Southern Enterprises MS834100TX User manual

For assistance with assembly contact:
Southern Enterprises, Inc.
Customer Service 1-800- 33-509
[e-mail]
wwww.seidal.com
MS834100TX Dandridge TV/Media
Stand-Black
MS834200TX Dandridge TV/Media
Stand - Antique White
A
ssembly
I
nstruction
PO#：
Page 1

A.
Quantity
of 1
top panel
B.
Quantity
of 1
bottom panel
C.
Quantity
of 1
left side panel
D.
Quantity
of 1
right side panel
E.
Quantity
of 1
fix shelf panel
F.
Quantity
of 1
left fix shelf panel
G.
Quantity
of 1
right fix shelf panel
H.
Quantity
of 1
Right post
I.
Quantity
of 1
Left post
J.
Quantity
of 1
Left door
K.
Quantity
of 1
right door
L.
Quantity
of 1
adjustable shelf panel
M.
Quantity
of 1
drawer back
N.
Quantity
of 1
drawer side left
O.
Quantity
of 1
drawer side right
Dandridge TV/Media Stand
Parts list
Please review all parts and hardware before disposing of any packaging.
Call Customer Service if missing hardware.
Using a screw that is too long will cause damage.
Before beginning assembly separate each type of screw. Carefully study the
diagrams below. You may receive extra hardware with your unit
Page 2

P
Quantity
of 1
drawer bottom
Q
Quantity
of 1
drawer Front
R
Quantity
of 1
Upper back panel
S
Quantity
of 1
Below back panel
T
Quantity
of 6
leg
1
Quantity
of 26
Wood Dowel
Dia5/16”x1-3/16”L
2
Quantity
of 20
cam blot
3
Quantity
of 20
calm lock
4.
Q
uantity
of 4
screw: Dia1/8”x1”L
5.
Quantity
of 20
screw :Dia1/8”x5/8”L
.
Quantity
of 2
Magic door catch
7.
Quantity
of 4
knob
8.
Quantity
of 4
Small bolt
9.
Quantity
of 4
Shelf pin
Page 3

10.
Quantity
of 24
Paper cover
11.
Quantity
of 4
bracket
12.
Quantity
of 12
screw :Dia1/8”x1/2”L
13.
Quantity
of 1
Female slide left
14.
Quantity
of 1
male slide left
15.
Quantity
of 1
Female slide right
1 .
Quantity
of 1
male slide right
17.
Quantity
of
4
Plastic Anchor
18.
Quantity
of 4
screw :Dia1/8”x1-5/8”L
19.
Quantity
of 4
screw :Dia1/8”x5/8”L
20.
Quantity
of 2
Plastic chain
Care and Cleaning Instructions:
Before using wipe with a clean dry cloth.
Periodically apply furniture wax to renew
the finish. Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replac
ement parts or questions please
Call Customer Service at 1-800-633-5096
please call Manufacturer for assistance questions or
Parts.
Assembly Tool Required No.2 Phi
Tool List: 3/1 " drill bit, drill, tape measure and pencil.
Page 4
Assembly Tool Required No.2 Phillips
Screwdriver (Not included)

Figure 1
Assembly Instructions:
Wood may scratch easily, Be careful
when assembling. Do not scratch.
Attach female slide left (13) to
left side panel(C) with screw
(12).
Tighten screw with phillips
screwdriver (not included)
Figure 2
Attach female slide right (15)
to right side panel (D) with
screw (12)
tighten screw with phillips
screwdriver(not included)
E
C
D
3
3
3
3
10
10
10
10
1
2
Figure 3
Insert cam lock (
3
) into
predrilled holes on fixed shelf
panel (E)
Screw cam bolt (2) into
pre-drilled holes on left side
panel (C). Attach left side panel
(C) to fixed shelf panel (E) by
inserting wood dowel (1) & cam
bolt (2) into corresponding
pre-drilled holes until left side
panel (C)& fixed shelf panel (E)
meet. Tighten by rotating cam
lock (3) clockwise with Phillips
screwdriver (not included)
Repeat with right side panel (D)
Cover cam lock holes with paper
cover(10)
Dandridge TV/media Stand
Assembly Instructions
P
age 5
15
12
12
12
D
13
12
12
12
C

T
TT
TT
T
B
Figure 4
Attach legs (T) to pre-assembly
unit on figure 3. Tighten by your
hand.
Figure 5
Insert cam lock (
3
) into
predrilled holes on on
pre-assembly unit on figure
3.Screw cam bolt (2) into
pre-drilled holes on bottom
panel (B). Attach pre-assembly
unit on figure 3 to bottom panel
(B) by inserting wood dowel (1)
& cam bolt (2) into
corresponding pre-drilled holes
until pre-assembly unit on
figure 3 & bottom panel
(B)meet. Tighten by rotating
cam lock (3) clockwise with
Phillips screwdriver (not
included)
Cover cam lock holes with paper
cover(10)
Figure
Insert Wood Dowel (
1
) into
predrilled holes on pre-assembly
unit on figure 5
Attach two side fix shelf panel
(F)(G) to pre-assembly unit on
figure 5 by your hand .
Page 6
3
2
1 0
1
1
2
3
1 0
F

