Fisher & Paykel HF60LW4 User manual

Installation instructions
Please read and follow the ‘Safety and warnings’ and ‘installation instructions’ sections carefully before using your
rangehood.
Rangehood (1) Installation instructions
User guide manual (1)
125 mm diameter ducting
adapter (1)
Duct hole cover (1) 10 mm self tapping
screw (2)
https://producthelp.fisherpaykel.com/nz/Cook/Rangehoods/Standard/HF60LW4/User_Guide_HF60LW4/02_Installation_instru…
Updated: Tue, 12 May 2020 02:57:47 GMT
Powered by
1

Product dimensions
Product Dimensions (table)
Property Size (mm)
A. Overall height of product 120
B. Overall width of product 595
C. Overall depth of product 450
https://producthelp.fisherpaykel.com/nz/Cook/Rangehoods/Standard/HF60LW4/User_Guide_HF60LW4/02_Installation_instru…
Updated: Tue, 12 May 2020 02:57:47 GMT
Powered by
2

Property Size (mm)
D. Distance from centre of ducting outlet to back of product 75
E. Distance from centre of ducting outlet to side of product 298
F. Diameter of ducting outlet 125
G. Length of light 385
H. Width of light 55
I. Distance between back of light to back of product 13
J. Depth of top surface of product 340
Length of power cord 900
Actual product dimensions may vary by ± 2 mm.
Please read the entire instructions before installing the rangehood.
Height of rangehood
https://producthelp.fisherpaykel.com/nz/Cook/Rangehoods/Standard/HF60LW4/User_Guide_HF60LW4/02_Installation_instru…
Updated: Tue, 12 May 2020 02:57:47 GMT
Powered by
3

https://producthelp.fisherpaykel.com/nz/Cook/Rangehoods/Standard/HF60LW4/User_Guide_HF60LW4/02_Installation_instru…
Updated: Tue, 12 May 2020 02:57:47 GMT
Powered by
4

Installation Dimensions
Property Size (mm)
K. Height top of cooktop to base of product
•Electric cooktop
•Gas cooktop
min. 600 – max. 750
min. 650 – max. 750
Rangehood installation height above the cooktop is the user’s preference.
Lower installation heights will improve the efficiency of capturing cooking odours, grease,
and smoke. This rangehood must be installed between the minimum and maximum
dimensions indicated in the table above.
Venting options
Attention should be given to ensure that any applicable regulations concerning the discharge of exhaust air are
fulfilled.
The rangehood can be installed to operate with the exhaust air ducted externally from the kitchen, or installed to
operate with the exhaust air recirculating within the kitchen.
Ducted
For ducted installation it is recommended that 125 mm diameter, rigid or semi-rigid ducting is used. This will
require a 135 mm (min) round hole in the ceiling or wall. Care should be taken to position the hole correctly.
For optimal efficiency use the shortest and straightest duct route possible and use rigid or semi-rigid ducting for
reduced noise and increased airflow. Flexible metal ducting should only be used as a last resort (ie in difficult
installations) and if used ensure that it is straight and smooth and extended as much as possible.
Recirculating
To enable the product to operate with the air
recirculating, ensure
the lever on the motor casing under the filter is in the
recirculation position (see Fig.1) and close off the duct
hole with the cover provided (see Fig.2). Purchase and
https://producthelp.fisherpaykel.com/nz/Cook/Rangehoods/Standard/HF60LW4/User_Guide_HF60LW4/02_Installation_instru…
Updated: Tue, 12 May 2020 02:57:47 GMT
Powered by
5

install carbon filters (refer to the ‘Parts and accessories’
section). The rangehood will channel the air out of the
vent on the front surface. The carbon filters are required
to remove odours.
A ducting hole is not
required in the wall or
ceiling if the rangehood is
installed to operate with
exhaust air recirculating.
Fig. 1
Fig. 2
•This product is heavy and requires two persons for installation.
•Installation work and electrical wiring must be done by qualified person(s) in
accordance with all applicable codes and standards.
•Failure to install the screws or fixing device in accordance with these instructions may
result in electrical hazards.
https://producthelp.fisherpaykel.com/nz/Cook/Rangehoods/Standard/HF60LW4/User_Guide_HF60LW4/02_Installation_instru…
Updated: Tue, 12 May 2020 02:57:47 GMT
Powered by
6

