Fisher & Paykel OR24SDPWGX User manual

instructions d'installation
OR24SDPWGX model

WARNING
,, ALL RANGES CAN TiP
,, iNJURY TO PERSON COULD RESULT
,, iNSTALL ANTI=TIP DEVICE PACKED
WiTH RANGE
,, SEE iNSTALLATiON iNSTRUCTiONS
WARNING" IF THE INFORMATION IN THIS MANUAL IS NOT
FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT
CAUSING PROPERTY DAMAGE, PERSONAL INJURY, OR
J Do not store or use gasoline or other flammable vapors and liquids
in the vicinity of this or any other appliance.
JWHAT TO DO IF YOU SMELL GAS:
•Do not try to light any appliance.
•Do not touch any electrical switch; do not use any phone in your
building.
• Immediately call your gas supplier from a ne=ghbor's phone.
Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire department.
J Installation and service must be performed by a qualified installer,
serwce agency, or the gas supplier.
This appliance is designed and manufactured solely for the cooking of domestic (household)
food and in not suitable for any none domestic application and therefore should not be used
in a commercial environmement.
The appliance guarantee will be void if the appliance is used within a non domestic
environnement i.e. a semi commercial, commercial or communal environment.

DATA PLATE CONVERSION LABEL
IMPORTANT - PLEASE READ AND FOLLOW
¢" Before beginning, please read these instructions completely and
carefully.
¢" Do not remove permanently affixed labels, warnings, or plates
from the product. This may void the warranty.
¢" Please observe all local and national codes and ordinances.
¢" Please ensure that this product is properly grounded.
J The electrical plug should always be accessible.
J" The installer should leave these instructions with the consumer
who should retain for local inspector's use and for future reference.
®
Installation must conform with local codes or in the absence of codes, the National Fuel Gas Code ANSIZ223.1
- latest edition. Electrical installation must be in accordance with the National Electrical Code, ANSI/NFPA70
- latest edition and/or local codes. IN CANADA: Installation must be in accordance with the current CAN/
CGA-B149.1 National Gas Installation Code or CAN/CGA-B149.2, Propane Installation Code and/or local
codes. Electrical installation must be in accordance with the current CSA C22.1 Canadian Electrical Codes
Part 1 and/or local codes.
INSTALLATION IN MANUFACTURED (MOBILE) HOME: The installation must conform with the Manufactured
Home Construction and Safety Standard, Title 24 CFR, Part 3280 [formerly the Federal Standard for Mobile
Home Construction and Safety, Title 24, HUD (Part 280)] or, when such standard is not applicable, the
Standard for Manufactured Home Installations, ANSI/NCSBCS A225.1, or with local codes where appli-
cable.
INSTALLATION IN RECREATIONAL PARK TRAILERS: The installation must conform with state or other codes
or, in the absence of such codes, with the Standard for Recreational Park Trailers, ANSI A119.5.
Installation of any gas-fired equipment should be made by a licensed plumber. A manual gas shut-off valve
must be installed in the gas supply line ahead of the appliance in the gas stream for safety and ease of ser-
vice.
If an external electrical source is utilized, the appliance, when installed, must be electrically grounded in
accordance with local codes or, in the absence of local codes, with the national Electrical Code, ANSI/NFPA
70.
This range is supplied with a protective film on steel and aluminium parts:
This film must be removed before installing/using the appliance.
IFOR INSTALLER ONLY I
ITHIS RANGE IS FOR RESIDENTIAL USE ONLY I

WARNING!
THIS APPLIANCE HAS TO BE INSTALLED BY A QUALIFIED INSTALLER.
Improper installation, adjustment, alteration, services, or maintenance can cause injury or property damage. Consult a
qualified installer, service agent, or the gas supplier.
IMPORTANT: The use of suitable protective clothing/gloves is recommended when handling, installing of this appliance.
TOOLS NEEDED FOR INSTALLATION (NOT SUPPLIED WITH THE APPLIANCE)
Screwdriver 2 -Wrench
Hammer
T-handle
wrench
Adjustable
wrench
Pencil Tape measure
i_i!i!i_i!i_i_!!__i_i_i_i_w_i_,,,,,i_iii_iii _ _ii
Drill

