Flash Furniture GC-MBLK65-BK-GG User manual

ASSEMBLY INSTRUCTIONS
Before You Begin:
Customer Service Email: [email protected] | phone:[phone]
GC-MBLK65-BK-GG/GC-MBLK65-GY-GG/GC-MBLK65-WH-GG
65" Tr Door
TV Stand for up to 80" TVs
Thank you for your purchase!
Tighten all components securely before use. Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product or componenets may result.
CHOKING HAZARD - Small Parts. Adult Assembly Required.
DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE
Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware (where
included) to help prevent the unit from tipping and causing accidental injury, instability, death or damage. The tipping
restraint is intended only as a safety measure, it is not a substitute for proper adult supervision.
To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall Straps
suitable for the unit weight and wall materials (if not included) should be purchased and installed.
Online Assembly Instructions: http://ftp.flashfurniture.com/AssemblyInstructions/GC-MBLK65-WH-GG.pdf
Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the
components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching during
assembly.
Assembly Time
Load Bearing
60 min
LBS LBS LBS 200 LBS
LBS 30 LBS
LBS LBS LBS
LBS

Have a Question/Concern?
Quality products and first-class customer service are the cornerstone
of long-lasting consumer relationships. We strive toward excellence
in all we do and want you to be completely satisfied with your
purchase. Please contact our exceptional Customer Experience
Agents at the email address or phone number shown below to assist
you with any product questions or issues before requesting a return.
We look forward to serving you in a friendly, efficient manner to
resolve any issues you may have.
Customer Service Email: [email protected]
Customer Service Phone: [phone]
Our Warranty Statement
This warranty covers manufacturing defects associated with your new product. The product
is warranted from the original purchase date and to the original purchaser for normal usage,
according to the below-referenced specifications and limitations.
•Non-moving metal parts are warranted for 5 years.
•Component parts including pneumatic cylinder, control mechanism, base and casters are warranted for 2 years.
•All other items are warranted for 1 year.
Normal usage means use in compliance with the restrictions and weight limits specified for
the product. In the absence of product-specific restrictions and weight limits, normal usage
means use for no more than forty hours per week by persons weighing 250 lbs. or less.
Coverage terminates if the product is sold or otherwise transferred. Repairs made by parties
other than Belnick also void this warranty.
This warranty will not cover: (1) labor, freight, or damage from misuse, abuse, negligence,
alteration, assembly, installation, attachments, accident, vandalism, acts of nature or any
other event beyond the control of Belnick; (2) tearing, scratching, scuffing, or blemishing of
leather or fabric; (3) cosmetic damage that may result from normal usage; (4) damage
attributable to use by persons exceeding specified weight limits or commercial use
exceeding forty hours per week; or (5) rust or other damage caused by exposure to
moisture. The user assumes all risk of injury resulting from use of this product. Liability for
incidental or consequential damage is excluded. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion may
not apply to you.

PARTS
1（1） 1（11）1
C
1
1（2）
3.5*14
D
1（12）
1（3）
36+1E
1（13）
1（4）
8+1F
1（14）
2（5）
4G
2（15）
1（6）
2H
1（7）
12I1（16）
1
（8）
4J2（17）
1（9）
2KA
1（10）
B2L
Top Plate
Bottom Plate
Left Side Panel
Right Side Panel
Inner Supports
Left Front Fascia
Right Front Fascia
Left Rear Fascia
Right Rear Fascia
Cam Lock Covers
Door Handles
Door Handle Bolts
Back Panel Screws
Shelf Holders
Hinges
Door Strike Plate
Bottom Support
Feet
Lower Back Panel
Upper Back Panel
Dowel Pegs
Screw-In Pegs
Cam Locks
Front Doors
Front Upper Brace
Right Inner Support Fascia
Left Inner Support Fascia
Middle Shelf
Left & Right Shelves
32+1
32+1
18+1
32+1

STEP 1
STEP 2
Door Strike
Plates
3.5
Screws
Ensure groove opening
faces upwards
A*18
B*32
B
B
BB
B
B
B
B
B
B
BB
B
B
BB
B
B
B
BB
B
AA
AAAA
A
A
（1）
（2）
（3）
（4）
（5）
*2
（6）
（7）
（11）
（12）
（13）
（14）
A
A
A
A
B
B
B
B
B
B
B
B
B
B
K
K
E *2
E *2
A
（8）
A
K *2
E *4
Screw-In Pegs
Dowel Pegs
Top Plate
Right Side Panel
Right Inner Support Fascia
Left Front Fascia
Left Rear Fascia
Right Front Fascia
Right Rear Fascia
Inner Supports
（4）
（12）
（14）
C
C
C
C
Door Strike Plate Door Strike Plate
Dowel Peg
Dowel Peg
C*4
Arrow Side Toward Receiver Hole
Receiver Hole
Screw-In Peg
STEP 2B: Ensure Cam Locks (Part C) are
inserted in holes with open side facing
outwards toward receiver hole for Screw-In
pegs (Arrow Side). Insert Screw-In Pegs on the
Right Side Front Fascia (Part 12) into the Cam
Locks (Part D) on the Right Side Panel. Turn
Cam Locks clockwise to tighten.
STEP 2A: Ensure Cam Locks (Part C) are
inserted in holes with open side facing
outwards toward receiver hole for Screw-In
pegs (Arrow Side). Insert Screw-In Pegs on the
Right Side Rear Fascia (Part 14) into the Cam
Locks (Part D) on the Left Side Panel. Turn
Cam Locks clockwise to tighten.
Cam Lock
Front Upper Brace

