Fisher & Paykel HF60LX4 Wiring diagram

Standard Rangehood
HF60LX4 and HF60LW4 model
NZ AU
INSTALLATION INSTRUCTIONS
USER GUIDE

1
CONTENTS
Safety and warnings 3
Installation instructions 5
Operating instructions 13
Cleaning and maintenance 14
Parts and accessories 16
Manufacturer’s Warranty 17
Customer Care 19
IMPORTANT!
SAVE THESE INSTRUCTIONS
The models shown in this user guide may
not be available in all markets and are
subject to change at any time. For current
details about model and specification
availability in your country, please go to
our website www.fisherpaykel.com or
contact your local Fisher & Paykel dealer.
Registration
Register your product with us so we can
provide you with the best service possible.
To register your product visit our website:
www.fisherpaykel.com

3
SAFETY AND WARNINGS
!WARNING!
4.8 kg
(HF60)
Weight Hazard
The rangehood is heavy. Please ensure adequate care is taken when
installing the rangehood to prevent personal injury. The rangehood must
be installed onto a solid wall, stud, beam or truss. Weight of the HF60
is4.8 kg.
!WARNING!
Electric Shock Hazard
Always disconnect the appliance from the mains power supply before
carrying out any maintenance or repairs. Alterations to the domestic
wiring system must be made by a qualified electrician.
Failure to follow this advice may result in electric shock or death.
IMPORTANT SAFETY INSTRUCTIONS
WARNING! When using this appliance always exercise basic safety precautions including
the following:
 Please read the entire set of instructions before installing or using this appliance.
 Please make this information available to the person installing the appliance –
doing so could reduce your installation costs.
 Always switch the power off prior to installation, servicing or cleaning
oftherangehood.
 This appliance must be installed and connected to the mains power supply only by a
suitably qualified person according to these installation instructions and in compliance
with any applicable local building and electricity regulations. Failure to install the
appliance correctly could invalidate any warranty orliability claims.
 To comply with electrical safety regulations, the rangehood must be plugged into
a socket near the appliance. The socket must be accessible, or have anaccessible
isolating switch, to enable the end user to isolate the rangehood from the power for
thepurpose of internal cleaning or maintenance.
 A power outlet should be within 750 mm of the motor assembly and can either be on
the wall, behindthe chimney or in the ceiling.
 If the supply cord of this equipment is damaged, it must only be replaced by the
manufacturer, its service agent or similarly qualified person in order toavoid a hazard.
 Ducting accessories are not supplied. All ducting must comply with local requirements
and building codes.
 Attention should be given to ensure that any applicable regulations concerning the
discharge of exhaust air are fulfilled.
 Before connecting any pipes, consult municipal ordinances to ensure that any
applicable regulations concerning the discharge of exhaust air are adhered to and
request permission from the person in charge of the building.
 Exhaust air must not be discharged into an existing flue that is used for exhausting
fumes from appliances burning gas or other fuels.

4
SAFETY AND WARNINGS
 There shall be adequate ventilation of the room when the rangehood is used at the
same time as appliances burning gas or other fuels.
 The minimum distance between the supporting surface for cooking vessels on the
cooktop and the lowest part of the rangehood shall be 600 mm or 650 mm if installed
over a gas cooktop.
 Stainless steel is very easily damaged during installation if abraded or knocked by
tools. It is recommended to protect the top of the rangehood with cardboard or
polystyrene during the installation to minimise the risk of damage occurring.
 To reduce the risk of damage occurring to the cooktop, it is recommended that
the surface of the cooktop is protected with cardboard or a similar object during
installation of the rangehood.
 This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning the use of the appliance
bya person responsible for their safety.
 Children should be supervised to ensure they do not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
 You must read the details concerning the method and frequency of cleaning.
 There is a fire risk if cleaning is not carried out in accordance with the instructions.
 Never leave frying food unattended since grease can overheat and catch fire. The risk
of fire is even greater in the case of used oil.
 Do not flambé under the rangehood.
 Never use the rangehood without the filters in place.
 During an electrostatic discharge (ESD) it is possible that the device will stop working.
By switching the device off and on the device will again work as intended.
 CAUTION: accessible parts may become hot when used with cooking appliances.
 Remove all packaging, including protective wrappings, before use.