GENERAL INFORMATION
1. Installation must conform with local codes or, in the absence
of local codes, with the National Fuel Gas Code, ANSI
Z223.1-Latest Edition, CAN/CGA-B149.1 or CAN/CGA-
B149.2.
2. Installation in manufactured (mobile) home: installation
must conform with the Manufactured Home Construction
and Safety Standard, Title 24 CFR, Part 3280 [formerly
the Federal Standard for Mobile Home Construction and
Safety, Title 24, HUD (Part 280)] or, when such standard
is not applicable, the Standard for Manufactured Home
Installations, ANSl/NCSBCS A225.1, or with local codes
where applicable.
3. Installation in Recreational Park Trailers: installation must
conform with state or other codes or, in the absence of
such codes, with the Standard for Recreational Park
Trailers, ANSI Al19.5.
WARNING!!
ELECTRICAL GROUNDING INSTRUCTIONS
The range must be electrically grounded in accordance
with local codes or, in the absence of local codes, with
the National Electrical Code, ANSl/NFPA No. 70-latest
edition, in Canada Canadian Electrical Code.
Installation should be made by a licensed electrician.
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED.
If an external electrical source is utilized, the installation must
be electrically grounded in accordance with local codes or, in
the absence of local codes, with the national Electrical Code,
ANSl/NFPA 70.
This appliance is equipped with a four-prong grounding plug
(NEMA 14-50P) for your protection against shock hazard and
should be plugged directly into a properly grounded socket.
4WARNING!!
This appliance shall not be used for space heating. This
information is based on safety considerations.
Do not under any circumstances cut or remove the fourth
(ground) prong from the power plug.
5. All openings in the wall behind the appliance and in the floor
under the appliance shall be sealed.
6. Keep appliance area clear and free from combustible
materials, gasoline, and other flammable vapors.
7. Do not obstruct the flow of combustion and ventilation air.
REPLACEMENT PARTS
Only authorized replacement parts may be used in performing
service on the range. Replacement parts are available from
factory authorized parts distributors. Contact the nearest parts
distributor in your area.
8. Disconnect the electrical supply to the appliance before
servicing.
9. When removing appliance for cleaning and/or service;
A. Shut off gas at main supply.
B. Disconnect AC power supply.
C. Disconnect gas line to the inlet pipe.
D. Carefully remove the range by pulling outward.
CAUTION: Range is heavy; use care in handling.
10. Electrical Requirement
Electrical installation should comply with national and local
codes.
11. Air Supply and Ventilation
The installer must refers to local/national codes.
12. Gas Manifold Pressure
Natural gas - 4.0" W.C.R
LP/Propane - 11.0" W.C.R
13. The misuse of oven door (e.g. stepping, sitting, or leaning
on them) can result in potential hazards and/or injuries.
14. When installing or removing the range for service, a rolling
lift jack should be used. Do not push against any of the
edges of the range in an attempt to slide it into or out of
the installation. Pushing or pulling a range (rather than using
a lift jack) also increases the possibility of bending the leg
spindles or the internal coupling connectors.

