Fisher-Price V4826 Assembly instructions

V4826
www.fisher-price.co.uk
IMPORTANT! KEEP FOR FUTURE REFERENCE.

2
Consumer Information
This product contains small parts in its
unassembled state. Adult assembly is required.
CAUTION
To prevent injury or death from falls and
being strangled in the restraint system:
• Always use the restraint system.
• Not recommended for children who can sit
up by themselves (6 months approximately,
until 9 Kg/20lbs).
• Never leave child unattended.
• It is dangerous to use this product on an
elevated surface.
• Never use toy bar as a handle.
WARNING
• Please read these instructions before assembly and use of
this product.
• Adult assembly is required.
• Tools required for assembly: Allen wrench (included) and Phillips
screwdriver (not included).
• Requires four “C” (LR14) alkaline batteries for swing/sounds
operation and one “D” (LR20) alkaline battery for vibration unit
operation. Batteries not included.
IMPORTANT! The weight limit for this product is 9 kg (20 lb).
If your child weighs less than 9 kg (20 lb), but is really active
and appears to be able to climb out of the swing, immediately
discontinue its use.
• Product features and decoration may vary from the photographs.
Assembled Parts
IMPORTANT! Please remove all parts from the package and identify
them before assembly. Some parts may be packed in the pad.
Both Shown Actual Size
Note: Tighten all assembled screws with the
enclosed Allen wrench.
2 Swing Housings
Seat Back
2 Side Rails
Seat Pad Base
Frame
M6 x 25 mm Screw – 2 #8 x 2,5 cm (1”) Screw – 7
Seat Bottom Toy Bar
Allen Wrench
Hinge Rod

3
Assembly
2
• Position one of the swing housings so that the swing arm is
facing the inside of the assembly.
• Fit the swing housing onto the frame tube.
Hint: The swing housing is designed to fit one way. If it does not
seem to fit, try assembling it to the other frame tube.
Swing Arm
Frame Tube
1
• Insert and “snap” the base into the sockets in each side of the
frame, as shown.
Hint: The base is designed to fit one way. If it does not seem to fit,
turn it around and try again.
Base
Frame
IMPORTANT! Before assembly and each use, inspect this product
for damaged hardware, loose joints, missing parts or sharp
edges. DO NOT use if any parts are missing or broken. Contact
Fisher-Price®for replacement parts and instructions if needed.
Never substitute parts.
4
• Insert an M6 x 25 mm screw into the hole in the swing housing.
Fully tighten the screw with the Allen wrench.
• Repeat this procedure to assemble the remaining swing housing
to the other frame tube.
• Fit the tabs on the seat bottom into the slots in the seat back.
3
Seat Back
Tabs
Seat Bottom

4
Assembly
• Make sure the tab on each side of the seat back is fitted inside the
socket on each side of the seat bottom.
• Insert the hinge rod through the hinge on the seat assembly.
• Insert a #8 x 2,5 cm (1”) screw into the end of the hinge rod.
Tighten the screw with the Allen wrench.
Side View
Side View
5
Tab Tab
Hinge Rod
• Fit the side rails under the grooved areas under the seat, as shown.
• Insert four #8 x 2,5 cm (1”) screws into the holes in the seat.
• Tighten the screws with the Allen wrench.
7
• Fit the end of each swing arm into the grooves in the seat.
Swing ArmGroove
Side View
Side View
6
Side Rails
• Insert a #8 x 2,5 cm (1”) screw into each swing arm. Tighten the
screws with the Allen wrench.
IMPORTANT! Push down on the seat assembly to be sure it’s secure
to the swing arms.
Swing Arms
Side View
Side View
8

5
Assembly
9
10
• Insert the shoulder and waist restraint belts through the slots in
the seat pad.
Hint: The shoulder belts come assembled to the seat back in the
lower slots for a smaller child. To change to the upper slots for
a larger child, refer to page 16.
• Insert the crotch restraint belt up through the slot in the seat pad.
Crotch Restraint
Crotch Restraint
Waist Restraints
Waist Restraints
Shoulder Restraints
Shoulder Restraints
11
• Fit the pocket on the back of the seat pad onto the seat back.
Side View
Side View
Pocket
Pocket

6
Assembly
15
14
• Insert the end of the toy bar into the socket in the swing housing.
Hint: The toy bar only fits one way. If it does not seam to fit, turn it
around and try again.
• Fit the notch in the seat pad around each swing arm.
• Hook the seat pad elastic loops to the tabs on the seat.
Toy Bar
Toy Bar
Swing Arm
Elastic Loops
Elastic Loops
ng
Arm
ng
Arm
13
• Fit the clips on the front edge of the seat pad to the front edge of
the seat bottom.
Clips
Clips
Elastic Loops
Elastic Loops
Elastic Loops
Elastic Loops
Tab
Tab
Tab
Tab
Bottom View
Bottom View
12
• Lift the front edge of the seat pad and insert both elastic loops on
the seat pad through the holes in the seat bottom.
• From the bottom of the seat, hook the elastic loops to the tabs on
the seat.

