Fisher & Paykel EB60 User manual

COMPANION PRODUCTS
Coee Maker EB60
Steam Oven OS60
Microwave Oven OM60
models
INSTALLATION GUIDE
NZ AU GB IE

CONTENTS
IMPORTANT!
SAVE THESE INSTRUCTIONS
The models shown in this user guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country,
please go to our website fisherpaykel.com or contact your local Fisher & Paykel dealer.
Coffee maker 13
1 Safety and warnings 1
2 Parts supplied 2
3 Prior to installation 3
4 After installation 3
5 Product dimensions 4
6A Cabinetry dimensions
(460mm high cavity) 5
6B Cabinetry dimensions
(480mm cavity trim kit) 6
7 Installation instructions 7
8 Final checklist 8
Steam oven 9
1 Safety and warnings 10
2 Parts supplied 11
3 Prior to installation 11
4 After installation 12
5 Product dimensions 13
6A Cabinetry dimensions
(460mm high cavity) 14
6B Cabinetry dimensions
(480mm cavity trim kit) 15
7 Installation instructions 15
8 Final checklist 16
Microwave oven 17
1 Safety and warnings 18
2 Prior to installation 19
3 After installation 19
4 Product dimensions 20
5A Cabinetry dimensions
(460mm high cavity) 21
5B Cabinetry dimensions
(480mm cavity trim kit) 22
6 Electrical hook-up 23
7 Secure the oven to the cabinetry 23
8 Final checklist 24

COFFEE MAKER
EB60 models

2|COFFEE MAKER INSTALLATION GUIDE
IMPORTANT SAFETY INSTRUCTIONS!
Installation
Checking for transport damage
After removing the packaging, make sure the product is complete and undamaged and that all
accessories are present. Do not use the appliance if it is visibly damaged. Contact Customer Care.
IMPORTANT!
● Installation must be performed by a qualified professional in compliance with legislation in
force in the country of installation (see section “Built-in installation”).
● The packing elements (plastic bags, polystyrene foam, etc.) should be kept out of reach of
children.
● Never install the appliance in rooms where the temperature may drop to 0°C or lower.
● Customise the water hardness as soon as possible following the instructions in the “Water
hardness” section.
● This appliance can be installed over a built-in oven if the latter is fitted with a cooling fan at
the rear (maximum microwave power: 3 kW).
● Connecting the appliance
● Danger! Check that the mains power supply voltage corresponds to the value indicated on
the rating plate on the bottom of the appliance.
● Connect the appliance to an efficiently earthed and correctly installed socket with a
minimum current rating of 10A only.
● If the power socket does not match the plug on the appliance, have the socket replaced
with a suitable type by a qualified professional. To comply with safety directives, an
omnipolar switch with a minimum contact distance of 3 mm must be installed.
● Do not use multiple sockets or extensions.
● Safety cutout devices must be included in the mains power supply in compliance with the
installation regulations in the country concerned.
● This appliance conforms to EC Regulation 1935/2004 on materials and articles intended to
come into contact with food.
DISPOSAL
● The appliance must not be disposed of with household waste, but taken to an authorised
waste separation and recycling centre.
IMPORTANT!
SAVE THESE INSTRUCTIONS
The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country,
please go to our website fisherpaykel.com or contact your local Fisher & Paykel dealer.
1SAFETY AND WARNINGS
WARNING!
Cut Hazard
Take care – some edges are sharp.
Failure to use caution could result in injury or cuts.

COFFEE MAKER INSTALLATION GUIDE|3
2PARTS SUPPLIED
3PRIOR TO INSTALLATION
4AFTER INSTALLATION
Screws
(28)
Spacers
(4) for side
(4) for bottom
● The countertop and coffee maker cavity are square and level, and are the required dimensions.
● The installation will comply with all clearance requirements and applicable standards and regulations.
● The isolating switch will be easily accessible to the customer with the coffee maker installed.
● The electrician provides sufficient free length of power supply cable to reach from the bottom rear of the cavity
to at least 1.5m in front of the bottom edge of the opening.
● The cable may enter the cavity from the side, top or bottom, but top entry must be at the rear of the cavity.
● The coffee maker connection socket (if fitted) is outside the cavity if the oven is flush to the rear wall.
● The coffee maker will rest on a surface that can support its weight.
● The height from the floor suits the customer.
● You consult local building authorities and by-laws if in doubt regarding installation.
IMPORTANT!
Some environmental factors and cooking habits can cause condensation in and around the coffee maker during use.
To protect surrounding cabinetry from possible damage caused by frequent or excessive condensation, we recommend
moisture-proofing the cavity.
IMPORTANT!
Take extra care not to damage the lower trim of the coffee maker during installation. The trim is important for correct air circulation and allows the door to open and close without obstruction.
The manufacturer does not accept any responsibility for damage resulting from incorrect installation.
● The coffee maker can be used fully without obstruction.
● The power supply cable does not touch any hot metal parts.
● The isolating switch is easily accessible to the customer with the coffee maker installed.
● You complete the ‘Final checklist’ at the end of the installation.
● If, after following the instructions given, correct performance cannot be achieved, please contact your nearest Fisher & Paykel Authorised Service Center, Customer Care, or
contact us through our local website listed at the end of this document.
Rails (2)Lock Hook (1) Clip (1)
Optional Trim kit installation
If you are using a 762mm trim kit, refer
to the separate Trim Kit Installation Guide.