installation
%
¢o
Z
_.1.1
PROXIMITY TO SIDE CABINETS
• This range may be installed directly adjacent to existing 36" (914 mm) high base
cabinets•
2,
3.
Range dimensions:
•width: 23" 7/8 (606.5 mm)
• depth: 24" 11/64 (614.1 mm)
• height (without backguard): MIN 35" 17/32 (902.5 mm) - MAX 36" 7/32 (920 mm)
• backguard (height): 4" 7/16 (113 mm)
Gas line opening:
Wall - 7" 9/32 (185 mm) from the floor; 5" 57/64 (150 mm) from the rear right side
of the range.
The electric cord with 4-prong ground plug (NEMA 14-50P) has a length of 72"
+1 "1/2 (1830 mm +38 mm).
Grounded outlet should be located 7" 9/32 (185 mm) from the floor and 17" 31/32
(456.5 mm) from the rear left side of the range.
The range CANNOT be installed directly adjacent to sidewalls, tall cabinets, tall
appliances, or other side vertical surfaces above 36" (914 mm) high.
There must be a minimum of 3" (76 mm) side clearance from the range to such
combustible surfaces TO THE LEFT above the 36" (914 mm) high countertop; or
there must be a minimum of 11" 13/16 (300 mm) side clearance from the range to
such combustible surfaces TO THE RIGHT above the 36" (914 mm) high counter-
top.
IMPORTANT: One side (left or right) above the 36" (914 mm) high countertop
must always be kept clear.
The maximum upper cabinet depth recommended is 13" (330 mm). Wall cabinet
above the range must be a minimum of 30" (762 mm) above the countertop for a
width of minimum 24" (609.6 mm): it has to be centred with the range. Side wall cab-
inets above the range must be a minimum of 18" (457 mm) above the countertop.
Dotted line showing the position
of the range when installed
Area for ELECTRICAL
connection
GAS AND ELECTRIC CONNECTION
Area for GAS connection
\
\
Fig. 1.2
J
J

PROXIMITY TO SIDE CABINETS
Fig. 1.3
ram) 13"maX.(330ram)
ASSEMBLING THE BACKGUARD
It is mandatory to install the backguard
Assemble the backguard as shown in figure 1.5:
• Screw the 2 screws "A" interposing the spacers.
• Screw the central screw "B".
Fig. 1.5 7

LEVELLING THE RANGE
The range is equipped with 4 LEVELLING FEET (supplied in a separate kit) and may be
levelled by screwing or unscrewing the feet (fig. 1.8).
It is important to observe the directions of figures 1.6, 1.7a, 1.7b.
+
+8ram
I I#
°&
& & Fig. 1.6
Supplied with the range
in a separate kit
/...... \
+5/16"
Supplied with the range
in a separate kit
&
Fig. 1.7a +11/16" Fig. 1.7b
)_17.5mm J
YOU MUST USE STABILITY
ANTI TIP BRACKET TO
PREVENT UNIT FROM
TIPPING.
ANTI-TIP STABILITY DEVICE INSTALLATION INSTRUCTIONS
1. The anti-tip bracket has to be attached as shown on figure below (only rear left side),
it has to be fixed on the floor and on the rear wall by no. 4 (four) suitable screws (not
supplied).
2. After fixing the anti-tip bracket, slide range into place. Be sure the rear left foot slides
under the anti-tip bracket attached.
ANTI-TIP STABILITY
DEVICE FIXING
Anti-tip stability
device Rear left
feet of range
Dotted line showing the position
of the range when installed
/
Fig. 1.9
8

gas connection
All gas connections must be made according to national and local codes. This
gas supply (service) line must be the same size or greater than the inlet line of the
appliance. Sealant on all pipe joints must be resistant to the action of LP/Propane
gas.
The range is equipped for the use with NATURAL gas. It is design-certified by CSA
International for NATURAL and L.R gases with appropriate conversion.
The model/serial rating plate, located on the back of the appliance, has information
on the type of gas that can be used. If this information does not agree with the type
of gas available, check with the local gas supplier. See page from 13 to 15 for L.R
gas conversion instructions.
1. Manual Shut-off Valve (fig:2.1):
The supply line shall be equipped with an approved shutoff valve. This valve should
be located in the same room as the range and should be in a location that allows
ease of opening and closing (in a position where it can be reached quickly in the
event of an emergency).
Do not block access to the shutoff valve. The valve is for turning on or shutting off
gas to the appliance.
Shutoff valve
"open" position
To range \
_e
Fig. 2.1
WARNING
Explosion Hazard
Use a new CSA or UL approved
gas supply line.
Install a shut-off valve.
Securely tighten all gas connec-
tions.
If connected to LP, have a quali-
fied person make sure gas pres-
sure does not exceed 14" water
column.
Examples of aqualified person
include licensed heating per-
sonnel, authorized gas compa-
ny personnel, and authorized
service personnel.
Failure to do so can result in
death, explosion, or fire.
2. Pressure Regulator:
a) All heavy duty, commercial type cooking equipment must have a pressure regulator
on the incoming service line for safe and efficient operation, since service pressure
may fluctuate with local demand.
Before installing the regulator mount the 1/2" NPT (conical) male connector to the
regulator (see picture 2.2). Gasket supplied have to be placed between 1/2" NPT
(conical) connector/extension pipe male pipe fitting (see picture 2.3).
The regulator supplied with this range must be installed before any gas connections
are made.
Use supplied pressure regulator only.

