Fisher & Paykel HC60BCXB2 Wiring diagram

Box wall cooker hood
HC60BCXB2, HC90BCXB2,
and HC120BCXB2 models
GB IE
INSTALLATION INSTRUCTIONS
USER GUIDE

1
CONTENTS
Introduction 3
Safety and warnings 4
Installation instructions 7
About your cooker hood – Energy efficiency 17
Operating instructions 18
Cleaning and maintenance 19
Parts and accessories 21
Manufacturer’s Warranty 22
Customer Care 23
ImpORTANT!
SAVE THESE INSTRUCTIONS
The models shown in this user guide may
not be available in all markets and are
subject to change at any time. For current
details about model and specification
availability in your country, please go to
our website www.fisherpaykel.com or
contact your local Fisher & Paykel dealer.
Registration
Register your product with us so we can
provide you with the best service possible.
To register your product visit our website:
www.fisherpaykel.com

3
INTRODUCTION
Thank you for purchasing a Fisher & Paykel product.
Thousands of hours go into the design, engineering, testing and perfecting of each
Fisher & Paykel appliance. The care and attention given to creating these beautiful
products doesn’t stop once it has found its home with you.
This use and care manual will answer most of your questions about the set-up, use and
on-going maintenance of your Fisher & Paykel product; however if you require further
information about your product and its use please consult our website for solutions
and further contact information to discuss with a service representative.
To ensure you receive all relevant product updates and the best service possible,
please register your Fisher & Paykel products through our website.

4
SAFETY AND WARNINGS
!WARNING!
13.5 kg
(HC60)
21.5 kg
(HC90)
26 kg
(HC120)
Weight Hazard
The cooker hood is heavy. Please ensure
adequate care is taken when installing the
cooker hood to prevent personal injury. The
cooker hood must be installed onto a solid
wall, stud, beam or truss. Weight of the
product is 13.5 kg (HC60)/ 21.5 kg (HC90)/
26 kg (HC120).
!WARNING!
Electric Shock Hazard
Always disconnect the appliance from the
mains power supply before carrying out any
maintenance or repairs. Alterations to the
domestic wiring system must only be made
by a qualified electrician. Failure to follow this
advice may result in electrical shock or death.
IMPORTANT SAFETY INSTRUCTIONS
WARNING!
When using this appliance always exercise basic
safety precautions including the following:
• Please read the entire set of instructions before
installing the cooker hood.
• Ducting accessories are not supplied. All ducting must
comply with local requirements and building codes.
• Before connecting any pipes, consult municipal
ordinances to ensure that any applicable regulations
concerning the discharge of exhaust air are adhered

5
SAFETY AND WARNINGS
to and request permission from the person in
charge of the building.
• Exhaust air must not be discharged into a flue
that is used for exhausting fumes from appliances
burning gas or other fuels.
• There shall be adequate ventilation of the room
when the cooker hood is used at the same time
asappliances burning gas or other fuels.
• The minimum distance between the supporting
surface for cooking vessels on the hob and the
lowest part of the cooker hood shall be 600mm,
or 650mm if installed over a gas hob.
• Stainless steel is very easily damaged during
installation if abraded or knocked by tools. It is
recommended to protect the top of the cooker hood
with cardboard or polystyrene during the installation
to minimise the risk of damage occurring.
• To reduce the risk of damage occurring to the hob,
it is recommended that the surface of the hob is
protected with cardboard or a similar object during
installation of the cooker hood.
• Attention should be given to ensure that any
applicable regulations concerning the discharge
ofexhaust air are fulfilled.
• To comply with electrical safety regulations, the
cooker hood must be plugged into a socket near
the appliance. The socket must be accessible, or
have an accessible isolating switch, to enable the
end user to isolate the cooker hood from the power
for the purpose of internal cleaning or maintenance.
• A power outlet should be within 750mm of the
motor assembly and can be either on the wall,
behind the chimney or in the ceiling.

6
SAFETY AND WARNINGS
• Always switch the power off prior to installation,
servicing or cleaning the cooker hood.
• If the supply cord of this equipment is damaged
it must only be replaced by the manufacturer, its
service agent or similarly qualified person in order
toavoid a hazard.
• This appliance can be used by children aged from
8years or above and persons with reduced physical,
sensory or metal capabilities or lack of experience
or knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way
and understand the hazards involved. Children shall not
play with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
• You must read the details concerning the method and
frequency of cleaning.
• There is a fire risk if cleaning is not carried out in
accordance with the instructions.
• Never leave frying food unattended since grease
can overheat and catch fire. The risk of fire is even
greater in the case of used oil.
• Do not flambé under the cooker hood.
• Never use the cooker hood without the filters in place.
• During climatic conditions causing electrical
interference, it is possible that the device may stop
working. By switching the device off and on the
device will resume normal operation safety.
• During an electrostatic discharge (ESD) it is possible
that the device will stop working. By switching the
device off and on the device will again work as
intended. There will be no risk of hazard presenting
in the product.
• CAUTION: Accessible parts may become hot when
used with cooking appliances.

