Fisher-Price LO540 User manual

Newborn Baby
Older Baby
Toddler
www.fisher-price.com/uk
L0540
WARNING
IMPORTANT! KEEP INSTRUCTIONS
FOR FUTURE REFERENCE.

2
To prevent serious injury or death:
• Fall Hazard - It is dangerous to use this
product on an elevated surface, since
child’s movement may cause the product
to slide or tip over. Use only on a floor.
• Suffocation Hazard - Never use on a soft
surface (bed, sofa, cushion) since the
product can tip over and cause suffoca-
tion in soft surfaces.
• Never leave child unattended.
• Never use as a carrier or lift while
child is seated. Never use the toy bar
as a handle.
• Use the upright position only when
child has developed enough upper body
control to sit without leaning forward.
• Always use the restraint system until
child is able to climb in and out of the
product unassisted.
• Reclined position not recommended
for children who cannot sit up by them-
selves (6 months approximately,
until 9 Kg/20 lbs).
WARNING
2
Consumer Information
CAUTION
This package contains small parts in
its unassembled state. Adult assembly
is required.
• Please read these instructions before assembly and use of this product.
• Adult assembly is required.Tool needed for assembly: Phillips screw-
driver (not included).
• Requires one “D” (LR20) alkaline battery (not included) for soother
operation.Toy includes one non-replaceable button cell battery.
• Product features and decorations may vary from photographs.
Parts
IMPORTANT! Please remove all parts from the package and
identify them before assembly.
Pad with Seat Back Tube
Hint: Please refer to the care
section to remove the seat back
tube for cleaning.
Toy (Toy may
be different)
Toy Bar
Front Bar
2 Side Rails Crossbar
Note: Tighten or loosen the screws with a Phillips screwdriver.
Do not over-tighten the screws.
Shown Actual Size
#4 x 20 mm Screws – 6

3
2
• First lift the front rails and then push out the back rails.
Assembly
• Place the side rails on a flat surface.
• Fit the crossbar tabs into the small rectangular opening in each side
rail. Push the crossbar down completely.
• Insert two #4 x 20 mm screws into the crossbar and tighten.
• Insert and "snap" the back rails into the sockets in the side rails.
Pull up on the back rails to be sure they are secure.
IMPORTANT! Before assembly and each use, inspect this product
for damaged hardware, loose joints, missing parts or sharp edges.
DO NOT use if any parts are missing or broken. Contact Mattel
for replacement parts and instructions if needed. Never
substitute parts.
1
Side Rails
Crossbar
LIFT
3
PUSH
LIFT
PUSH
4
Side Rails
Front Bar
Hint: You may want to install batteries into the soother before
assembling the front bar to the front rails.
• Position the front bar so that the soother is upright. Fit it to grooved
area on the inside of the front rails.
• Insert four #4 x 20 mm screws into the front rails and tighten.
Hint: You may need the help of another adult to hold the front
bar in place while you insert and fasten the screws.

4
Assembly
• Insert the ends of the seat back tube (inside the pad) into the
sockets in the front rail. Push down on the seat back tube until
you hear a “click” on each side.
• Pull up on the seat back tube to be sure it is secure.
5
Pad
Seat Back Tube
Socket
Socket
• Locate the pocket in the bottom of the pad.
• Fit the hardboard (attached to the front bar) into the pocket in
the pad.
6
Pocket
Hardboard
• Fit the clips on the front edge of the pad to the bottom edge of the
front bar.
7
Clips
• Wrap a pad flap around a front rail and fasten the buckle. Make sure
you hear a “click”.
• Repeat this procedure to fasten the other pad flap.
8
Pad Flap
Buckle

5
Assembly
9
• Fit the toy bar clamp to the top of the front rail. Push the toy bar
clamp down to “snap” it into place.
Hint: To remove the toy bar, lift the edge of the clamp and pull
to remove.
Toy Bar
Clamp
• Fit the toy into the slot in the top of the front rail.
10
Slot
Toy