Wear gloves to protect against sharp edges.
The manufacturer is not liable for any damage caused by not following these instructions.
Installation
1. Preparing for installation:
Before installing your rangehood:
• Please read the instructions carefully.
• Unpack the rangehood.
• Ensure that the voltage (V) and the frequency (Hz) indicated on the serial plate match the voltage and frequency
at the installation site.
• Check that all functions are working.
• Check that the area behind the installation surface to be drilled is clear of any electrical cables or pipes, etc.
• The rangehood surfaces can be damaged during installation if grazed or knocked by tools. Please take care to
protect the surfaces during installation.
• Protect the cooktop surface with cardboard, or the like, to prevent damage occurring whilst the rangehood is
being installed above.
• Temporarily mark the height of the bottom of the rangehood and the centre of the cooktop on the wall according
to the information given in the ‘Installation instructions – Height of rangehood’ section.
• The wall used for mounting the rangehood should have sufficient strength and a flat surface.
Wall Mounting
1. Attach the rangehood mounting screws to the wall
• Attach the upper rangehood mounting screws in the
locations shown in Fig.4. Use 30 mm screws (and
expansion plugs if attaching to masonry). Ensure
that there is a 2 mm gap between the screw head
and the wall (see Fig.3).
https://producthelp.fisherpaykel.com/nz/Cook/Rangehoods/Standard/HF60LW4/User_Guide_HF60LW4/02_Installation_instru…
Updated: Tue, 12 May 2020 02:57:47 GMT
Powered by
7

Product Dimensions (table continued)
Property Size (mm)
L. Rangehood attachment point width 540
M. Lower rangehood attachment point height 35
N. Upper rangehood attachment point height 103
2. Wall mounting
• Remove the filter – pull the relative catch and tilt the filter downwards until it disengages from the supports (see
Fig.5).
Fig. 5
• Hang the rangehood off the upper rangehood mounting screws with 2 mm gap. Hang off the keyhole attachment
points on the back of the rangehood (see Fig.6) then tighten the screws.
https://producthelp.fisherpaykel.com/nz/Cook/Rangehoods/Standard/HF60LW4/User_Guide_HF60LW4/02_Installation_instru…
Updated: Tue, 12 May 2020 02:57:47 GMT
Powered by
8

Fig. 6
• Attach the lower rangehood mounting screws to fix the rangehood to the wall.
• Refit the filter.
3. Remove packaging
• Remove all packaging and protective wrappings.
Under cupboard mounting
1. Attach the ducting adapter to the rangehood (if ducted)
• Place the ducting adapter onto the hood and screw it in place using 10 mm screws (see Fig.7).
Fig. 7
2. Mount the rangehood
• Remove the filter – pull the relative catch and tilt the filter downwards until it disengages from the supports (refer
to Fig.5).
https://producthelp.fisherpaykel.com/nz/Cook/Rangehoods/Standard/HF60LW4/User_Guide_HF60LW4/02_Installation_instru…
Updated: Tue, 12 May 2020 02:57:47 GMT
Powered by
9

• Attach the rangehood to the cupboard using the mounting holes (refer to Fig.8 below).
• Create additional means of attachment using the extra holes found on top panel of the rangehood. Ensure all
fixings are secure.
• Refit the filter.
Fig. 8
Product Dimensions (table continued)
Property Size (mm)
O. Rangehood attachment point width 540
P. Rangehood rear attachment point 30
Q. Rangehood front attachment point 301
3. Attach ducting (if ducted)
• Attach ducting to the ducting adapter using aluminium duct tape and vent outside.
4. Remove packaging
• Remove all packaging and protective wrappings.
https://producthelp.fisherpaykel.com/nz/Cook/Rangehoods/Standard/HF60LW4/User_Guide_HF60LW4/02_Installation_instru…
Updated: Tue, 12 May 2020 02:57:47 GMT
Powered by
10