PRESSURE REGULATOR INSTALLATION
STEP 1
Mount the 1/2" NPT (conical) male connector to the pressure
regulator and tighten by using a wrench.
Do not over tighten the connector.
Over tightening may crack regulator.
LOCK
Fig. 2.2
STEP 2
Assemble the 1/2" NPT connector + pressure regulator group to the extension pipe interposing the gasket supplied. The
regulator cover must be oriented toward the front side of the range.
IMPORTANT: use two spanners to tighten the connection.
Regulator cover Fig. 2.3
10

GAS CONNECTION SPECIFICATION
manifold
I/2" G cylindrical
(ISO 228-I) male
IManifold male pipe fitting /
J
J
J
J
J
J
EXtension
ipe femak
pipe fitting
Extension
pipe male
pipe fitting
I/2" NPT (conical)
male
1/2" G cylindrical
ISO 228-I) female
E×tensi
pipe
I/2" G cylindrical
(ISO 228-I) male
I/2" G cylindrical
(ISO 228-I) female
I'
Con"eCto,1
h1/2" NPT
:: female
,[!
To mares
connection
I egulato,/ essu'e
mr !
I/2" NPT
female
Arrow
\\\ J
WARNING: check the right positioning
of the gas regulator. The arrow on the
back of the gas regulator must be
oriented toward the connector. Fig. 2.4
11

TEST POINT ADAPTER
The Test Point adapter is available
from the After-Sales Service.
\
Fig. 2.5
b) Any conversion required must be performed by your dealer or a qualified licensed
plumber or gas service company. Please provide the service person with this
manual before work is started on the range. (Gas conversions are the responsibility
of the dealer or end user.)
c) This range can be used with NATURAL or LP/PROPANE gas. It is shipped from
the factory adjusted for use with NATURAL gas.
d) Manifold pressure should be checked with a manometer and by operating as
below detailed:
- Remove the injector from the front left burner and mount the proper test point
adapter which is available from the After-Sales Service (see side figure and the
"OPERATIONS TO BE PERFORMED WHEN SUBSTITUTING THE INJECTORS"
chapter).
- Turn the front left burner control knob to the maximum position HI.
- Press the knob and keeping it pressed check the manifold pressure with a
manometer; NATURAL gas requires 4.0" W.C.R and LP/PROPANE requires 11.0"
W.C.R
- Incoming line pressure upstream from the regulator must be 1" W.C.R higher
than the manifold pressure in order to check the regulator.
- The regulator used on this range can withstand a maximum input pressure of
1/2 PSI (14.0" W.C.P). If the line pressure is in excess of that amount, a step-
down regulator will be required.
e) The appliance, its individual shut-off valve, and pressure regulator must be
disconnected from the gas supply piping system during any pressure testing of
that system at pressures in excess of 1/2 PSI (3.5 kPa).
f) The appliance must be isolated from the gas supply piping system by closing its
individual manual shut-off valve during any pressure testing of the gas supply
piping system at test pressure equal to or less than 1/2 PSI (3.5 kPa).
3. Flexible Connections:
If local codes permit, CSA design-certified, flexible metal appliance connector is
recommended for connecting this range to the gas supply line. Do Not kink or damage
the flexible connector when moving the range. The pressure regulator has 1/2" NPT
female pipe threads.You will need to determine the fittings required, depending on
the size of your gas supply line, flexible metal connector and shutoff valve.
4. Rigid Pipe Connections:
If rigid pipe is used as a gas supply line, a combination of pipe fittings must be used
to obtain an in-line connection to the range. All strains must be removed from the
supply and fuel lines so range will be level and in line.
• Use joint compounds and gaskets that are resistant to action of natural or
propane gas on all male pipe threads.
• Do not over tighten gas fitting when attaching to pressure regulator. Over
tightening may crack regulator.
5. Leak Testing:
IMPORTANT: Leak testing of the appliance shall be conducted as follows:
• After final gas connection is made, turn on manual gas valve and test all
connections in gas supply piping and appliance for gas leaks with a soapy water
solution. During this test all appliance gas valves have to be closed.
• In order to avoid property damage or serious personal injury, never use a lighted
match. If a leak is present, tighten joint or unscrew, apply more joint compound,
tighten again and retest connection for leak.
12

