Flomec TM Series User manual

TM Series®Electronic
Water Flowmeters
Product Owner’s Manual EN
920786-02 Rev D07/16/2020
1/2 INCH - 2 INCH METER SIZES
[TM05XXXXXX - TM20XXXXXX MODELS]

Please save these instructions for future reference. Read carefully before attempting
to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply
with instructions could result in personal injury and/or property damage.
Please refer to back cover for information regarding this product’s warranty and
other important information.
SAVE FOR YOUR RECORDS
Model #: ___________________
Serial #: ___________________
Purch. Date: _______________
DO NOT RETURN THIS PRODUCT TO THE STORE!
Please contact Great Plains Industries, Inc.®before returning any product. If you are
missing parts, or experience problems with your installation, contact our Customer
Support Department. We will be happy to assist you.
Call: 888-996-3837 or 316-686-7361
Email: [email protected]

3
SAFETY /
SPECIFICATIONS
ASSEMBLY /
INSTALLATION
OPERATION /
CALIBRATION
MAINTENANCE /
REPAIR
GETTING STARTED
BEFORE YOU BEGIN
Usage Requirements
• Use TM Series meters with water and other chemicals compatible
with wetted components.
• DO NOT use to meter fuel or incompatible chemicals.
• TM Series meters are very sensitive to electric noise if operated
within 1 to 2 inches of some electric motors or other sources of
electronic noise.
• This meter is not legal for trade applications.
UNPACKING/INSPECTION
Inspect
• After unpacking the unit, inspect carefully for any damage that may
have occurred during transit. Check for loose, missing or damaged
parts. Shipping damage claims must be led with carrier.
• See General Safety Instructions, and all Cautions, Warnings, and
Dangers as shown.
tools.eps
box.eps
magnify_2.eps
warning symbol.eps
measure.eps
plug.eps
oil.eps
megaphone.eps
biohaz.eps
Battery_Caution1.eps
Caution.eps
Crush_Caution1.eps
Electrical_Caution.eps
Face_protection.eps
Fall_Hazard.eps
Fall_protection.eps
GearHand_Hazard.eps
Head_protection.eps
Heavy_Hazard.eps
Hot_surface.eps
Recycle.eps
Resp_protection1.eps
Resp_protection2.eps
Temp_Caution1.eps
body_protection.eps
chemical_Caution.eps
ear_protection1.eps
explosive_caution.eps
eye_protection1.eps
foot_protection.eps
hand_protection.eps
tools.eps
box.eps
magnify_2.eps
warning symbol.eps
measure.eps
plug.eps
oil.eps
megaphone.eps
biohaz.eps
Battery_Caution1.eps
Caution.eps
Crush_Caution1.eps
Electrical_Caution.eps
Face_protection.eps
Fall_Hazard.eps
Fall_protection.eps
GearHand_Hazard.eps
Head_protection.eps
Heavy_Hazard.eps
Hot_surface.eps
Recycle.eps
Resp_protection1.eps
Resp_protection2.eps
Temp_Caution1.eps
body_protection.eps
chemical_Caution.eps
ear_protection1.eps
explosive_caution.eps
eye_protection1.eps
foot_protection.eps
hand_protection.eps

MAINTENANCE /
REPAIR
OPERATION /
CALIBRATION
ASSEMBLY /
INSTALLATION GETTING STARTED
4
SAFETY /
SPECIFICATIONS
GENERAL SAFETY INSTRUCTIONS
IMPORTANT: It is your responsibility to:
• Ensure that all equipment operators have access to adequate
instructions concerning safe operating and maintenance
procedures.
Compatibility of this product’s material and the process fluid
and/or environment should be considered prior to putting into
service.
Product should never be operated outside its published
specifications for temperature or pressure. See specifications for
your model.
Make sure flow and pressure have been eliminated from process
pipe prior to installing or removing product.
Always use appropriate thread sealant or flange gaskets when
connecting product to process piping.
To protect against leakage, seal all pipe threads with an
appropriate sealing compound. Make sure the sealing compound
does not intrude into the flow path.
NOTE: If connecting to new male pipe threads, burrs and curls
can adversely affect accuracy. Correct the problem prior to turbine
installation.
Installation near high electromagnetic fields and high current
fields is not recommended and may result in inaccurate
readings.

