Flamerite Fires Glazer 600 User manual

1 | Page
Installation, Precautions & Servicing
Glazer
600 900 1000 1500 1800
Luca
450 1500
IMPORTANT
This product is only suitable for well insulated spaces or occasional use
Carefully remove the fire from the packing checking neither the heater nor the power
cable has been damaged during transport. Do not operate the fire if damaged. Please
bear in mind the weight of the fire before removal from the packaging and installation.
Consider if help is required. Always read this manual first before attempting to install
or use and keep in a safe place. Any alteration to the power cable should only be done
by a qualified electrician.
Your fire is guaranteed for two years from the date of purchase. In the unlikely event
of a breakdown you have access to our customer services team, simply call 01543
251122 during office hours, 9am – 5pm or e-mail on [e-mail] The
accessories are found in a box that is packed at the side of the fire.

2 | Page
•WARNING: In order to avoid overheating, do not cover the heater.
•For indoor use only.
•Do not use the fire in the vicinity of a bath, shower or swimming pool.
•Never use the fire to dry laundry.
•The heater must not be located immediately below a socket outlet.
•The use of an extension lead is not recommended.
•This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been given
supervision or instruction concerning use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made
by children without supervision.
•Children of less than 3 years should be kept away unless continuously supervised
•Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it
has been placed or installed in its intended normal operating position and they have been given
supervision or instruction concerning use of the appliance in a safe way and understand the hazards
involved.
•Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or
perform user maintenance.
•Some parts of this product can become very hot and cause burns. Particular attention must be given
where children and vulnerable people are present
•Caution should be applied to ensure that children do not play with the fuel effects.
•As with any electrical appliance whilst the instructions aim to cover as many eventualities as possible,
caution and common sense should be applied when operating your appliance, particularly in the
vicinity of small children.
•CAUTION: The heater is fitted with an automatic cut out to prevent any damage due to overheating.
The element will continually and automatically cut out if the airflow is obstructed. Never cover the air
outlets. To reset, switch the fire off, disconnect from the mains supply, remove the cause of the
overheating. Allow to cool for a suitable period then switch the fire back on.
•CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut out, the
appliance must not be supplied through an external switching device, such as a timer, or connected to
a circuit regularly switched on and off by a utility.
Important Safety Information and Warnings
Where a chimney is not blocked off completely, any draw will cause the heater to cut
out during use. Care should also be taken when fitting into a cavity wall in case of
damp or draft with external air vents fully sealed

3 | Page
Electrical connections. Your appliance comes fitted with a plug that incorporates a 13A fuse. The replacement
fuses must be 13A and ASTA approved. If the fuse cover is lost the plug must not be used until a replacement
cover, of the same colour, is obtained from an electrical retailer. The appliance is fitted with a moulded plug if
it is necessary cut off the plug, for any reason, it must be discarded immediately with the fuse removed.
Under no circumstances should any attempt be made to reuse the plug, do not insert into any 13A socket as
this could cause a hazard. If the mains cable is damaged it must be replaced by the manufacturer or an
authorised technical service centre.
WARNING THIS APPLIANCE MUST BE EARTHED
IMPORTANT
The wires in the mains lead are coloured in accordance with the following code.
Green and yellow:
EARTH
Blue:
NEUTRAL
Red:
LIVE
As the colours of the wires in the mains lead of this appliance may not correspond with the colour markings in
your plug proceed as follows: -
•The wire which is coloured green and yellow must be connected to the terminal in the plug
which is marked with the letter E, or coloured green or coloured green and yellow, or marked
with the earth symbol
•The wire which is coloured blue must be connected to the terminal in the plug which is marked
with the letter N, or coloured black.
•The wire which is coloured brown must be connected to the terminal in the plug which is marked
with the letter L, or coloured red.
RECYCLING
Please recycle responsibly. Take your item to your local recycling
centre. You can easily locate your nearest centre on
the www.recyclenow.com website or check with your retailer for
details on either a collection service or a store take-back scheme (some
may apply charges). Councils may offer a household recycling
collection service for small electrical items; contact your local authority
for more details.
Electrical Connections
Insert the plug tightly into its IEC connector underneath the fire if not already done
so. If the removal of the plug is absolutely necessary for installation, cut off in an
area within 100mm only of the plug itself. Any further will affect your warranty.