6
• Turn the product face down.
• Loosen the screw in the battery compartment door and remove the
battery compartment door.
• Insert one “D” (LR20) alkaline battery into the battery compartment.
• Replace the battery compartment door and tighten the screw.
IMPORTANT! If vibrations become faint, or if there are no
vibrations, remove the “D” (LR20) battery from the soothing unit and
dispose of it properly. Replace the battery with a new “D” (LR20)
alkaline battery.
Battery Installation
• Protect the environment by not disposing of this product with
household waste (2002/96/EC). Check your local authority for
recycling advice and facilities (Europe only).
+"D" (LR20)
1,5V x 1
Hint: We recommend using an alkaline battery for longer
battery life.
Battery Safety Information
In exceptional circumstances, batteries may leak fluids that can cause
a chemical burn injury or ruin your product.To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types:
alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use.Always remove
exhausted batteries from the product. Dispose of batteries safely.
Do not dispose of this product in a fire.The batteries inside may
explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be
charged under adult supervision.
-

7
Newborn-to-Toddler Portable Rocker
Toddler
Newborn Baby
Older Baby

8
Setup
To prevent serious injury or death:
• Use the upright position only when child
has developed enough upper body control
to sit without leaning forward.
• Reclined position not recommended for
children who cannot sit up by themselves
(6 months approximately, until 9 Kg/20 lbs).
WARNING
UPRIGHT
Upright
Fasten the straps on the back of the seat. Make sure you hear a “click”.
Recline
Unfasten the straps on the back of the seat.
To prevent serious injury or death:
• Fall Hazard - It is dangerous to use this
product on an elevated surface, since
child’s movement may cause the product
to slide or tip over. Use only on a floor.
• Suffocation Hazard - Never use on a soft
surface (bed, sofa, cushion) since the
product can tip over and cause suffoca-
tion in soft surfaces.
WARNING
Seat
Rotate the kickstands out to convert to a seat.
Kickstand
SEAT
Kickstand
Rocker
Rotate the kickstands in to convert to a rocker.
ROCKER
RECLINE

9
Setup
LIFT
Extend Frame
While pressing the buttons on the back of the frame, lift the seat
back to extend the frame for toddler use.
Shorten Frame
While pressing the buttons on the back of the frame, push the seat
back to shorten the frame for newborn or older baby use.
To prevent serious injury or death: Never
use the toy bar as a handle.
WARNING
Toy Bar
Clamp
Toy Bar
• Fit the toy bar clamp to the top of the front rail. Push the toy bar
clamp down to “snap” it into place.
Hint: To remove the toy bar, lift the edge of the clamp and pull
to remove.
PRESS
PRESS
PUSH
PRESS
PRESS
SHORTEN FRAME
EXTEND FRAME

10
To prevent serious injury or death:
• Never leave child unattended.
• Never use as a carrier or lift while child
is seated.
• Always use the restraint system until
child is able to climb in and out of the
product unassisted.
WARNING
Secure Your Child
• Turn the toy bar out of the way or remove it altogether.
• Place your child in the seat. Position the restraint pad between your
child’s legs.
• Fasten the waist belts to each side of the restraint pad. Make sure
you hear a “click” on both sides.
• Check to be sure the restraint system is securely attached by pulling
it away from your child.The restraint system should remain attached.
1
Waist Strap Waist Strap
Restraint Pad
2TIGHTEN
Anchored End
Free End
To tighten:
• Feed the anchored end of the waist strap up through the buckle to
form a loop  . Pull the free end of the waist strap  .
To loosen:
• Feed the free end of the waist strap up through the buckle to form
a loop  . Enlarge the loop by pulling on the end of the loop toward
the buckle. Pull the anchored end of the waist strap to shorten the
free end of the waist strap  .
Anchored End
Free End
LOOSEN