CONVERSION TO LP/PROPANE GAS
Every range is provided with a set of injectors for the various types of gas.
Select the injectors to be replaced according to the "INJECTORS TABLE".
The nozzle diameters, expressed in hundredths of a millimetre, are marked on the
body of each injector.
SETTING THE PRESSURE REGULATOR (fig.2.6)
The pressure regulator is accessible by removing the warmer drawer; the pressure
regulator is positioned on the rear right side of the range (fig. 2.9).
To remove the warming drawer:
1. Open the drawer completely (fig. 2.6)
2. Move down the lever of left guide (fig. 2.7) and up the lever of right guide (fig. 2.8).
3. Remove the drawer; the levers have to be keep moved (fig. 2.6).
Fig. 2.8
2
2
Fig. 2.7 Fig. 2.6
13

_f _='_,%
\
_--_ _e_u_re___
REGULATOR COVER
To set the pressure regulator (fig. 2.9):
1. Unscrew the regulator cover;
2. Unscrew the A component, reverse and screw it according
to the LP/PROPANE regulation.
1Fig. 2.9
2
A
NATURAL GAS
REGULATION LP/PROPANE REGULATION
Fitting the warming drawer (fig. 2.10):
1. Insert the drawer guides into the range guides (fig. 2.10)
2. Gently close the drawer completely; the safety catchs will be automatically hooked.
Fig. 2.10
14

INJECTORS TABLE
NOMINAL
POWER
BURNERS BTU/hr
Auxiliary (AUX) 3500
Semirapid (SR) 6000
Triple ring (TC) 12000
REDUCED LP/PROPANE NATURAL GAS
POWER 11"W.C.R 4" W.C.R
BTU/hr {3 injector By-pass O injector By-pass
[1/100 ram] [1/100mm] [1/100 mm] [1/100mm]
1000 55 27 90 adjustable
1500 72 32 118 adjustable
5000 102 65 170 adjustable
OPERATIONS TO BE PERFORMED WHEN SUBSTITUTING
THE INJECTORS
,/ Remove the gratings, the burner covers and the knobs;
,/ Using a wrench substitute the nozzle injectors "J" (figs. 2.11 - 2.12) with those most
suitable for the kind of gas for which it is to be used.
The burner are conceived in such a way so as not to require the regulation of the
primary air.
SETTING THE BURNER MINIMUM
When switching from one type of gas to another, the minimum flow rate must also be
correct: the flame should not go out even when passing suddenly from maximum to
minimum flame.
To regulate the flame follow the instructions below:
- Light the burner
- Set the gas valve to LO position
- Remove the knob
- With a thin screwdriver pass by the hole of microswitch and turn the screw F until
adjustment is correct (fig. 2.13).
Fig. 2.13
For LP/PROPANE gas, tighten the adjustment screws completely.
After regulation repeat the operations indicated in paragraph "2. Pressure regulator" at
page 9 and 12. Ifthe range has been disconnected and then connected again to the gas
supply line repeat the operations indicated in paragraph "5. Leak Testing" at page 12.
IMPORTANT:
After conversion to LP/PROPANE gas has been carried out affix on the back of the
appliance, near the data plate, the conversion label supplied and also affix a conversion
label at page 3 of this instruction manual. 15