7
INSTALLATION INSTRUCTIONS
Contents of packaging
Upper chimney bracket
(1)
Installation instructions
User guide manual
(1)
Chimney
(1)
Expansion plug
(8)
30mm self
tapping screw
(8)
Upper chimney
(1)
Cooker hood
(1)
Ducting adapter
(150mm Ø)
(1)
Chimney bracket
(1)
Box wall cooker hood
HC60BCXB2, HC90BCXB2,
and HC120BCXB2 models
GB IE
INSTALLATION INSTRUCTIONS
USER GUIDE
10mm self
tapping screw
(4)

8
INSTALLATION INSTRUCTIONS
Product dimensions
GF
B
A
max
A
min
E D
K
L
C
I
H
Power cord location
ØJ

9
INSTALLATION INSTRUCTIONS
HC60BCXB2 HC90BCXB2 HC120BCXB2
PRODUCT DIMENSIONS mm
AOverall height of product 595 – 1035 595 – 1035 595 – 1035
BOverall width of product 598 898 1198
COverall depth of product 500 500 500
DHeight of hood 55 55 55
EHeight of stainless strip 27 27 27
FWidth of flue 320 320 320
GDepth of flue 290 290 290
HDistance from centre of ducting
outlet to back of product 105 105 105
IDistance from centre of ducting
outlet to side of flue 160 160 160
JDiameter of ducting outlet 150 150 150
KDistance between centre of lights 230 230 230
LDistance from centre of lights to
back of product 45 45 45
Length of power cord 1500 1500 1500
ImpORTANT!
Actual product dimensions may vary by ± 2mm.
GF
B
A
max
A
min
E D
K
L
C
I
H
Power cord location
ØJ

10
INSTALLATION INSTRUCTIONS
Height of cooker hood
N
M
INSTALLATION DIMENSIONS mm
MInstallation height
Ducted
Recirculation
min. 635 – max. 1035
min. 675 – max. 1035
NHeight top of hob to base of product
Electric hob
Gas hob
min. 600 – max. 750
min. 650 – max. 750

11
INSTALLATION INSTRUCTIONS
Venting options
Attention should be given to ensure that any applicable regulations concerning the
discharge of exhaust air are fulfilled.
The cooker hood can be installed to operate with the exhaust air ducted externally from
the kitchen, or installed to operate with the exhaust air recirculating within the kitchen.
Ducted
For ducted installation it is recommended that 150mm diameter, rigid or semi-rigid
ducting is used. This will require a 160mm (min) round hole in the ceiling or wall.
Careshould be taken to position the hole correctly.
For optimal efficiency, use rigid or semi-rigid ducting for reduced noise and increased
airflow. Flexible ducting should only be used as a last resort (ie in difficult installations)
and if used, ensure that it is pulled tight.
Recirculating
To enable the product to operate with the air recirculating, please purchase a
recirculation diverter and carbon filters (refer to the ‘Parts and accessories’ section).
Therecirculation diverter is required to channel the air out the side vents at the top
ofthe flue and the carbon filters are required to remove odours.
Note: a ducting hole is not required in the wall or ceiling if the cooker hood is
installed to operate with exhaust air recirculating.