Figure 7
Insert cam lock
(
3
) into
predrilled holes on post (H)&(I)
Screw cam bolt (2) into
pre-drilled holes on
pre-assembly unit on figure 6.
Attach two post (H)(I) to
pre-assembly on figure 6 by
inserting wood dowel (1) & cam
bolt (2) into corresponding
pre-drilled holes until post (H)(I)
& pre-assembly unit on figure 6
meet.
Tighten by rotating cam lock (3)
clockwise with Phillips
screwdriver (not included)
Cover cam lock holes with paper
cover(10)
J
K
7
Figure 8
Attach two door(J)(K) to
pre-assembly on figure7 by
hand
Attach handle (7) to door with
small bolt (8).
Tighten small bolt (8)with
Phillips screw driver (not
included)
Figure 9
Attach magic door catch (7)to
top panel (A)with screw (5)
Tighten screw with Phillips screw
driver (not included).
Page 7
5
7
7
A
5
55

Figure 10
Insert cam lock
(
3
) into
predrilled holes on
pre-assembly unit on figure 9
Screw cam bolt (2) into
pre-drilled holes on
Top panel (A) to pre-assembly
on figure 9 by inserting wood
dowel (1) & cam bolt (2) into
corresponding pre-drilled holes
until Top panel (A) &
pre-assembly unit on figure 9
meet.
Tighten by rotating cam lock
(3) clockwise with Phillips
screwdriver (not included)
Cover cam lock holes with
paper cover(10)
Figure 11
A
ttach upper
back panel(R)&
below back panel (S) to
pre-assembly unit on figure 10
with screw (5)
Tighten screw with Phillips
screwdriver(not included)
Figure 12
I
nsert shelf pin(9) into
pre-drilled holes on
pre-assembly unit on figure 11
Put adjustable shelf (L) on shelf
pin as shown.
Page 8
S
5
5
5
55
5
5
5
55
5
R
9
L
1
1
1
1
3
3
2
A
1
12
10
10
22
1
1
22
3
10
3
10

Figure 13
M
4
4
10
4
4
10
10
10
N
I
nsert calm lock(
3
) into
predrilled hole on drawer side
panel left (N)& drawer side
panel right (O) screw calm
bolt(2) into predrilled on
drawer front panel(Q)
Attach the drawer side panel
left (N) & drawer side panel
right (O) to drawer front
panel(Q) together by groove
well match as well tight them
by rotating cam lock (3)
clockwise with Phillips
screwdriver (not included)
Cover cam lock holes with
paper cover(10)
Put the Drawer Bottom Panel(P)
into inner grooves of Drawer
Side Panels(O N) and Drawer
Face Panel(Q).
Use screw(4) to connect drawer
back pane(M) to two drawer side
panel tighten screw(1) with
Philip screwdriver(not included)
Cover all holes with paper
cover(10)
16
12 14
12 12
12
12
12
Figure 14
Attach male slide left (14)&
male slide right (16) to
pre-assembly unit on figure 13
with screw (12)
Tighten screw with Phillips
screwdriver (not included).
Page 9
N
8
Q

Figure 15
Attached drawer box into
pre-assembly unit on figure 14
please make sure drawer box
side’s male slide into side
panel’s female slide please try
and make sure slide smoothly.
Figure 1
Attach Bracket (11) to back
Panel using Screw (19).
Tighten screw (19) using
Philips screwdriver.
Mark two desired locations on
wall. Drill two 3/16" holes on
wall. Insert plastic anchors
(17) into the 2 holes on wall as
shown. (When doing this you
will need a hammer help you).
Then attach the Bracket (11) to
wall using screw (18). Tighten
screws (18) using Philips screw
driver.
Move this item close to the wall
Bracket (11) and tie in both
Bracket (11) with Plastic Chain
(20) as shown in diagram.
Anti-tipping hardware must
be used for this product to
avoid tipping and injury.
Page 10
wall
11
17
11
17
18
18
11
19
19

Figure 17
Y
ou
DANDRIDGE
TV/MEDIA
STAND=BLACK is ready to use
Page 11

Please immediately examine this product carefully. Any request for missing parts or damage replacement must
be received within 90 days of your receipt of the product. Replacement, if available, will be honored within this
time frame.Parts will not be available for items arriving fully assembled. We do not recommend modifying
product(s) and we are not responsible for any damages due to product modification(s). If damages or missing
parts are not reported within 90 days of your receipt, we are under no obligation to provide parts or replacement
merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri Central
time if you have product issues or email us at [e-mail]. Please ask for customer service
representative for issues involving damages or replacement parts. Please ask for technical assistance
representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Parts Replacement Form
Customer Service 1-800-633-5096
[e-mail]
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019
Page 12

CAUTION
The top shelf is intended for a flat screen television with a maximum overall width of 50” and
supports up to 175 lb.
The top shelf is NOT INTENDED for tube televisions.
Each center shelf should not be loaded with more than 20 lb. Each side shelf should not be
loaded with more than 15 lb. Each drawer box should not be loaded with more than 10 lb.
DO NOT EXCEED RECOMMENDED LOAD. Use with products heavier than the
maximum sizes and weights indicated may result in instability causing possible injury.
This unit contains a permanent warning sticker located on under side of top shelf or inside
drawer.
Do not allow children under 16 years to move the cart.
Model: MS834100TX
Dandridge TV/Media Stand
Southern Enterprises Inc
600 Freeport Parkway
Suite 200 Coppell Texas 75019
Manufacture Date: 01/20/2014
Page 13