5
GETTING STARTED ASSEMBLY /
INSTALLATION
OPERATION /
CALIBRATION
MAINTENANCE /
REPAIR
SAFETY /
SPECIFICATIONS
SPECIFICATIONS
TM05 -
1/2 INCH
TM07 -
3/4 INCH
TM10 -
1 INCH
TM15 -
1-1/2 INCH TM20 - 2 INCH
Type Turbine Flowmeter
Unit of
Measure Gallon or Litre
Flow Range 1-10 GPM
3.8-38 L/min
2-20 GPM
7.6-76 L/min
5-50 GPM
19-190 L/min
10-100 GPM
38-380 L/min
20-200 GPM
76-760 L/min
Accuracy w/
Computer +/- 3.0% of Reading (Accuracy can be improved with eld calibration)
Max.
Working
Pressure
225 PSIG @ 73°F (15.5 bar @ 23°C);
BSP - 150 PSIG @ 73°F (10.3 bar @ 23°C)
Operating
Temperature +32°F to +140°F (0°C to +60°C) - Do not allow uid to freeze inside meter
Storage
Temperature -40°F to +140°F (-40°C to +60°C)
Field
Calibration Yes
Wetted
Components
Housing: PVC | Journal bearings: Ceramic | Shaft: Tungsten carbide
Rotor and supports: PVDF | Retaining washer: Stainless steel
Inlet / Outlet Connections
TM05 TM07 TM10 TM15 TM20
S - (SPIGOT) 1/2 inch Schd. 80 3/4 inch Schd. 80 1 inch Schd. 80 1-1/2 inch
Schd. 80 2 inch Schd. 80
N - (NPT) 1/2 inch NPT 3/4 inch NPT 1 inch NPT 1-1/2 inch NPT 2 inch NPT
B - (BSP) N/A N/A 1 inch BSP 1-1/2 inch BSP 2 inch BSP
Weight
S - (SPIGOT) 0.38 lbs.
(0.172kg)
0.43 lbs.
(0.195kg)
0.49 lbs.
(0.222kg)
0.66 lbs.
(0.299kg)
0.78 lbs.
(0.354kg)
N - (NPT) 0.55 lbs.
(0.249kg)
0.67 lbs.
(0.304kg)
0.84 lbs.
(0.381kg)
1.38 lbs.
(0.628kg)
1.78 lbs.
(0.807kg)
B - (BSP) N/A N/A 0.84 lbs.
(0.381kg)
1.47 lbs.
(0.666kg)
1.93 lbs.
(0.875kg)
Weight shown is with computer display. Output modules add 0.30 lbs/0.14 kg

OPERATION /
CALIBRATION
ASSEMBLY /
INSTALLATION GETTING STARTED
6
SPECIFICATIONS (CONTINUED)
TM Meter
Size & Fitting Length (A) Height (B) Width (C)
Dimensions
TM05S - Spigot 4.3 in.
(109 mm)
2.5 in.
(63 mm)
2.1 in.
(53 mm)
TM05N - NPT 6.0 in.
(152 mm)
2.7 in.
(68 mm)
2.1 in.
(53 mm)
TM07S - Spigot 4.4 in.
(112 mm)
2.7 in.
(68 mm)
2.1 in.
(53 mm)
TM07N - NPT 6.1 in.
(155 mm)
2.9 in.
(73 mm)
2.1 in.
(53 mm)
TM10S - Spigot 4.5 in.
(114 mm)
2.9 in.
(73 mm)
2.1 in.
(53 mm)
TM10N - NPT 6.5 in.
(165 mm)
3.1 in.
(79 mm)
2.1 in.
(53 mm)
TM10B - BSP 6.7 in.
(170 mm)
3.1 in.
(79 mm)
2.1 in.
(53 mm)
TM15S - Spigot 5.4 in.
(137 mm)
3.6 in.
(91 mm)
2.1 in.
(53 mm)
TM15N - NPT 7.6 in.
(193 mm)
3.8 in.
(96 mm)
2.3 in.
(58 mm)
TM15B - BSP 7.6 in.
(193 mm)
3.7 in.
(94 mm)
2.2 in.
(56 mm)
TM20S - Spigot 5.5 in.
(140 mm)
4.1 in.
(104 mm)
2.4 in.
(61 mm)
TM20N - NPT 7.9 in.
(200 mm)
4.4 in.
(112 mm)
3.5 in.
(89 mm)
TM20B - BSP 7.8 in.
(198 mm)
4.2 in.
(107 mm)
2.7 in.
(69 mm)