12
INSTALLATION INSTRUCTIONS
Installation
WARNING!
This product is heavy and requires two persons for installation.
WARNING!
Failure to install the screws or fixing device in accordance with these instructions may
result in electrical hazards.
The manufacturer is not liable for any damage caused by not following these instructions.
1Preparing for installation:
Before installing your cooker hood:
 Please read the instructions carefully.
 Unpack the cooker hood and check that all functions are working.
 Ensure that the voltage (V) and the frequency (Hz) indicated on the serial plate
match the voltage and frequency at the installation site.
 Check that the area behind the installation surface to be drilled is clear of any
electrical cables or pipes, etc.
 The stainless steel and glass surfaces of the cooker hood are very easily damaged
during installation if grazed or knocked by tools. Please take care to protect the
surfaces during installation.
 Protect the hob surface below with cardboard, or the like, to prevent damage
occurring whilst the cooker hood is being installed above.
 Temporarily mark the height of the bottom of the cooker hood and the centre of the
hob on the wall according to the information given in the ‘Installation instructions –
Height of cooker hood’ section.
 The wall used for mounting the cooker hood should have sufficient strength and a
flat surface.
2Attach chimney brackets and hood mounting screws
 Attach the chimney bracket and upper
chimney bracket (if using the upper chimney)
in the locations shown in Fig.2 and 3. Use
the 30mm screws and expansion plugs if
attaching to masonry.
 Attach the upper hood mounting screws
in the locations shown in Fig.2 and 3. Use
the 30mm screws and expansion plugs if
attaching to masonry. Ensure that there is a
2mm gap between the screw head and the
wall – see Fig.1.
2 mm
Fig.1

13
INSTALLATION INSTRUCTIONS
Fig.2
250 mm
20 mm
A
B
250 mm
235 mm
C
D
Upper chimney extension
bracket attachment points
Chimney bracket
attachment points
Upper hood
attachment points
Lower hood
attachment points
HC60BCXB2 HC90BCXB2 HC120BCXB2
mm
A420 580 900
B559 559 556
C286 286 288
D36 36 42.5

14
INSTALLATION INSTRUCTIONS
Fig.3
3Attach ducting adapter
 Place the ducting adapter
onto the hood and screw it in
place using the 10mm screws.

15
INSTALLATION INSTRUCTIONS
4Attach hood to wall
 Remove filters and easy clean plate from hood as shown in Fig.4.
Fig.4

16
INSTALLATION INSTRUCTIONS
Fig.5
 Hang hood off upper hood mounting screws with 2mm gap. Hang off the keyhole
attachment points on the back of the hood (see Fig.5). Tighten screws.
 Attach lower hood mounting screws to fix hood to wall.
 Reattach easy clean plate and filters.
5Attach ducting
 Attach ducting to ducting adapter and vent outside.
6Attach chimney
 Place chimney around the hood chassis and attach to the chimney bracket.
 Extend the upper chimney and attach to the upper chimney bracket with 10mm
screws (if using upper chimney).

17
ABOUT YOUR COOKER HOOD – ENERGY EFFICIENCY
Product Fiche
EN61591
MODEL
HC60BCXB2
HC90BCXB2
HC120BCXB2
Annual Energy Consumption (kWh/annum) 26
Time Increase Factor 0.8
Energy Efficiency Index 44.8
Energy Efficiency Class A+
Fluid Dynamic Efficiency 33.1
Fluid Dynamic Efficiency Class A
Lighting Efficiency 36
Lighting Efficiency Class A
Grease Filtering Efficiency 91.2
Grease Filtering Efficiency Class B
Airflow at Min. Speed (m³/hr) 200
Airflow at Max. Speed (m³/hr) 525
Airflow at Boost Speed (m³/hr) 710
Airborne noise at minimum (dB) 40
Airborne noise at maximum (dB) 64
Airborne noise at Boost (dB) 67
Airflow At Best Efficiency Point (m³/hr) 344.8
Electrical Power Input At Best Efficiency Point (W) 70.8
Lighting Nominal Power (W) 7
Lighting Average Illumination (lux) 252
Power consumption in Off mode (W) 0.41
Power consumption in Standby mode (W) 0.41

18
OPERATING INSTRUCTIONS
Touch control panel
CONTROL PANEL FEATURES
Power on/off Turn the cooker hood on or off. The fan
automatically turns on to operate at level 1.
Fan speed 1 – 4 Adjust the fan speed levels from 1 – 4 with 1
being the lowest level and 4 being the highest.
The fan speed level icon illuminates red when
selected.
Boost Turn the fan onto boost speed. The icon
flashes red when it is on. The cooker hood will
operate on boost speed for 5minutes and will
then revert to speed 4.
Timer Turn the timer on. The fan operates for
5minutes at the current speed and each
descending speed before turning off.
The timer icon flashes red when the filters
need cleaning. To reset the timer press the
button and it will stop flashing and begin
counting again.
Lights on/off Turn the lights on or off. The lights turn on to
the last level selected.
Reduce
lighting level
Press once to adjust the light to the lowest
level. The icon illuminates red when on the
lowest level. Press and hold to progressively
dim the light level.
Increase
lighting level
Press once to adjust the light to the highest
level. The icon illuminates red when on the
highest level. Press and hold to progressively
increase the light level.