electrical connection
If codes permit and a separate ground wire is used, it is recommended that a qualified
electrician installer determine that the ground path and wire gauge are in accordance
with local codes.
Be sure that the electrical connection and wire size are adequate and in conformance
with:
- ANSl/NFPA 70 latest edition and local codes and ordinances
- CSA Standard C22.1, Canadian Electrical Code, Part 1 - latest edition, and all local
codes and ordinances.
•Do not ground to a gas pipe.
• Check with a qualified electrical installer if you are not sure the range is properly
grounded.
• Do not have a fuse in the neutral or ground circuit.
• When a 4-wire, single phase 120/240-volt, 60Hz, AC-only electrical supply is avail-
able, a 20 amp maximum circuit protection is required, fused on both sides of the
line.
• A time-delay fuse or circuit breaker is recommended.
• This range is equipped with a Certified Power Cord intended to be plugged into
a standard 14-50R wall receptacle. Be sure the wall receptacle is within reach of
range's final location.
• Do not use an extension cord.
Electrical Shock Hazard
Electrically ground range.
Failure to follow these instruc-
tions can result in death, fire or
electrical shock.
In the case of substitution of the power cord always replace it with a suitable UL or CSA
approved one (with the same technical features of the replaced cord).
Tighten the power cord by using only the power cord strain relief bracket supplied with
the appliance. Allow enough slack to easily attach the cord terminals to the terminal
block.
These operations must be carried out only by an authorized technician.
standard NEMA 14-50R wall receptacle
Power supply cord with
NEMA 14-50P plug
16

O:
m
r_
zI-_ °:
[ [
I I
I
J
I
17

AVERTISSENIENT
,, TOUS LES TYPES DE CUISINli_RE
PEUVENT BASCULER
,, CELA PEUT PROVOQUER DES BLESSURES
,, INSTALLEZ LE DISPOSITIF
ANTIBASCULEMENT FOURNI AVEC LA
CUISINli_RE
eCONSULTEZ LES iNSTRUCTiONS
D'INSTALLATION
AVIERTISSlEMIENT : SI L'INFORMATION CONTENUE DANS CE
MANUEL N'EST PAS SUIVIE ALA LETTRE, UN INCENDIE OU
UNE EXPLOSION PEUVENT SE PRODUIRE ET ENTRA/NER DES
DOMMAGES MATI_RIELS, DES BLESSURES OU MEME LA MORT.
INe rangez #as et n'utilisez pas d'essence ou d'autres vapeurs et
liquides inflammables & proximit6 de cet appareil ou de tout autre
appareil 61ectrom6nager.
/QUOI FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ :
• N'essayez pas d'allumer un appareil quel qu'il soit.
° Ne touchez & aucun interru#teur 61ectrique. N'utilisez aucun tel6-
phone de votre domicile.
• Appelez immediatement votre fournisseur de gaz depuis le tel6-
phone d'uq voIs n.
Suivez les instructions de votre fournisseur de gaz.
• Si vous ne pouvez joindre votre fournisseur de gaz, appelez les
pompiers.
,/ Uinstallation, a=nsi que toute r6paration, doivent 6tre effectuees par
un installateur ou une entreprise de service qualifies, ou par le four-
nisseur de gaz.
18
Cet appareil a et6 con?u et fabrique uniquement pour la cuisson domestique des aliments et
ne convient pas & I'usage non menager. Cet appareil ne devrait donc pas _tre utilise dans un
environnement commercial.
La garantie de I'appareil sera annulee s'il est utilise dans un environnement non domestique,
c'est-&-dire un environnement semi-commercial, commercial ou communautaire.