STEP 3
STEP 4
E
*8
L
*2
（2）
L
E
*4
L
E
*4
Bottom Support Feet
3.5 Screws
Bottom Plate
STEP 3A: Attach Bottom Support Feet (Part L) to the
underside of Bottom Plate (Part 2) using (8) 3.5 Screws
STEP 3B: Attach Screw-In Pegs (Part B) to the
underside of Bottom Plate (Part 2)
（3）
（11）
（13）
C
C
C
C
STEP 2C: Ensure Cam Locks (Part C) are
inserted in holes with open side facing
outwards toward receiver hole for Screw-In
pegs (Arrow Side). Insert Screw-In Pegs on the
Left Side Rear Fascia (Part 13) into the Cam
Locks (Part D) on the Left Side Panel. Turn
Cam Locks clockwise to tighten.
Ensure groove opening
faces upwards
Left Side Panel
STEP 2D: Ensure Cam Locks (Part C) are
inserted in holes with open side facing
outwards toward receiver hole for Screw-In
pegs (Arrow Side). Insert Screw-In Pegs on the
Left Side Front Fascia (Part 11) into the Cam
Locks (Part D) on the Right Side Panel. Turn
Cam Locks clockwise to tighten.
C*4
Arrow Side Toward Receiver Hole
Receiver Hole
Screw-In Peg
Cam Lock

STEP 5
STEP 6
（8）
（9）
（10）
STEP 5: Insert Cam Locks (Part C) into the Upper Front Panel (Part
8)and ensure the arrow side is facing outwards. Slide the Screw-In Pegs
on the Left and Right Side Panels into the Cam Lock Receiver Holes in
the Bottom Plate and Upper Front Panel (Part 8). Turn Cam Locks
clockwise to tighten.
NOTE: Ensure grooves in side panels are at the back of the
unit and align with the grooves in the Bottom Plate
Ensure Door Strike Plates Are Facing Front of TV Stand
STEP 6: Align the Lower Back Panel (Part 10) with the grooves in the
Left and Right Side Panels and slide down until fully seated in the
grooves of the Bottom Plate. Repeat steps with the Upper Back Panel
(Part 9).
Lower Back Panel
Upper Back Panel
Grooves
（2）
（3）
（4）
C
C
C
C
C
C
C*6

STEP 7
STEP 8
（1）
（5）
C*4
STEP 7: Ensure Cam Locks (Part C) are
inserted in holes with open side facing
outwards toward receiver hole for Screw-
In pegs (Arrow Side). Slide Inner
Supports (Part 5) onto Long Screw-In
Pegs on the bottom plate. Turn the Cam
Locks (Part D) clockwise to tighten.
Note: Ensure side of Inner Supports
with 4 screw holes is facing the rear of
TV Stand
STEP 8A: Ensure Cam Locks (Part C) are inserted
in holes with open side facing outwards toward
receiver hole for Screw-In pegs (Arrow Side). Place
Top Plate (Part 1) onto the assembled frame.
Confirm that all Screw-In Pegs and Dowel Pegs that
were preassembled in STEP 1 are seated correctly.
The groove on the underside of the Top Plate
should be seated completely on the Upper Back
Panel. Turn the Cam Locks (Part D) clockwise to
tighten.
Top Plate
（5）
C
C
C
C*4
C*10

C*4
STEP 9
STEP 10
（6）
（7）
C
C
C
C
STEP 9: Insert Cam Locks (Part C) into holes
with arrow side pointing outwards. Insert
preassembled Screw-In Pegs on Left Fascia (Part
7)and Right Fascia (Part 6) into the Receiver
Holes and turn Cam Locks clockwise to tighten.
STEP 10: Cover all Cam Locks with Cam Lock Covers (Part D)
D*32
D
DD
D
D

STEP 11
STEP 12
G
G
G
G
G
J *4
E *8
E *16
（15）
（15）
J
E
*2
J
E
*2
J
E
*2
J
E
*2
H
H
H
STEP 11A: Attach Hinges (Part J) to the Front
Doors (Part 15) using (8) 3.5 Screws (Part E)
STEP 11B: Attach Door Handles (Part H) to
the Front Doors (Part 15) using (4) Door
Handle Screws (Part G)
Door Handle
Hinges
Door Handle Screws
Hinges
Door Handle Screws
Door Handle
STEP 12: Attach Front Doors (Part 15) to
pre-marked holes in TV Stand using (16)
3.5 Screws (Part E)
E *4
E *4
（15）
（15）

STEP 13
STEP 14
I *12
F *8
F
F
F
F
F
F
F
F
STEP 11: Insert Shelf Holders (Part I) into holes
at the desired height then place the Left & Right
Shelves (Part 17) and the Middle Shelf (Part 16)
onto Shelf Holders
STEP 14: Attach Upper and Lower Back
Panels to the Inner Supports using (8) Back
Panel Screws (Part F)
Back Panel Screws
Shelf Holders
（16）
（17）
（17）
I
I
I