5
INSTALLATION INSTRUCTIONS
Contents of packaging
10mm self tapping screw
(2)
Installation instructions
User guide manual
(1)
125 mm diameter
ducting adapter
(1)
Duct hole cover
(1)
Rangehood
(1)
Standard Rangehood
HF60LX4 model
NZ AU
INSTALLATION INSTRUCTIONS
USER GUIDE

6
INSTALLATION INSTRUCTIONS
Product dimensions
PRODUCT DIMENSIONS mm
AOverall height of product 120
BOverall width of product 595
COverall depth of product 450
DDistance from centre of ducting outlet to back of product 75
EDistance from centre of ducting outlet to side of product 298
FDiameter of ducting outlet 125
GLength of light 385
HWidth of light 55
IDistance between back of light to back of product 13
JDepth of top surface of product 340
Length of power cord 900
IMPORTANT!
Actual product dimensions may vary by ± 2 mm.
Please read the entire instructions before installing the rangehood.
A
b
d
g
H
c
Power cord
FØ
e
I
J
J

7
INSTALLATION INSTRUCTIONS
Height of rangehood
INSTALLATION DIMENSIONS mm
KHeight top of cooktop to base of product
Electric cooktop
Gas cooktop
min. 600 – max. 750
min. 650 – max. 750
Rangehood installation height above the cooktop is the user’s preference.
Lower installation heights will improve the efficiency of capturing cooking odours,
grease, and smoke. This rangehood must be installed between the minimum and
maximum dimensions indicated in the table above.
K

8
INSTALLATION INSTRUCTIONS
Venting options
Attention should be given to ensure that any applicable regulations concerning the
discharge of exhaust air are fulfilled.
The rangehood can be installed to operate with the exhaust air ducted externally from
the kitchen, or installed to operate with the exhaust air recirculating within the kitchen.
Ducted
For ducted installation it is recommended that 125 mm diameter, rigid or semi-rigid
ducting is used. This will require a 135 mm (min) round hole in the ceiling or wall.
Care should be taken to position the hole correctly.
For optimal efficiency use the shortest and straightest duct route possible and use rigid
or semi-rigid ducting for reduced noise and increased airflow. Flexible metal ducting
should only be used as a last resort (ie in difficult installations) and if used ensure that
it is straight and smooth and extended as much as possible.
Recirculating
To enable the product to operate
with the air recirculating, ensure
thelever on the motor casing
underthe filter is in the recirculation
position (see Fig.1) and close off the
duct hole with the cover provided
(see Fig.2). Purchase and install
carbon filters (refer to the ‘Parts
and accessories’ section).
The rangehood will channel the air
out of the vent on the front surface.
The carbon filters are required to
remove odours.
Note: a ducting hole is not
required in the wall or ceiling if the
rangehood is installed to operate
with exhaust air recirculating.
Fig.1
Fig.2

9
INSTALLATION INSTRUCTIONS
WARNING!
 This product is heavy and requires two persons for installation.
 Installation work and electrical wiring must be done by qualified person(s)
in accordance with all applicable codes and standards.
 Failure to install the screws or fixing device in accordance with these instructions may
result in electrical hazards.
IMPORTANT!
Wear gloves to protect against sharp edges.
The manufacturer is not liable for any damage caused by not following theseinstructions.
Installation
1Preparing for installation:
Before installing your rangehood:
 Please read the instructions carefully.
 Unpack the rangehood.
 Ensure that the voltage (V) and the frequency (Hz) indicated on the serial plate
match the voltage and frequency at the installation site.
 Check that all functions are working.
 Check that the area behind the installation surface to be drilled is clear of any
electrical cables or pipes, etc.
 The rangehood surfaces can be damaged during installation if grazed or knocked
by tools. Please take care to protect the surfaces during installation.
 Protect the cooktop surface with cardboard, or the like, to prevent damage occurring
whilst the rangehood is being installed above.
 Temporarily mark the height of the bottom of the rangehood and the centre of
thecooktop on the wall according to the information given in the ‘Installation
instructions – Height of rangehood’ section.
 The wall used for mounting the rangehood should have sufficient strength and a
flat surface.