PLAQUE SIGNALFtTIQUE FtTIQUETTE DE CONVERSION
IMPORTANT - VEUILLEZ LIRE ET SUIVRE
v" Avant de commencer, veuillez lire attentivement toutes les instructions.
,/ N'enlevez pas les etiquettes, plaques ou avertissements permanents de
I'appareil. Cela pourrait annuler la garantie.
,/ Veuillez respecter tousles codes et les r_glements Iocaux et nationaux.
,/ Veuillez vous assurer que cet appareil est bien mis & la terre.
v" La prise de courant devrait 6tre toujours accessible.
v" L'installateur doit confier ces instructions au consommateur qui les ®
conservera pour I'usage de I'inspecteur local et pour s'y reporter
ult_rieurement.
L'installation doit _tre conforme aux codes Iocaux, ou en I'absence de ceux-ci, & la derni_re edition du National
Fuel Gas Code ANSIZ223.1. L'installation electrique doit 6tre conforme & la derni_re edition du Code national de
I'electricit6, ANSI/NFPA70 et/ou aux codes Iocaux. AU CANADA : L'installation doit 6tre conforme au CAN/CGA-
B149.1, Code d'installation du gaz naturel ou au CAN/CGA-B149.2, Code d'installation du propane en vigueur
et/ou aux codes Iocaux. L'installation electrique doit 6tre conforme au Code canadien de I'electricit6 CSA C22.1,
partie 1, en vigueur et/ou aux codes Iocaux.
INSTALLATION DANS UNE MAISON PREFABRIQUEE (MOBILE) • L'installation doit 6tre conforme au Manufactured
Home Construction and Safety Standard, Titre 24 CFR, Partie 3280 (anciennement le Federal Standard for Mobile
Home Construction and Safety, Titre 24, HUD/Partie 280) ou, Iorsque cette norme n'est pas applicable, au Standard
for Manufactured Home Installations, ANSI/NCSBCS A225.1, ou aux codes Iocaux, I& oQ il y a lieu.
INSTALLATION DANS UNE CARAVANE DE PARC : L'installation doit 6tre conforme aux codes de I'€:tat ou aux
autres codes ou, en I'absence de tels codes, au Standard for Recreational Park Trailers, ANSI A119.5.
L'installation de tout appareil au gaz doit 6tre effectuee par un technicien qualifi& Par mesure de securite et pour
faciliter le service, un robinet d'arr6t de gaz manuel doit 6tre installe dans le tuyau d'alimentation en gaz, juste
avant I'appareil.
Si vous utilisez une source d'alimentation electrique ext@ieure, cet appareil doit 6tre, au moment de son installa-
tion, mis & la terre conformement aux codes Iocaux en vigueur ou, en I'absence de tels codes, conformement au
Code national de I'electricite, ANSI/NFPA 70.
I,ik L'INTENTION DE L'INSTALLATEUR SEULEMENT I
I CETTE CUISINII RE EST RI SERVI E ,& L'USAGE I
IRI SlDENTIEL UNIQUEMENT. I19

AVERTISSEMENT!
CET APPAREIL DOlT ETRE INSTALLI_ PAR UN INSTALLATEUR QUALIFII_.
Une mauvaise installation, modification, r_paration ou un mauvais reglage ou entretien peuvent causer des blessures ou
des dommages materiels. Consultez un installateur qualifi_, un agent autoris_ ou le fournisseur de gaz.
IMPORTANT : L'utilisation de v_tements et de gants de protection est recommand_e lots de la manutention et I'installation
de cet appareil.
OUTILS REQUIS POUR UINSTALLATION (NON FOURNISAVECL'APPAREIL)
Tournevis
Marteau
J_L
Clef &
poignee en T
Clef &
molette
Crayon M_tre & Crayon ruban
Perceuse
20