7
Battery Installation
Hint: We recommend using alkaline batteries for longer battery life.
Swing/Sounds Battery Installation
• Locate the swing/sounds battery compartment on a swing housing.
• Loosen the screws in the battery compartment door with
a Phillips screwdriver. Remove the battery compartment door.
• Insert four “C” (LR14) alkaline batteries into the battery compartment.
• Replace the battery compartment door and tighten the screws
with a Phillips screwdriver.
1,5V x 4
“C” (LR14)
Vibration Battery Installation
• Locate the vibration battery compartment on a swing housing.
• Loosen the screw in the battery compartment door with a Phillips
screwdriver. Remove the battery compartment door.
• Insert one “D” (LR20) alkaline battery into the battery compartment.
• Replace the battery compartment door and tighten the screw with
a Phillips screwdriver.
1,5V x 1
“D” (LR20)
• If this product begins to operate erratically, you may need to reset
the electronics. Turn the power off and then back on.
• When motion or sounds from the product become slow/faint or
stop, replace the batteries.
• Protect the environment by not disposing of this product
with household waste (2002/96/EC). Check your local
authority for recycling advice and facilities (Europe only).
Battery Safety Information
In exceptional circumstances, batteries may leak fluids that
can cause a chemical burn injury or ruin your product. To avoid
battery leakage:
• Do not mix old and new batteries or batteries of different types:
alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove
exhausted batteries from the product. Dispose of batteries safely.
Do not dispose of this product in a fire. The batteries inside may
explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be
charged under adult supervision.

8
Securing Your Child
Restraint System
• Place your child in the seat.
• Insert the ends of the waist belts through the slots in the
shoulder belts.
• Pull the crotch belt up between your child’s legs and fasten both
waist/shoulder belts to the crotch belt. Make sure you hear
a “click” on both sides.
1
Waist/Shoulder Belts
Waist/Shoulder Belts
Crotch Belt
Crotch Belt
• Tighten each waist belt and shoulder belt so that the restraint
system is snug against your child. Please refer to the next section
for instructions to tighten these belts.
2
To prevent injury or death from falls and
being strangled in the restraint system:
• Always use the restraint system.
• Not recommended for children who can sit
up by themselves (6 months approximately,
until 9 Kg/20lbs).
• Never leave child unattended.
• It is dangerous to use this product on an
elevated surface.
• Never use toy bar as a handle.
WARNING
• To tighten the waist belts: Feed the anchored end of the waist
belt up through the buckle to form a loop A. Pull the free end of
the waist belt B.
• To tighten the shoulder belts: Hold the adjuster and pull the
shoulder belt down C.
• To loosen the waist belts: Feed the free end of the waist belt up
through the buckle to form a loop A. Enlarge the loop by pulling
on the end of the loop toward the buckle.
• Pull the anchored end of the waist belt to shorten the free end of
the waist belt B.
• To loosen the shoulder belts: Pull the adjuster down C.
Note: After adjusting the restraint system to fit your child, make sure
you pull on it to be sure it is securely fastened.
3TIGHTEN LOOSEN
Adjuster
Adjuster
Adjuster
Adjuster

9
To adjust the restraint height for baby, unbuckle the restraint system.•
4
Securing Your Child
Larger Baby
• Insert the ends of the shoulder belts through the upper slots in
the pad.
6
Upper Slots for
Upper Slots for
Larger Baby
Larger Baby
Push to remove the shoulder belts from the seat back.•
5
Shoulder Belts
Shoulder Belts
Smaller Baby
• Insert the ends of the shoulder belts through the lower slots in
the pad.
7
Lower Slots for
Lower Slots for
Smaller Baby
Smaller Baby

10
Easy Conversion
• Pull and slide the seat latch off of the seat post.
Seat Post
Seat Post
Seat Latch
Seat Latch
Swing Mode
• Lower the seat post on the seat bottom.
• While holding the seat post, lift the seat latch. Slide the seat latch
over the seat post.
Seat Post
Seat Post
Seat Latch
Seat Latch
Seat Mode
Seat Mode