4 | Page
DO NOT TWIST, FORCE OR SQUEEZE THE FIRE DURING THE INSTALLATION PROCESS.
There must be enough clearance for the fire to comfortably fit inside or against a wall. DO NOT SQUEEZE INTO
AN OPENING as this may deform the case and stop the glass from moving correctly.
The height at which you may wish to fix the fire in or on the wall is up to you, we recommend anywhere from
350-450mm from the floor to the bottom of the fire opening (not the bottom of the fire).
The fire must be well supported in or on any structure. A wall support or lintel should be fitted at the required
height to ensure the appliance does not support the weight of the finished wall or chimney breast. Never
secure to just plater board alone.
Minimum opening to fit and inset the fire
Model H W1side W2side W3side D
600 725mm 645mm 625mm 610mm 265mm
900 505mm 945mm 925mm 910mm 265mm
1000 575mm 1045mm 1025mm 1010mm 265mm
1500 575mm 1545mm 1525mm 1510mm 265mm
1800
575mm 1845mm 1825mm 1810mm 265mm
Visible burn area after fitting
Model H W1side W2side W3side D2/3 side
600 500mm 645mm 625mm 600mm 180mm
900 280mm 945mm 925mm 900mm 180mm
1000 350mm 1045mm 1025mm 1000mm 180mm
1500 350mm 1545mm 1525mm 1500mm 180mm
1800
350mm
1845mm
1825mm
1800mm
180mm
1 side 2 side 3 side
Installation Instructions

5 | Page
1. Luca 450 freestanding (with or with out log box)
Move and position to your required location and go to Fuel Effectsin the next section. If fitting the optional
flue pipe, this is simply placed onto top and against the wall.
2. Glazer Side panels for 1 or 2-sided fitting
If you have purchased the Glazer fire only and not part of a Flamerite Fireplace Suite, it will come with the
blanking panels attached. These allow the Glazer to convert from a 1 sided, into a 2 or 3-sided fire. The
blanking panels consist of two parts each and are fitted directly over the side glass. If one or both are not
required, remove the 4 screws and remove the panel(s). If you need to fit the blanking panel(s) following the
instructions and images below.
•Place together as though you have formed a tray with an edge/return on each of the four sides
•Slide onto the fire so the forward edge/return of the inner panel touches the glass panel edge.
•Fix using the four screws, two on the top and bottom but make sure the inner panel and the glass have
free movement to slide forwards and backwards.
3. Glazer & Luca fitting onto a wall or into a structure
(Luca 450, go to section 5 for intruction on how to remove and reattach top and base before
commencing this instrction).
Take the following steps securing your fire firmly into position and onto a wall. Both top and bottom fixing
brackets come already attached to the fire. The bottom bracket will have to be removed to begin the process.
a. Bottom Bracket
Fixings
450
600
900
1000
1500
1800
60mm screws
2
3
4
4
4
4
M10 rawl plugs
2
3
4
4
4
4
M6 bolts
2
2
2
2
2
2
M6 washers
2
2
2
2
2
2

6 | Page
Remove the M6 bolts and washers (remove the bottom bracket only). Mark up and drill the holes with an
M10 bit and fit the rawl plugs. Using the 60mm screws, secure the bracket to the wall.
b. Top Bracket
Fixings
450
600
900
1000
1500
1800
60mm screws
2
3
3
3
3
4
M10 rawl plugs
2
3
3
3
3
4
13mm screws
2
3
4
4
4
4
A second person maybe required. For now, leave the top bracket attached.
Place and hold the fire on the bottom bracket and refit the M6 bolts and washers through the slots back into
the fire. Keeping the fire firmly pushed against the wall, mark across the length of the top bracket and into
the slots above each hole. Once again remove the M6 bolt and washers and place the fire onto the floor.
Remove the 13mm screws and top bracket from the fire. Using it as a template mark the fixing holes on the
wall, drill the holes with an M10 bit and fit the rawl plugs. Using the 60mm screws fix the bracket to the wall.
c. Secure the fire onto the brackets

7 | Page
Place and hold the fire on the bottom bracket and screw the top bracket back onto the fire with the 13mm
self-tappers. At this point you will be able to level the fire accordingly when refitting the M6 bolts and washers
through the slots of the bottom bracket and back into the fire.
Your fire is now secure, make sure the mains cable is tightly fitted.
4. Glazer fitting a Flamerite fireplace suite
Modular wall
8x 13mm screws. 4 top and 4 bottom
& freestanding
Modular chimney
3x M10 x 50mm Rawl plugs. 3x 60mm screws
breast
2x 50mm screws & cover caps. 4x 13m screws.
a. When the fire is mounted to the wall, the base will slide on from the front between the flange running
around the opening and the pull-out tabs A. Make sure the power cable is firmly pushed into the fire
and does not foul the suite when up against the wall.
b.