10
TITLE TO GO HERE
Wall Mounting
1Attach the rangehood mounting screws to the wall
 Attach the upper rangehood mounting
screws in the locations shown in Fig.4.
Use 30 mm screws (and expansion plugs if
attaching to masonry). Ensure that there is
a 2 mm gap between the screw head and
the wall (see Fig.3).
INSTALLATION INSTRUCTIONS
PRODUCT DIMENSIONS mm
LRangehood attachment point width 540
MLower rangehood attachment point height 35
NUpper rangehood attachment point height 103
Fig.4
Upper rangehood
attachment points
Lower rangehood
attachment points
L
NM
Fig.3
2 mm

11
INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS
2Wall mounting
 Remove the filter – pull the relative catch and tilt the filter downwards until it
disengages from the supports (see Fig.5).
 Hang the rangehood off the upper rangehood mounting screws with 2 mm gap.
Hang off the keyhole attachment points on the back of the rangehood (see Fig.6)
then tighten the screws.
 Attach the lower rangehood mounting screws to fix the rangehood to the wall.
 Refit the filter.
3Remove packaging
 Remove all packaging and protective wrappings.
Fig.5
Fig.6

12
INSTALLATION INSTRUCTIONS
Under cupboard mounting
1Attach the ducting adapter to the rangehood (if ducted)
 Place the ducting adapter onto the hood and screw it in place using 10 mm screws
(see Fig.7).
2Mount the rangehood
 Remove the filter – pull the relative catch and tilt the filter downwards until it
disengages from the supports (refer to Fig.5 on page 10).
 Attach the rangehood to the cupboard using the mounting holes (refer to Fig.8 below).
 Create additional means of attachment using the extra holes found on top panel
ofthe rangehood. Ensure all fixings are secure.
 Refit the filter.
PRODUCT DIMENSIONS mm
ORangehood attachment point width 540
PRangehood rear attachment point 30
QRangehood front attachment point 301
Q
O
P
Fig.7
3Attach ducting (if ducted)
 Attach ducting to the ducting adapter using aluminium duct tape and vent outside.
4Remove packaging
 Remove all packaging and protective wrappings.
Fig.8

13
OPERATING INSTRUCTIONS
Control panel
Note: we recommend turning your rangehood on before you start cooking
for optimal performance.
Extractor fan
operating control
pilot light
Lighting
on and off
Extractor
fan off Extractor fan speed 1, 2 and 3

14
CLEANING AND MAINTENANCE
WARNING!
Unplug or disconnect the appliance from the power supply before servicing
or cleaning.
IMPORTANT!
 Never use abrasive or oil based cleaners.
 Wear gloves to protect against sharp edges.
Maintenance
The rangehood should be cleaned regularly using a mild, liquid detergent and a clean
soft cloth to avoid a build-up of grease occurring. Avoid the use of corrosive chemicals,
abrasive cleaning products, hard brushes and steel wool pads. Grease deposits are
corrosive which can cause damage to your rangehood.
Note: in areas of high humidity or coastal environments, cleaning should be carried out
more frequently.
Aluminium filters
 Depending on use, and at least once a month, the aluminium grease filter should be
removed and cleaned with hot soapy water or in a dishwasher.
 If washed in a dishwasher, the filter should be placed in an upright position to prevent
food from falling on it.
 After rinsing and drying, refit the filters.
Note: some discolouration of the frames may occur.
Removing the aluminium filters:
1Pull the relative catch, tilting the filter downwards until it disengages from thesupports.
2Reverse these instructions when refitting the filters.

