Flash Furniture CO-6-RED-GG User manual

Thank you for your purchase!
Square Indoor-Outdoor
Steel Patio Table
Customer Service Email: [email protected] | Phone: [phone]
CO-6-RED-GG / CO-6-BK-GG / CO-6-GD-GG / CO-6-SIL-GG / CO-6-SKY-GG / CO-6-WH-GG
ASSEMBLY INSTRUCTIONS
Before You Begin:
Please identify allcomponent parts and hardware pieces required before you begin. Carefully remove allof the
components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching
during assembly.
Caution:
Tighten all components securely before use.Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product orcomponents may
result.
Warning:
CHOKING HAZARD - Small Parts. Adult Assembly Required.
DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE
Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware (where
included) tohelp prevent the unitfrom tipping and causing accidental injury, instability, death or damage. The
tipping restraint isintended only as a safety measure, itisnot a substitute for proper adultsupervision.
To help prevent furniture from tipping over itmust be permanently attached to the wall. Anti-Tip Safety Wall Straps
suitable for the unit weight and wall materials (if not included) should be purchased and installed.
Online Assembly Instructions: http://ftp.flashfurniture.com/AssemblyInstructions/CO-6-GD-GG.pdf

Have a Question/Concern?
Quality products and first-class customer service are the cornerstone of long-
lasting consumer relationships. We strive toward excellence in all we do and
want you to be completely satisfied with your purchase.
Please contact our exceptional Customer Experience Agents at the email
address or phone number shown below to assist you with any product
questions or issues before requesting a return.
We look forward to serving you in a friendly, efficient manner to resolve any
issues you may have.
Customer Service Email: [e-mail]
Customer Service Phone: [phone]
Our Warranty Statement
This warranty covers manufacturing defects associated with your new product. The product
is warranted from the original purchase date and to the original purchaser for normal
usage, according to the below-referenced specifications and limitations.
•Non-moving metal parts are warranted for 5 years.
•Component parts including pneumatic cylinder, control mechanism, base and casters
are warranted for 2 years.
•All other items are warranted for 1 year.
Normal usage means use in compliance with the restrictions and weight limits specified for
the product. In the absence of product-specific restrictions and weight limits, normal usage
means use for no more than forty hours per week by persons weighing 250 lbs. or less.
Coverage terminates if the product is sold or otherwise transferred. Repairs made by
parties other than Belnick also void this warranty.
This warranty will not cover: (1) labor, freight, or damage from misuse, abuse, negligence,
alteration, assembly, installation, attachments, accident, vandalism, acts of nature or any
other event beyond the control of Belnick; (2) tearing, scratching, scuffing, or blemishing of
leather or fabric; (3) cosmetic damage that may result from normal usage; (4) damage
attributable to use by persons exceeding specified weight limits or commercial use
exceeding forty hours per week; or (5) rust or other damage caused by exposure to
moisture. The user assumes all risk of injury resulting from use of this product. Liability for
incidental or consequential damage is excluded. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion may
not apply to you.

PARTS
STEP 1
Legs
Table Top
Allen Wrench
Open End
Wrench
Leg
Connector
Screw Washer Screw Nut
STEP 1: Lay Table Top (Part A) face down
on a smooth, clean surface. Attach (4) Legs
(Part B) to Table Top using (4) ø16 Washers
and (4) M8*15 Screws. Ensure curves are
facing inward.
NOTE: Do not
tighten screws
completely
ø16 Washer
Allen Wrench
M8*15 Screws
Legs
Curves
Curves
STEP 2A: Attach Middle Leg Connector Brace (Part E) to the Legs
using (8) M8*40 Screws (Part H) and (8) Nuts (Part I). Return
assembled table to the upright position, level the legs, and securely
tighten the 4 table top screws from step 1.
Middle Leg
Connector
Brace
STEP 2B: Using the Open End Wrench (Part D) to hold
the nut and the Allen Wrench (Part C) to turn the screws,
securely tighten legs to the Middle Leg Connector Brace.
Open End Wrench
Nut
M8*40 Screws
Allen Wrench
STEP 2