Fisher-Price J7814 User manual

www.fisher-price.co.uk
J7814
1
Infant
2
Older Baby
3
Note: Use the hammock (con-
nected to all four corners of the
bathtub) only for a baby that weighs
up to 4,54 kg (10 lbs).
Newborn
IMPORTANT! KEEP INSTRUCTIONS FOR
FUTURE REFERENCE.
WARNING
3-6 months and up to 9 kg
6 months + and up to 11 kg

WARNING
2
Consumer Information
Consumer Information
Parts
Parts
3 Toys
Bathtub
Hammock
Bases
#8 x 2,5 cm (1”) Screw – 2
Fastener Shown Actual Size
• Please read these instructions before assembly and use of
this product.
• Adult assembly is required. Tool needed for assembly:
Phillips Screwdriver (not included).
• Water toys sometimes get messy. Protect play surfaces
before use.
• Overfilling the bathtub may cause it to leak.
• After each use, drain and rinse all items.
• Before storing, drain, clean, rinse and dry all items.
• The hammock is surface wash only with a mild cleaning
solution and damp cloth. Do not use bleach. Rinse the
hammock thoroughly.
Squeeze excess water from the
hammock and line dry.
• Product features and decoration may vary from photos.
CAUTION
This product contains small parts
in its unassembled state. Adult
assembly is required.
Warning and Caution
Warning and Caution
DROWNING HAZARD
• Babies have DROWNED in infant bathtubs.
• Babies can drown in as little as 2.5 cm (1")
of water.
• ALWAYS bathe your baby in as little water
as possible.
• NEVER place this product in water in an
adult bath tub or sink. ALWAYS keep the
drain open in the adult bath tub or sink.
ALWAYS keep the drain open in the adult
bath tub or sink.
• ALWAYS keep baby within adult's reach.
• NEVER allow other children to substitute
for adult supervision.
• NEVER lift this product with baby in it.
• ALWAYS test water temperature for
comfort on wrist before placing baby in
this product.
• ALWAYS test this product for secure fit
in domestic sink or bath. For domestic
use only.

3
Set-up the Aquarium Bath Centre for use with a 1Newborn,
2Infant or 3Older Baby.
One - Time Assembly
One - Time Assembly
3 Stages of Use
3 Stages of Use
IMPORTANT! Before assembly and each use, inspect this product for
damaged hardware, loose joints, missing parts or sharp edges.
DO NOT
use if any parts are missing or broken. Contact Mattel for
replacement
parts and instructions if needed. Never substitute parts.
• Turn the bathtub upside down on a flat surface.
• Match the number on each base to the number near each socket
on the bathtub.
• Insert a screw into each base and tighten with a Phillips screw-
driver. Do not over-tighten.
Bathtub
Base
1
3
2

4
Newborn
Newborn
• Fit the clips on the headrest end of the hammock to the narrow
end of the bathtub. Fit the clips on the other end of the hammock
to the wide end of the bathtub.
• Tighten the hammock fit as much as possible. Pull the free end of
the belts.
• Fit the bathtub to the sink, or place on a flat surface.
• Fit the plug into the hole in the bottom of the bathtub.
• Fill the bathtub with as little water as possible to bathe baby.
ALWAYS test water temperature in the product before placing
baby in the product. Typical water temperature should be between
32° and 38° C.
• Plug the toy into the side slot in the bathtub.
• Carefully place baby on the hammock.
Hint: To loosen hammock fit, lift the buckle.
Clips
Clips Headrest
Wide End
Narrow End
1
TIGHTEN LOOSEN

Clips
Headrest
Narrow End
• Fit the clips on the headrest end of the hammock to the narrow end
of the bathtub.
• Lay the bottom of the hammock in the bathtub.
• Fit the bathtub to the sink, or place on a flat surface.
• Fit the plug into the hole in the bottom of the bathtub.
•
Fill the bathtub with as little water as possible to bathe baby.
ALWAYS test water temperature in the product before placing
baby in the product. Typical water temperature should be between
32° and 38° C.
• Plug the toy into the side slot in the bathtub.
• Carefully place baby on the hammock.
Infant
Infant
2
• Place the bathtub in a larger bathtub, or place on a flat surface.
• Fit the plug into the hole in the bottom of the bathtub.
• Fill the bathtub with as little water as possible to bathe baby.
ALWAYS test water temperature in the product before placing
baby in the product. Typical water temperature should be between
32° and 38° C.
• Plug the toy into the side slot in the bathtub.
• Carefully place baby in the bathtub.
5
Older Baby
Older Baby
3

www.service.mattel.co.uk
Telephone [phone]
Great Britain: Mattel UK Ltd., Vanwall Business Park, Maidenhead SL6 4UB.
Australia: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond, Victoria 3121 Australia.
Consumer Advisory Service 1300 135 312.
New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.
Asia: Mattel East Asia Ltd, Room 1106, South Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China.
Questions?
If you are missing parts or need assistance, we can help!
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A. PRINTED IN CHINA
©2008 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. J7814b-0726