity 575
Note: If installing a cooktop above the oven, ensure adequate clearance is provided for the cooktop as per the cooktop
manufacturer’s instructions.
I
J
K
L
M
16-20 mm
Electrical supply
min. 2 mm
16-20 mm
39 mm
39 mm
min. 2 mm
TOP
PROUD INSTALL
FLUSH INSTALL
SIDE
Important!
FLUSH INSTALLATION
The depth of the control panel (G) is larger than
conventional ovens. Ensure you have created a
38 mm recess in cabinetry.
If flush installing, you need to replace the lower
trim with the supplied long trim at the base of the
oven. Refer to Step 11 for instructions.
Important!
Make sure the cavity is completely sealed
with no gaps.
This is to ensure the oven cooling system
functions correctly.

6
5PRODUCT DIMENSIONS - DOUBLE OVENS
A
CF
B
E
G
H
D
16-20 mm
TOP
FRONT SIDE
Product dimensions (mm)
OB676DD
Aoverall height of product 1232
Boverall width of product 760
Coverall depth of product (excluding handle and dials) 608
Dheight of chassis 1218
Ewidth of chassis 720
Fdepth of chassis 569
Gdepth of oven frame and control panel
(=distance between front of chassis and front of oven door, excl. knobs) 39
Hdepth of oven door when fully open
(measured from front of control panel) 530

7
5CABINETRY DIMENSIONS - DOUBLE OVENS
Cabinetry dimensions (mm)
OB676DD
Iminimum inside width of cavity 724
Joverall width of cabinetry 764
Kminimum inside height of cavity 1224
Loverall height of cabinetry 1236
Mminimum inside depth of cavity 575
TOP
SIDE
K
L
M
16-20 mm
min. 2 mm
16-20 mm
39 mm
39 mm
min. 2 mm
I
J
Electrical supply
Important!
FLUSH INSTALLATION
The depth of the control panel (G) is larger than
conventional ovens. Ensure you have created a
38 mm recess in cabinetry.
If flush installing, you need to replace the lower
trim with the supplied long trim at the base of the
oven. Refer to Step 11 for instructions.
FLUSH INSTALL
PROUD INSTALL
Important!
Make sure the cavity is completely sealed
with no gaps.
This is to ensure the oven cooling system
functions correctly.

8
6
7
DISCARD PACKAGING RESPONSIBLY
REMOVE THE DOOR(S)
Recycle responsibly
lower trim
Important!
When you remove the oven from the carton be
careful not to damage the lower trim. The trim is
important for both ventilation and to ensure the
door opens fully without obstruction.
Make sure you remove the Long Trim from the
packaging.
Single model shown for illustration purposes only
Important!
Do not lift the oven by the door handle.
1 Hook the door swivel retainers onto the metal bar above them.
2 Lift the oven door slightly to disengage the hinge.
3 Pull the door forward off the appliance and lie it on a flat surface.
Double oven models only:
Remove both doors.
1
2

9
9SECURE THE OVEN TO THE CABINETRY
1 Position the oven in the prepared cavity.
Important!
Do not lift the oven by the door handle.
2 Use the supplied screws and spacers to secure the oven to the cabinetry.
Double oven models only:
There are 4 screws and spacers provided (two per side).
Important!
Do not over-tighten the screws.
Take care not to damage the lower trim of the oven.
Do not seal the oven into the cabinetry with silicone or glue. This makes future
servicing difficult. Fisher & Paykel will not cover the costs of removing the oven,
or of damage caused by this removal.
8CONNECT THE OVEN TO THE MAINS SUPPLY
Important!
This oven must be connected to the mains power supply only by a suitably qualified person.
This oven must be earthed.
Model code Max Power
(kW)
Hz Voltage (V)
OB76SD 4.25 50 Hz 220 - 240 V~
OB76DD 8.50 50 Hz 220 - 240 V~
We recommend that the power outlet is located in the right rear corner of the cabinet
cavity. This allows the power supply cable to sit inside the rear chamfered corner of
the oven and prevents it being jammed between the cabinet wall and rear of the oven.
Before connecting the oven to the mains power supply, check that:
the domestic wiring system is suitable for the power drawn by the oven
(as specied on the rating plate)
the voltage corresponds to the value given on the rating plate.
Note: For connection to the terminal block the maximum conductor size is 6 mm
2
.
Nameplate
Ensure supplied
spacer is fitted
between oven
and cabinetry

10
10
11
REFIT THE DOOR(S)
FLUSH INSTALLATION ONLY - REPLACE THE LOWER TRIM WITH THE SUPPLIED LONG TRIM
2
1
Important!
Do not lift the oven by the door handle.
1 Refit the door following the sequence in Step 7 in reverse order.
Double oven models only:
Ret both doors.
1
1
2
Unscrew and remove the
installed lower trim Replace with the
supplied long trim
Ensure the clips
on the long trim
locate into the
channels

11

12 FINAL CHECKLIST
Important!
SAVE THESE INSTRUCTIONS
The models shown in this document may not be available in all markets and are subject to change
at any time. For current details about model and specification availability in your country, please
visit our website listed at the end of this document or contact your local Fisher & Paykel dealer.
www.sherpaykel.com
TO BE COMPLETED BY THE INSTALLER
Make sure the oven is level and securely fitted to the cabinetry.
Check the lower trim is undamaged.
Open the (lower) oven door slowly until it is fully open and check there is
adequate clearance between the bottom of the door and the lower trim.
This is to ensure correct air circulation. Should the lower trim become
damaged, straighten the trim and ensure the oven door opens fully without
obstruction.
Make sure any cable ties and internal packaging has been removed from the
oven cavity.
Make sure all oven vents and openings are clear and free of any
obstruction or damage.
Important!
Failure to make sure all oven vents are clear may result in poor product
performance.
Make sure the isolating switch is accessible by the customer.
TEST OPERATION:
Turn the power to the oven on. The display should light up and show
:. Set the clock following the instructions in the ‘Quickstart Guide’.
Turn the oven function to ‘Bake’. Inside the oven cavity, the oven light should
come on. Air should blow out of the vent at the top of the oven.
Have you demonstrated the basic operation to the customer?
Turn the temperature to 50
o
C. The temperature indicator should come on.
After five minutes, open the oven door: the air inside should feel warm.
Turn the oven function dial back to OFF.
Installer’s name:
Installer’s signature:
Installation company:
Date of installation:
LEAVE THESE INSTRUCTIONS WITH THE CUSTOMER