8 | Page
c. Using four of the 13mm screws secure the base to the fire along the side flange and fit the décor trim
B. The décor trim is the long black channel that provides a neat edge along the bottom of the fire
opening, it is held in place with magnets.
d. Fix the gloss black decorative panels either side of the opening to the fire C, also held in place with
magnets.
e. If fitting a full chimney breast go to next step e.

9 | Page
Slide the top from the front Dbetween the flange running around the opening and the pull-out tabs.
Make sure the top of each gloss black decorative panel C fits into the recess around the cut out as the
top pushes back towards the wall. On the underside using four of the 13mm self-tappers provided,
secure the sides of the top only.
f. The chimney breast requires a baton to be fitted to the wall above the fire using three M10 x 50mm
rawl plugs and 60mm screws. Use an M10 bit to drill the holes. The baton must be fitted from the top
of the fire to the bottom of the baton, dead centre so the chimney breast can comfortably slide over
the fire and line up to the pilot holes either side of the baton.
Height from the top of the fire: 600 = 885mm/900 = 1110mm/1000 = 1040mm
Carefully slide the chimney breast on from the front Dbetween the flange running around the opening
and the pull-out tabs. Make sure the top of each gloss black decorative panel C fit into the recess
around the cut out as the chimney breast pushes back towards the wall. Use the two 50mm screws to
secure the chimney breast to the baton Fand push the white plastic covers over the top. On the
underside use four 13mm screws provided, secure the sides only.
DO NOT HANG HEAVY OBJECTS ONTO THE CHIMNEY BREAST

10 | Page
5. Luca top and base, remove and replace.
(Illustrations in this instance show the 450, the sme priceipal should be applied to the 1500)
•Remove the four screws and slide the top forward.
•Remove the two side and front dresser rails, they are held on with magnets.
•Remove the four screws and slide the top forward.
Go to back to section 2: Fitting onto a wall or into a structure

11 | Page
The fuel effects must be positioned as in the images below.
Care must be taken to ensure the channel at the front of the fire is not obstructed. Anything dropped into
it, must be removed before installing the front glass panel.
Visit www.flameritefires.com/product-support/instructions-fuel-effects.html if you require clearer
downloadable images.
Radia Flame Log Bed
For the best possible log burn, place only a thin amount of the grey chippings around the perimeter on
the fuel bed.
Nitra Flame Log Bed
Using the three bags of clear glass chippings, lightly fill the insde of the fuel bed, leaving clear only a small area
around the perimeter
For the best possible log burn, place only a thin amount of the grey and black chippings around the
perimeter on the fuel bed.
Fuel Effects

12 | Page
450

13 | Page
600
900 & 1000

14 | Page
1500 & 1800
The red line in the first image, is the centre of the fire. Leave approximately 150mm either end of logs 15 & 18
to allow the 1800 logs 19 to 25 to be fitted at either end.

15 | Page

16 | Page
We recommend two persons to fit the Glazer 1500 & 1800 glass
Push the side glass back towards the rear of the case A
You will notice there is a long gap on the underside of the opening 10mm in width that runs along and in front
of the heater grills. At an angle of approximately 45 degrees push the glass up into this void making sure the
bottom of the glass clears the lower edge of the opening. Tilt the glass back into the fire and carefully lower
into the large channel that runs across the opening avoiding the dampers B & C
Slide the handle Dalong the top right-hand side of the glass.
The upper glass rail is magnetic and will fix easily into place along the top of the opening E. Adjust the
position of the handle accordingly into the gap on the rail.
With the front glass tilted rearwards pull the side glass side forwards F. To open and close the front glass
panel, place your index finger on the handle as shown in the picture G. You may finely position the front and
side glass panels to give the best possible fit and finish. Make sure the front glass glides back with ease and
depresses the micro switch arm on the underside of the heat housing.
Glass Fitting & Removal

