Fisher & Paykel HP60ICSX3 User manual

BUILT-IN INTEGRATED
RANGEHOOD
HP60ICSX and HP90ICSX models
INSTALLATION GUIDE / USER GUIDE
NZ AU

1
CONTENTS
IMPORTANT!
SAVE THESE INSTRUCTIONS
The models shown in this user guide may
not be available in all markets and are
subject to change at any time. For current
details about model and specification
availability in your country, please go to
our website fisherpaykel.com or contact
your local Fisher & Paykel dealer.
Registration
Register your product with us so we can
provide you with the best service possible.
To register your product visit our website:
fisherpaykel.com
Safety and warnings 3
Installation instructions 5
Operating instructions 13
Cleaning and maintenance 14
Parts and accessories 16
Service & Warranty 17

3
SAFETY AND WARNINGS
! WARNING!
8.5 kg
(HP60)
9.5 kg
(HP90)
Weight Hazard
The appliance is heavy. Please ensure adequate care is taken when
installing the appliance to prevent personal injury. The appliance must be
installed onto a solid wall, stud, beam or truss. Weight of the product is
8.5 kg (HP60)/ 9.5 kg (HP90).
! WARNING!
Electric Shock Hazard
Always disconnect the appliance from the mains power supply before
carrying out any maintenance or repairs. Alterations to the domestic wiring
system must only be made by a qualified electrician.
Failure to follow this advice may result in electrical shock or death.
IMPORTANT SAFETY INSTRUCTIONS
WARNING!
When using this appliance always exercise basic safety precautions including
thefollowing:
 Read the entire set of instructions before installing or using this appliance.
 Please make this information available to the person installing the appliance –
doingso could reduce your installation costs.
 Always switch the power off prior to installation, servicing or cleaning of
therangehood.
 This appliance must be installed and connected to the mains power supply only
by a suitably qualified person according to these installation instructions and in
compliance with any applicable local building and electricity regulations. Failure
toinstall the appliance correctly could invalidate any warranty or liability claims.
 To comply with electrical safety regulations, the rangehood must be plugged into
a socket near the appliance. The socket must be accessible, or have an accessible
isolating switch, to enable the end user to isolate the rangehood from the power for
the purpose of internal cleaning or maintenance.
 A power outlet should be within 750 mm of the motor assembly and can either be
onthe wall, behind the chimney or in the ceiling.
 If the supply cord of this equipment is damaged, it must only be replaced by the
manufacturer, its service agent or similarly qualified person in order to avoid a hazard.
 Ducting accessories are not supplied. All ducting must comply with local requirements
and building codes.
 Attention should be given to ensure that any applicable regulations concerning the
discharge of exhaust air are fulfilled.

4
SAFETY AND WARNINGS
 Before connecting any pipes, consult municipal ordinances to ensure that any
applicable regulations concerning the discharge of exhaust air are adhered to and
request permission from the person in charge of the building.
 Exhaust air must not be discharged into an existing flue that is used for exhausting
fumes from appliances burning gas or other fuels.
 There shall be adequate ventilation of the room when the rangehood is used at the
same time as appliances burning gas or other fuels.
 The minimum distance between the supporting surface for cooking vessels on the
cooktop and the lowest part of the rangehood shall be 600 mm or 650 mm ifinstalled
over a gas cooktop.
 Stainless steel is very easily damaged during installation if abraded or knocked by
tools. It is recommended to protect the top of the rangehood with cardboard or
polystyrene during the installation to minimise the risk of damage occurring.
 To reduce the risk of damage occurring to the cooktop, it is recommended that
the surface of the cooktop is protected with cardboard or a similar object during
installation of the rangehood.
 This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning the use of the appliance
by a person responsible for their safety.
 Children should be supervised to ensure they do not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
 You must read the details concerning the method and frequency of cleaning.
 There is a fire risk if cleaning is not carried out in accordance with the instructions.
 Never leave frying food unattended since grease can overheat and catch fire.
The risk of fire is even greater in the case of used oil.
 Do not flambé under the rangehood.
 Never use the rangehood without the filters in place.
 During an electrostatic discharge (ESD) it is possible that the device will stop
working. By switching the device off and on the device will again work as intended.
 CAUTION: accessible parts may become hot when used with cooking appliances.
 Remove all packaging, including protective wrappings, before use.