4|COFFEE MAKER INSTALLATION GUIDE
5PRODUCT DIMENSIONS
FRONT
TOP SIDE
PRODUCT DIMENSIONS
EB60 MODELS
mm
AOverall height of product 458
BOverall width of product 596
COverall depth of product 480
DHeight of chassis 445
EWidth of chassis 560
FDepth of chassis 460
GDepth of coffee maker frame and control panel 20
HStepdown control panel to chassis 13
IHeight of control panel 100
B
E
A
CF D
I
H

COFFEE MAKER INSTALLATION GUIDE|5
Verify the minimum measurements required for correct installation of the appliance. The coffee maker must be
installed in a column and the column must be firmly fixed to the wall with commercially available brackets.
IMPORTANT!
● All installation or maintenance operations must be performed with the appliance disconnected
from the mains electricity supply.
● Kitchen furniture in direct contact with the appliance must be heat resistant 65°C min.
● To guarantee correct ventilation, leave a gap at the bottom of the cabinet
(see measurements below).
6ACABINETRY DIMENSIONS (460mm HIGH CAVITY)
PROUD INSTALL
FLUSH INSTALL
16–20mm
2mm
16–20mm
Electrical supply
CABINETRY DIMENSIONS
EB60 MODELS
mm
IMinimum inside width of cavity 560
JOverall width of cabinetry 600
KMinimum inside height of cavity 450
LOverall height of cabinetry 460
MMinimum inside depth of cavity 545
nVentilation Air Gap 50
TOPSIDE
M
J
I
Lk
n
20mm
20mm

6|COFFEE MAKER INSTALLATION GUIDE
Verify the minimum measurements required for correct installation of the appliance. The coffee maker must be
installed in a column and the column must be firmly fixed to the wall with commercially available brackets.
IMPORTANT!
● All installation or maintenance operations must be performed with the appliance disconnected
from the mains electricity supply.
● Kitchen furniture in direct contact with the appliance must be heat resistant 65°C min.
● To guarantee correct ventilation, leave a gap at the bottom of the cabinet
(see measurements below).
6BCABINETRY DIMENSIONS (480mm CAVITY TRIM KIT)
TOPSIDE
Electrical supply
o
Lower
Trim kit
M
J
I
Lk
n
CABINETRY DIMENSIONS
EB60 MODELS
mm
IMinimum inside width of cavity 560
JOverall width of cabinetry 600
KMinimum inside height of cavity 470
LOverall height of cabinetry 480
MMinimum inside depth of cavity 545
nVentilation air vent 50
oHeight of trim kit 20
PROUD INSTALL
FLUSH INSTALL
16–20mm
2mm
16–20mm
20mm
20mm

COFFEE MAKER INSTALLATION GUIDE|7
2 mm
x 28 x 2 x 1
(=) (=)
1Position the rails on the sides of the
cabinet. Fix with the screws provided,
then extend the rails completely.
● Position and fix the lock hook with
the four screws provided, as shown.
● If the coffee maker is installed over a
warmer drawer, use the top surface
of this as a reference to position the
rails. In this case, there will be no
surface to rest the rails on. 2Fix the power cable with the clip. The power cable must be long enough to allow
the appliance to be pulled out from the cabinet to fill the coffee bean container.
● The appliance must be earthed in compliance with legislation.
● Electrical connections must be performed by a qualified electrician following
the instructions.
3Position the appliance on the rails, making sure the pins are correctly inserted
in the housings, then fix it with the screws supplied. If the height of the appliance
requires adjusting, use the spacer disks provided.
5
4If necessary, correct alignment of the appliance by positioning the spacers
supplied under or at the sides of the support.
5To lift the appliance in the front (max. 2mm) turn the latch as shown.
7INSTALLATION INSTRUCTIONS
approx. 350mm
560mm + 1mm
2mm

8|COFFEE MAKER INSTALLATION GUIDE
8CONNECT THE WARMING DRAWER TO THE MAINS SUPPLY
IMPORTANT!
● All electrical work may only be carried out by suitably qualified and competent persons in accordance with national and
local safety regulations.
● This warming drawer must be earthed.
Before placing the coffee maker into the cavity, route the power cord into the back of the cavity and plug it in to the switched
socket. The switched socket should be in an easily accessible area within 900mm of the centre rear of the product.
Power requirements
Model Code Power Voltage Wattage Hz
EB60 6.1 A 220-240 V 220-240 W 50-60 Hz