15
CLEANING AND MAINTENANCE
WARNING!
When replacing the bulb, let the bulb cool, and assure that power to the light has been
turned off. Use new bulbs according to that indicated on the rangehood nameplate.
IMPORTANT!
 Use bulbs with an aluminium reflector to replace halogen bulbs. Do not use
dichroic bulbs – there is a risk of overheating.
 On rangehoods equipped with tungsten lamps, the lights should only be used
during operation of the motor. They should not be left on permanently and used
as a light source.
Carbon filters – for use in recirculation mode
Active carbon filters are disposable items designed to remove grease and odours from
cooking vapours before the air is channelled back into the kitchen. The active carbon
filters must be replaced periodically to work properly, at least every three months,
depending on the frequency with which the rangehood is used.
Note: fully saturated carbon filters can become a barrier to air movement therefore
limiting rangehood performance. In the event of fire, grease laden filters could
be flammable and therefore regular replacement is recommended.
Replacing the light bulb
Note: replacement bulbs are not covered by warranty.
1Remove aluminium grease filter.
2Replace light bulb with a light bulb no more powerful than that specified.
3Refit the aluminium filter.

16
PARTS AND ACCESSORIES
ITEM REFERENCE NUMBER
Light bulb 792507
Aluminium filter 792512
Recirculation carbon filter 792506
Ducting kit 125 mm (eaves) PD-RHK125E
Ducting kit 125mm (wall) PD-RHK125W

17
MANUFACTURER’S WARRANTY
You automatically receive a 2 year Manufacturer’s Warranty with the purchase of this
rangehood covering parts and labour for servicing within the country of purchase.
Fisher & Paykel undertakes to:
Repair or, at its option, replace without cost to the owner either for material or labour
any part of the product, the serial number of which appears on the product, which is
found to be defective within TWO YEARS of the date of purchase.
Note: this Manufacturer’s Warranty is an extra benefit and does not affect your
legal rights.
This Manufacturer’s Warranty DOES NOT cover
AService calls which are not related to any defect in the product. The cost of a service
call will be charged if the problem is not found to be a product fault. For example:
1Correcting the installation of the product.
2Instructing you how to use the product.
3Replacing house fuses or correcting house wiring or plumbing.
4Correcting fault(s) caused by the user.
5Noise or vibration that is considered normal, eg drain/fan sounds, refrigeration
noises oruserwarning beeps.
6Correcting damage caused by pests, eg rats, cockroaches, etc.
7Replacement light bulbs.
BDefects caused by factors other than:
1Normal domestic use; or
2Use in accordance with the product’s user guide.
CDefects to the product caused by accident, neglect, misuse or ‘act of God’.
DThe cost of repairs carried out by non-trained and supported service technicians or the
cost of correcting such repairs.
ENormal recommended maintenance as set out in the product’s user guide.
FRepairs when the appliance has been dismantled, repaired or serviced by other than a
Fisher&Paykel trained and supported service technician or the selling dealer.
GPick-up and delivery.
HTransportation or travelling costs involved in the repair when the product is installed
outside the Fisher&Paykel trained and supported service technician’s normal service area.
Nothing in this Manufacturer’s Warranty is intended to, or does, limit any rights you may
have under law to recover the costs of inspecting or returning the goods to us.
This product has been designed for use in a normal domestic (residential) environment.
This product is not designed for any commercial use (whatsoever). Any commercial use
by a customer will affect this product’s Manufacturer’s Warranty.
Service under this Manufacturer’s Warranty must be provided by a Fisher & Paykel
trained and supported service technician (refer to the ‘Customer Care’ section at the
back of this book). Such service shall be provided during normal business hours. This
Manufacturer’s Warranty certificate should be shown when making any claim.

18
MANUFACTURER’S WARRANTY
For Australian Customers
This Manufacturer’s Warranty is an extra benefit and does not affect your legal rights.
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and
compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
Please keep this user guide in a safe place.