SAFETY /
SPECIFICATIONS
Figure 1
C
B
A
MAINTENANCE /
REPAIR

7
GETTING STARTED ASSEMBLY /
INSTALLATION
OPERATION /
CALIBRATION
SAFETY /
SPECIFICATIONS
Figure 2
MAINTENANCE /
REPAIR
INSTALLATION
IMPORTANT: TM Series meters are available with either a computer for
local electronic display, or three versions of output modules (see PARTS
section of this manual) to provide a digital signal to customer interfacing
equipment. TM Series meters with computer display ship pre-configured
from the factory in either gallons or liters. The volume unit can be changed
to several other options. Refer to the Q9 owner’s manual for details on
changing or customizing the volume unit.
Connections
Install your meter in-line either horizontally or vertically. Installation to metal
connections is not recommended. Install as follows:
1. Plan to install turbine with a minimum straight pipe length as follows
(see Figure 2):
• Upstream from the turbine, allow a minimum straight pipe length of 10
times the internal diameter of the turbine.
• Downstream from the turbine, allow a minimum straight pipe length of
5 times the internal diameter of the turbine.
2. For Spigot (Pipe) End use only primer and solvents approved for PVC
gluing.
For NPT and BSP Fittings wrap all connections with 3 to 4 wraps of thread
tape (optional to use pipe thread sealant). Make sure the tape does not
intrude into the flow path.
3. Attach meter with arrow pointed in the direction of fluid flow.
4. For NPT and BSP Fittings - Hand tighten the meter at the housing ends.
Do not use a wrench or similar tool to tighten. This can damage the
housing.
Direction of Flow
UPSTREAM
10X I.D.
DOWNSTREAM
5X I.D.

8
SAFETY /
SPECIFICATIONS GETTING STARTED
OPERATION /
CALIBRATION
ASSEMBLY /
INSTALLATION
MAINTENANCE /
REPAIR
OPERATION / CALIBRATION
Verify Meter Accuracy
Before using, check the meter’s accuracy and verify calibration.
1. Make sure there is no air in the system by starting the flow until it runs
steadily. Then, stop or divert the flow using a valve or nozzle
2. Meter an exact known volume into an accurate container. For best
results, meter with one continuous full stream.
3. Check the volume against the display or recording equipment. If the
amount metered is accurate, further calibration is not necessary. If not,
refer to the Q9 Owner’s Manual (Non-Agency) Field Calibration Section
for further instructions (see below).
NOTE: Make sure you meet the meter’s minimum flowrate requirements:
You can download the Q9 Owner’s Manual (Non-Agency) here:
or visit FLOMECmeters.com to download owner’s manuals and other
technical documents.
TM Series Meter Minimum Flowrate
TM05 - 1/2 inch 1 GPM (3.8 L/min)
TM07 - 3/4 inch 2 GPM (7.5 L/min)
TM10 - 1 inch 5 GPM (18.8 L/min)
TM15 - 1-1/2 inch 10 GPM (37.5 L/min)
TM20 - 2 inch 20 GPM (75 L/min)

9
GETTING STARTED OPERATION /
CALIBRATION
SAFETY /
SPECIFICATIONS
ASSEMBLY /
INSTALLATION
MAINTENANCE /
REPAIR
MAINTENANCE
NOTE: Proper handling and care will extend the life and service of the meter
Turbine Rotor
The meter is virtually maintenance-free. However, it is important the rotor moves freely.
Keep the meter clean and free of contaminants.
If the rotor does not turn freely, apply a penetrating lubricant on the rotor, shaft and bearings.
Remove any debris or deposits from the rotor using a soft brush or small probe. Be careful
not to damage the turbine rotor or supports.
Blowing compressed air through the turbine assembly
could damage the rotor.
Do not allow liquids to dry inside the turbine.
Handle the rotor carefully. Small scratches or nicks can
affect accuracy.