17 | Page
WARNING: Before any maintenance/cleaning is undertaken, always disconnect the fire from the mains
power supply.
Replacing Radia Flame LED Lamps
Dimmable 240V 6W 3000k E14 LED lamps
We recommend lamp replacement by a Flamerite service engineer or similarly qualified persons in order to
avoid a hazard. Allow a suitable time for the lamps to cool then remove the glass & fuel effect (see
Installation). Remove the two screws from either side of the fuel bed and lift out of place. Remove and
replace the lamps, fuel bed, fuel effect and glass. Please note that replacement lamps are covered by a 2-year
warranty. Replacements are available from Flamerite Fires Ltd
Replacing Nitra Flame LED Strips
LED Strips and driver replacement must be undertaken by a Flamerite service engineer or similarly qualified
persons in order to avoid a hazard. Please note that replacement lighting is covered by a 2-year warranty.
Replacements are available from Flamerite Fires Ltd
Cleaning
The fire can be cleaned with a soft cloth and non-abrasive glass cleaner.
•No power to the fire: Check the wall socket, plug, fuse and dimmer.
•Heat turns off quickly after turn on: Set thermostat to a higher temperature.
•No illumination: Make sure fire is turned on. Check heater is working, if so check dimmer.
•Heater blowing cold air:The safety cut out may have operated. Check for obstruction around the
heater. If continually a problem and fitted into a cavity wall or chimney breast check with installer the
inset opening has been 100% fully sealed from drawn air and draft.
•Noise when illuminated: Due to moving parts, the electric fire will make a noise.
•Noise from the heater when in use: The sound of rushing air is normal.
Maintenance
Trouble Shooting

18 | Page
Information requirement for electric local space heaters
Radia Flame
Model identifier (s)
450
600
900
1000
1500
1800
Item@ 240v 50Hz
Symbol
Value
Value
Value
Value
Value
Value
Unit
Heat
output
Nominal heat output
Pnom
1.5
1.5
1.5
1.5
1.5
1.5
kW
Minimum heat output
(indicative)
Pmin 0.75 0.75 0.75 0.75 0.75 0.75 kW
Maximum continuous heat
output
Pmax,c 1.5 1.5 1.5 1.5 1.5 1.5 kW
Auxiliary electricity consumption
At nominal heat
elmax
0.038
0.033
0.051
0.051
0.063
0.082
kW
At minimum heat
elmin
0.038
0.033
0.051
0.051
0.063
0.082
kW
In stand by
elSB
0.0005
0.0005
0.0005
0.0005
0.0005
0.005
kW
Type of heat output/room temperature
control
With distance control option
Room temperature control, with open window detection
Yes
Adaptive Start
Yes
With electronic room temperature control plus week timer
Yes
Contact details:
Flamerite Fires Ltd. Greenhough Road, Lichfield. Staffs. WS13 7AU
Nitra Flame
Model identifier (s) 450 600 900 1000 1500 1800
Item
@ 240v 50Hz
Symbol
Value
Value
Value
Value
Value
Value
Unit
Heat
output
Nominal heat output
Pnom
1.5
1.5
1.5
1.5
1.5
1.5
kW
Minimum heat output (indicative)
Pmin
0.75
0.75
0.75
0.75
0.75
0.75
kW
Maximum continuous heat
output
Pmax,c 1.5 1.5 1.5 1.5 1.5 1.5 kW
Auxiliary electricity consumption
At nominal heat elmax 0.03 0.027 0.041 0.041 0.051 0.058 kW
At minimum heat
elmin
0.03
0.027
0.041
0.041
0.051
0.058
kW
In stand by
elSB
0.0005
0.0005
0.0005
0.0005
0.0005
0.0005
kW
Type of heat output/room temperature
control
With distance control option
Room temperature control, with open window detection
Yes
Adaptive Start
Yes
With electronic room temperature control plus week timer
Yes
Contact details: Flamerite Fires Ltd. Greenhough Road, Lichfield. Staffs. WS13 7U
Information Requirements

19 | Page
Radia Flame
Nitra Flame
Wiring Diagrams