5
INSTALLATION INSTRUCTIONS
Contents of packaging
13mm screw
(2)
Installation guide /
User guide
(1)
Rangehood
(1)
BUILT-IN INTEGRATED
RANGEHOOD
HP60ICSX2 and HP90ICSX2 models
INSTALLATION GUIDE / USER GUIDE
NZ AU
125mm ducting adapter
with non return flap
(1)

INSTALLATION INSTRUCTIONS
6
Product and cabinetry cutout dimensions
F
C
(
A)A
D
O
B
E
G
I
H
J
K
ØL
N
M
HP60
Power cord location
HP90
Power cord location

INSTALLATION INSTRUCTIONS
7
HP60ICSX3 HP90ICSX3
PRODUCT DIMENSIONS mm mm
AOverall height of product
(with ducting adapter)
325
(404)
260
(330)
BOverall width of product 492 792
COverall depth of product 277 277
DThickness of flange 1 1
EWidth of chassis 450 750
FDepth of chassis 255 255
GHeight of side of chassis n/a 100
HWidth of top surface of chassis 265 250
ILength of angled surface of chassis 335 273
JDistance from centre of ducting outlet
toback of chassis 82 73
KDistance from centre of ducting outlet
toside of chassis 225 375
LDiameter of ducting outlet 125 125
MDistance between centre of lights 340 385
NDistance from centre of light to front
ofproduct 45 45
Length of power cord 950 950
CABINETRY CUTOUT DIMENSIONS
Overall width of cutout 460 760
Overall depth of cutout 260 260
OBase of brackets/clips to bottom of chassis min. 15 – max. 35 min. 15 – max. 35
IMPORTANT!
Actual product dimensions may vary by ± 2mm.
Please read the entire instructions before installing the rangehood.

INSTALLATION INSTRUCTIONS
8
Height of rangehood
P
MINIMUM CLEARANCES mm
P
Height top of cooktop to base of product
Electric cooktop
Gas cooktop
min. 600 – max.
recommended 750
min. 650 – max.
recommended 750
This rangehood must be installed no lower than the minimum height indicated in the
table above. Minimum installation height may be greater if required by the cooktop
manufacturer or safety and warnings section on this user guide. Installation at the
minimum height will improve efficiency of capturing cooking odours, grease and smoke.
Installation at the maximum height improves ergonomics by offering increased head
room.

INSTALLATION INSTRUCTIONS
9
Induction cooking considerations
 Induction cooktops use energy efficient technology that only heats the contents of a
cooking pot.
 Unlike gas or traditional electric cooktops, the surrounding air does not get heated
when using an induction cooktop. As a result, rangehood filters, splashbacks and
surrounding cabinetry do not get warmed up, increasing the likelihood of condensation
on these cooler surfaces.
 Other factors like ambient temperature, humidity, natural ventilation of the room, size of
the cookware and how the induction cooktop is being used also influence condensation.
For example, aggressive boiling on high cooktop heat settings like PowerBoost increases
the rate at which water is evaporated, increasing the likelihood of condensation.
 It is important to understand that neither the rangehood nor the induction cooktop are
faulty as a result of this phenomenon.
Condensation can be minimised by:
 Installing the rangehood at the maximum height above the cooktop as specified in
this user guide.
 Using the rangehood on a lower speed setting when boiling.
 Using the induction cooktop on a lower heat setting when boiling.
 Switching the rangehood on 5minutes before cooking and letting it run for at least
5minutes after cooking.
Venting options
Attention should be given to ensure that any applicable regulations concerning the
discharge of exhaust air are fulfilled.
The rangehood can be installed to operate with the exhaust air ducted externally from
the kitchen, or installed to operate with the exhaust air recirculating within the kitchen.
Ducted
For ducted installation it is recommended that 125mm diameter, rigid or semi-rigid
ducting is used. This will require a 135mm (min) round hole in the ceiling or wall. Care
should be taken to position the hole correctly.
For optimal efficiency use the shortest and straightest duct route possible and use rigid
or semi-rigid ducting for reduced noise and increased airflow. Flexible metal ducting
should only be used as a last resort (ie in difficult installations) and if used ensure that it
is straight and smooth and extended as much as possible.
Recirculating
Where ducting outside is not a practical option, this rangehood can be installed to
operate with the air recirculating. Carbon filters are required to remove odours from the
air before it is channelled back into the room or overhead bulkhead (refer to ‘Cleaning
and Maintenance’ section). Ensure that the ducting outlet is not obstructed, even a
partial obstruction will restrict the efficiency of the rangehood.

