Fisher & Paykel HC30DTX1 User manual

US CA
Installation instructions
and User guide (EN)
Hotte aspirante décorative
HC30DTX1 & HC36DTXB1 modèle
Designer canopy
HC30DTX1 & HC36DTXB1 model
Conseils d’installation
et guide d’utilisation (FR)

EN English Page 3 – 13
FR Français Pág 15 – 25

3
Contents
Safety and warnings 4
Installation instructions 6
Four-speed control panel with digital indicator 9
Cleaning and maintenance 10
Limited warranty 11
Important!
SAVE THESE INSTRUCTIONS
The models shown in this User Guide may not be available in all markets and are
subject to change at any time. For current details about model and specification
availability in your country, please visit our website listed on the back cover or
contact your local Fisher & Paykel dealer.
US
CA

4Safety and warnings
Installation instructions
READ AND SAVE THESE INSTRUCTIONS.
WARNING – to reduce the risk of fire, electric shock or injury to persons,
observe the following:
WARNING!
Electrical Shock Hazard
Installation work and electrical wiring must be done by qualified
person(s) in accordance with all applicable codes and standards,
including fire-ratedconstruction.
Read and follow the SAFETY AND WARNINGS outlined in this User Guide
before operating this appliance.
Failure to do so can result in death, electric shock, fire or injury to persons.

Sufficient air is needed for proper combustion and exhausting of gases through the flue
(chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment
manufacturer’s guideline and safety standards such as those published by the National
Fire Protection Association (NFPA), the American Society for Heating, Refrigeration and
AirConditioning Engineers (ASHRAE) and local code authorities.

When cutting or drilling into wall or ceiling, do not damage electrical wiring or other
hiddenutilities.

Ducted fans must always be vented to the outdoors.

Use only metal ductwork.

WARNING: To reduce risk of fire and to properly exhaust air, be sure to duct air outside.
– Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces
orgarages.
Important safety instructions

WARNING: Disconnect the rangehood from power supply before servicing.
WARNING – to reduce the risk of fire, electric shock or injury to persons,
observe the following:

Do not use this fan with any solid state speed control device.

Use this unit only in the manner intended by the manufacturer. If you have questions, contact
the manufacturer. For residential use only.

Before servicing or cleaning unit, switch power off at service panel and lock service panel to
prevent power from being switched on accidentally. When the service disconnecting means
cannot be locked, securely fasten a prominent warning device, such as a tag to the service panel.
US
CA

5
Safety and warnings

CAUTION: For general ventilating use only. Do not use to exhaust hazardous or explosive
materials and vapors.

CAUTION: To reduce the risk of fire, use only metal duct work.
WARNING – to reduce the risk of a range top grease fire:

Never leave surface units unattended at high settings. Boilovers cause smoking and greasy
spillovers that may ignite. Heat oils slowly on low or medium settings.

Always turn hood on when cooking at high heat or when flambeing food (i.e. Crepes Suzette,
Cherries Jubilee, Peppercorn Beef Flambé).

Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.

Use proper pan size. Always use cookware appropriate for the size of the surface element.
WARNING – to reduce the risk of injury to persons in the event of a range top
grease fire, observe the following:

Smother flames with a close-fitting lid, cookie sheet or metal tray, then turn off the burner.
Becareful to prevent burns. If the flames do not go out immediately, evacuate and call the
firedepartment.

Never pick up a flaming pan – you may be burned.

Do not use water, including wet dishclothes or towels – a violent steam explosion will result.

Use an extinguisher only if:
– You know you have a Class ABC extinguisher, and you already know how to operate it.
– The fire is small and contained in the area where it started.
– The Fire Department is being called.
– You can fight the fire with your back to an exit.
WARNING – sufficient air is needed for proper combustion and exhausting of gases through
the flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating
equipment manufacturer’s guidelines and safety standards such as those published by National
Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air
Conditioning Engineers (ASHRAE) and local code authorities.
The manufacturer declines all liability in cases where the instructions for the appropriate
installation, maintenance and use of the extractor hood are not observed.
US
CA

6Installation instructions
Decorative extractor hoods
Dear client:
We are sure that the purchase of our rangehood
will fully satisfy all of your needs. Please read this
instruction manual carefully in order to obtain the best
results from the use of the hood.
Important

Proof of purchase is required before a warranty claim
will beaccepted.
General indications

Before installing and using the hood, be sure
that the voltage (V) and the frequency (Hz)
indicated on the feature plate match the voltage
and frequency at the installation site.

The feature plate and technical data are shown
on the inside of theproduct.

This hood is equipped with an adjustable
chimney cover which allows it to be adjusted to
the height of the ceiling.
Wall mounting
1 Please remove the polyfoam protection piece
(from behind the motor) beforeuse.
2 Connect the outlet adapter supplied with
the hood (6“diameter) to an exhaust duct
connected directly to the outside (Fig.2).
3 Screw on the connection box following (Fig.2a)
with the two /” x /” screws supplied in the
box ofaccessories.
4 The accessories needed to install the hood are
inside thehood.
5 Drill holes in the wall using a ⁄” drill bit.
6 The anchors and screws needed to hang the
hood are contained in the bag of accessories
supplied with thehood.
7 This fan shall be mounted a minimum of 22“
above the heat source.
Fig.1 HC36DTXB1 Designer canopy illustrated
Fig.2 Connect the outlet adapter to the exhaust duct
Fig.2a
US
CA

7
Installation instructions
Electrical connection
Important!
Be certain all wiring complies with local codes and the unit is properly grounded.
1 Run three wires, two for the power supply and the ground wire, from the connection box on the
canopy to a power connection point near the installation.
2 Using approved wiring connectors, connect the power conductors to the conductors for the fan:
black to black and white to white.
3 Connect the grounding wire (green or bare) to the Ground conductor (green) of the fan
distribution box.
US
CA

8Installation instructions
Assembly of chimney cover
1 Mark the wall at the location of support C (Fig.4a) according to the heights and specifications
shown on the mountingtemplate.
2 Drill holes in the wall, place anchors in the holes and attach support C with screws (Fig.4a).
3 Place tube A with the extendible part B hanging on the inside, making sure that flange D is
correctly lodged in the support
C (Fig.4a).
4 Next, secure support E to the upper end of the wall, making sure that it is properly aligned with
the extendible tube. Extend the movable part of tube
B until it reaches support E and connect
to the support with the two side screws
F (Fig.4b).
B
E
Fig.4bFig.4a
A
B
E
C
D
F
Fig.4 Assembly of chimney cover
Fig.3 Mounting template
US
CA