OPERATION /
CALIBRATION
ASSEMBLY /
INSTALLATION
SAFETY /
SPECIFICATIONS GETTING STARTED
10
PARTS & SERVICE
For warranty consideration, parts, or other service information, please
contact your local distributor. If you need further assistance, contact
the GPI Product Support Department in Wichita, Kansas, during
normal business hours.
A toll free number is provided for your convenience.
1-888-996-3837
To obtain prompt, efficient service, always be prepared with the following
information:
• The model number of your meter.
• The serial number or manufacturing date code of your meter.
• Part descriptions and numbers.
For warranty work, always be prepared with your original sales slip or other
evidence of purchase date.
PARTS / ACCESSORIES LIST FOR TM SERIES METERS
Part Number Description
116000-1 Calibration container, Large (5 gallon)
901002-52 Seal
113435-10 Conditioned Signal Module (GEN 2)
125060-10 Pulse Access/External Power/Scaled Module (GEN 2)
125100-10 4-20mA Module
IMPORTANT: Please contact GPI before returning any parts. It may be
possible to diagnose the trouble and identify needed parts in a telephone
call.
This product is in compliance with the RoHS
Directive of the European Parliament and of the
Council on the Restriction of the Use of Certain
Hazardous Substances in Electrical and Electronic
Equipment.
Environmental Rating: IP65
MAINTENANCE /
REPAIR
Do not return this product without prior approval from the GPI Product
Support Department. Due to strict government regulations, GPI cannot
accept parts unless they have been drained and cleaned.
WEEE DIRECTIVE ROHS COMPLIANT (2011/65/EU)

11
GETTING STARTED SAFETY /
SPECIFICATIONS
ASSEMBLY /
INSTALLATION
OPERATION /
CALIBRATION
MAINTENANCE /
REPAIR
NOTES

© 2020 Great Plains Industries, Inc., All Rights Reserved.
Great Plains Industries, Inc. / 888-996-3837 / FLOMECmeters.com
FLOMEC®TWO-YEAR LIMITED WARRANTY
Great Plains Industries, Inc. 5252 E. 36th Street North, Wichita, KS USA 67220-3205,
hereby provides a limited warranty against defects in material and workmanship on all
products manufactured by Great Plains Industries, Inc. This product includes a 2 year
warranty. Manufacturer’s sole obligation under the foregoing warranties will be limited
to either, at Manufacturer’s option, replacing or repairing defective Goods (subject
to limitations hereinafter provided) or refunding the purchase price for such Goods
theretofore paid by the Buyer, and Buyer’s exclusive remedy for breach of any such
warranties will be enforcement of such obligations of Manufacturer. The warranty shall
extend to the purchaser of this product and to any person to whom such product is
transferred during the warranty period.
The warranty period shall begin on the date of manufacture or on the date of
purchase with an original sales receipt. This warranty shall not apply if:
A. the product has been altered or modified outside the warrantor’s duly appointed
representative;
B. the product has been subjected to neglect, misuse, abuse or damage or has been
installed or operated other than in accordance with the manufacturer’s operating
instructions.
To make a claim against this warranty, contact the GPI Customer Service Department at
316-686-7361 or 888-996-3837.
Or by mail at:
Great Plains Industries, Inc.
5252 E. 36th St. North
Wichita, KS, USA 67220-3205
The company will step you through a product troubleshooting process to determine
appropriate corrective actions.
GREAT PLAINS INDUSTRIES, INC., EXCLUDES LIABILITY UNDER THIS WARRANTY
FOR DIRECT, INDIRECT, INCIDENTAL AND CONSEQUENTIAL DAMAGES INCURRED
IN THE USE OR LOSS OF USE OF THE PRODUCT WARRANTED HEREUNDER.
The company herewith expressly disclaims any warranty of merchantability or fitness for
any particular purpose other than for which it was designed.
This warranty gives you specific rights and you may also have
other rights which vary from U.S. state to U.S. state.
Note: In compliance with MAGNUSON MOSS CONSUMER WARRANTY ACT –
Part 702 (governs the resale availability of the warranty terms).
920786-02 Rev D07/16/2020
IP65
2011/65/EU