INSTALLATION INSTRUCTIONS
10
WARNING!
 This appliance is heavy and requires two persons for unpacking and installation
 Installation work and electrical wiring must be done by qualified person(s) in
accordance with all applicable codes and standards.
 Failure to install the screws or fixing device in accordance with these instructions
mayresult in electrical hazards
IMPORTANT!
Wear gloves to protect against sharp edges.
The manufacturer is not liable for any damage caused by not following these instructions.
Installation
1Prepare for installation.
Before installing your rangehood:
 Please read the instructions carefully.
 Unpack the rangehood and check that all functions are working.
 Ensure that the voltage (V) and the frequency (Hz) indicated on the serial plate
match the voltage and frequency at the installation site.
 The stainless steel and glass surfaces of the rangehood are very easily damaged
during installation if grazed or knocked by tools. Please take care to protect the
surfaces during installation.
 Protect the cooktop surface below with cardboard, or the like, to prevent damage
occurring whilst the rangehood is being installed above.
2Fit the 125mm ducting adapter with non return flap to the rangehood using the
screwssupplied.
3Provide an opening on the underside of the cupboard (see product and cabinetry
cutout dimensions).
width
depth
2.3
2.2
2.1
x2

INSTALLATION INSTRUCTIONS
11
4Remove the filter from the rangehood.
5Connect duct and plug rangehood in.
width
depth
2.3
2.2
2.1
x2
width
depth
2.3
2.2
2.1
x2
6Lift the rangehood and fit through the opening of the cupboard till the spring loaded
brackets / clips hold the product in place.

INSTALLATION INSTRUCTIONS
12
7Secure rangehood while tightening the 2 brackets / clips.
width
depth
2.3
2.2
2.1
x2

13
OPERATING INSTRUCTIONS
Control panel
CONTROL PANEL FEATURES
Lights Turn the lights on or off.
Fan Turn the rangehood fan on or off.
Fan speed 1–3 Adjust the fan speed levels from 1 – 3 with 1 being
the lowest level and 3 being the highest.

14
CLEANING AND MAINTENANCE
WARNING!
 Unplug or disconnect the appliance from the power supply before servicing
orcleaning.
 When replacing the bulb, let the bulb cool, and assure that power to the
rangehoodhas been turned off. Use new bulbs according to that indicated
ontherangehood nameplate.
IMPORTANT!
 Never use abrasive or oil based cleaners.
 Wear gloves to protect against sharp edges.
Maintenance
The rangehood should be cleaned regularly using a mild, liquid detergent and a clean
soft cloth to avoid a build-up of grease occurring. Avoid the use of corrosive chemicals,
abrasive cleaning products, hard brushes and steel wool pads. Grease deposits are
corrosive which can cause damage to your rangehood.
Note: in areas of high humidity or coastal environments, cleaning should be carried out
more frequently.
Aluminium filters
 Depending on use, and at least once a
month, the aluminium grease filters should
be removed and cleaned with hot soapy
water or in a dishwasher.
 If washed in a dishwasher, the filters should
be placed in an upright position to prevent
food from falling on them.
 After rinsing and drying, replace the filters.
Note: some discolouration of the frames may occur.
Removing the aluminium filters:
1Pull the relative filter catch, tilting it downwards until it disengages from the supports.
2Reverse these instructions when refitting the filters.
Carbon filters – for use in recirculation mode
Active carbon filters are disposable items designed to remove grease and odours from
cooking vapours before the air is channelled back into the kitchen. The active carbon
filters must be replaced periodically to work properly, at least once every three months,
depending on the frequency with which the rangehood is used.

15
IMPORTANT!
 Carbon filters are disposable items and must be replaced at least every three months.
 Saturated carbon filters can become a barrier to air movement, therefore limiting
your range hoods performance.
 In the event of a fire, grease laden filters could be flammable.
Fitting the carbon filters:
1Ensure the range hood is switched off.
2Remove the aluminum grease filters from the range hood.
3Place a carbon filter on each side of the blower inlet using the keyhole slots for alignment
(refer to A), turn the filter until it clips into place (refer to B).
Note: The direction will be clockwise on one side of the blower and counterclockwise on
the other side of the blower.
4Refit aluminium grease filters.
Light bulb replacement
Note: replacement bulbs are not covered by warranty.
1Remove the aluminium filter.
2Unscrew the light bulb.
3Insert the replacement bulb into the lamp socket.
4Replace the aluminium filter.
CLEANING AND MAINTENANCE
Bulb replacement
BA

16
PARTS AND ACCESSORIES
ITEM REFERENCE NUMBER
LED bulb 792603
Aluminium filter (HP60) 792459
Aluminium filter (HP90) 792427
Recirculation carbon filter x2 791772
150 mm ducting adapter with non return flap 792454

17
SERVICE & WARRANTY
For details of your Manufacturer’s Warranty and contacts for servicing, please refer to
your separate service and warranty book provided with your range hood.
Complete and keep for safe reference:
Model
Serial No.
Purchase Date
Purchaser
Dealer
Suburb
Town
Country

NZ AU
104078D 02.18
FISHERPAYKEL.COM
© Fisher & Paykel Appliances 2018. All rights reserved.
The product specifications in this booklet apply to the specific products
and models described at the date of issue. Under our policy of continuous
product improvement, these specifications may change at any time. You
should therefore check with your Dealer to ensure this booklet correctly
describes the product currently available.