HiB Novum Duet User manual

Thank you for purchasing this HiB product.
Please read through these instructions carefully and refer back to them during installation to ensure that
your product is fitted safely and that it retains its high quality finish.
Please retain this leaflet for future reference.
Before drilling, ensure there are no hidden cables or pipes in the wall.
FI #03 006 R170314 Ver No. 1.0 Mar 2017
Duet

2
Duet Vanity Units
1. Position the unit in a suitable location. Carefully mark the desired position of the unit using a so
pencil.
2. Using a spirit level, mark a horizontal line below the pencil mark, taking into account the location
of the furniture hangers. Bend and break the wall brackets as shown in Fig. 1 and place brackets
on the pencil line paying attention to the distance between the inner sides of the unit. Carefully
mark the position of the holes using a so pencil. (Fig. 2).
3. Before drilling, ensure there are no hidden cables or pipes behind the mounting
points. Using a suitable drill bit, drill holes in the marked positions to a suitable depth.
4. Insert wall plugs level with the surface of the wall. If fitting to a tiled surface, wall plugs should be
inserted below the tile surface to avoid cracking. NB. For plasterboard walls, specialist heavy
duty fixings should be purchased from any DIY or hardware store.
5. Fix the brackets to the wall using the screws provided (Fig. 2).
6. Hang the furniture unit, ensuring the claws on the hangers are securely located on the wall
brackets. Using a spirit level, make the unit level by adjusting screw B on the hangers (Fig. 3).
Once straight, tighten screw A until the unit is secure against the wall.
7. Remove the bottom drawer from the carcass by removing the securing screw on the underside of
the drawer runner (Fig. 7).
8. Using a spirit level, ensure that the side of the carcass is completely vertical, so that the unit is
sitting completely square. Now mark the drill locations in the centre of the metal brackets at the
bottom of the carcass (Fig. 4). Now remove the carcass from the wall.
9. Using a suitable drill bit, drill holes in the marked positions to a suitable depth. Insert wall plugs
level with the surface of the wall. If fitting to a tiled surface, wall plugs should be inserted below
the tile surface to avoid cracking. NB. For plasterboard walls, specialist heavy duty fixings
should be purchased from any DIY or hardware store.
10. Rehang ensuring unit is once again level.
11. Using the screws provided, fix the bottom brackets to the wall to secure the base of the carcass in
place (Fig 4).
12. Reinsert the drawer into the unit and secure in place with the screws removed previously. If
necessary, the drawer runners can be adjusted in order to align the drawer front(s), this is done by
turning the small adjuster wheel before tightening the securing screws (Fig. 5).
13.Lastly, mount the basin onto the furniture unit using a fine bead of silicone to seal the washbasin to
the unit and wall edges.

hib.co.uk 3
Fig. 1 Fig. 2
Fig. 3
Fig. 5
+
+
A
B
Fig. 4

©HiB Copyright: No part of this document may be reprinted or duplicated without HiB consent. All sizes and measurements are approximate, but we do try and
make sure they are as accurate as possible. In the interest of continuous product development, HiB reserves the right to alter specifications as necessary. E & OE.
T: [phone] F: [phone] E: [e-mail] hibnovum.co.uk
Building 3, North London Business Park, Oakleigh Road South, New Southgate, London. N11 1GN
Cleaning
To preserve the high quality finish of your HiB product, please ensure you regard the following care
and cleaning recommendations:
• Use only a so damp cloth.
• Wipe off all water spillages as soon as possible
• DO NOT USE any abrasives or solvents.
Aercare Service
In the unlikely event that this product should fail please contact HiB customer services, contact details
shown below.
Tall Units
1. Please note that the tall units can be mounted as both right hand
and le hand door opening.
2. Position the unit in a suitable location. Carefully mark the desired
position of the unit using a so pencil.
3. Using a spirit level, mark a horizontal line below the pencil mark,
taking into account the location of the split baton style furniture
hanger. Place mounting baton on the pencil line and carefully mark
the position of the holes using a so pencil. (Fig. 6).
4. Before drilling, ensure there are no hidden cables or pipes
behind the mounting points. Using a suitable drill bit, drill holes
in the marked positions to a suitable depth.
5. Insert wall plugs level with the surface of the wall. If fitting to a tiled
surface, wall plugs should be inserted below the tile surface to avoid
cracking. NB. For plasterboard walls, specialist heavy duty fixings
should be purchased from any DIY or hardware store.
6. Fix the mounting baton to the wall using the screws provided (Fig. 6).
7. Hang the tall unit onto the wall baton, ensuring that it is securely
seated.
8. If necessary, the door(s) can be adjusted to align them with the tall
unit carcass. This is done by adjusting the small screws on the hinges
(see Fig. 8).
9. In order to adjust the position of the shelves (please note that the
centre shelf is fixed and not removable), the doors must first be
removed (see Fig. 7). Once the door is removed, simply remove the
shelf studs and reinsert them in the required position. Replace doors.
Fig. 7
A B C
Fig. 8
Fig. 6