FLORABEST FARM 40-Li A1 User manual

AKUMULATORSKA KOSILNICA
Navodila za uporabo in varno delo
Prevod izvirnih navodil
CORDLESS LAWNMOWER
Operation and Safety Notes
Translation of the original instructions
AKUMULÁTOROVÁ KOSAČKA NA TRÁVU
Návod na obsluhu a bezpečnostné pokyny
Preklad pôvodného návodu na použitie
AKKU-RASENMÄHER
Bedienungs- und Sicherheitshinweise
Originalbetriebsanleitung
AKU SEKAČKA NA TRÁVU
Obsluha a bezpečnostní pokyny
Překlad původního návodu k používání
AKKUS FŰNYÍRÓ
Üzemeltetési és biztonsági megjegyzések
Eredeti használati utasítás fordítása
OWIM GmbH & Co. KG
Stiftsbergstraße 1
DE-74167 Neckarsulm
GERMANY
Model No.: HG03586
Version: 02/2018
CORDLESS LAWNMOWER FARM 40-Li A1
IAN 292278IAN 292278
GB Operation and Safety Notes Page 5
HU Üzemeltetési és biztonsági megjegyzések Oldal 22
SI Navodila za uporabo in varno delo Stran 41
CZ Obsluha a bezpečnostní pokyny Strana 58
SK Návod na obsluhu a bezpečnostné pokyny Strana 74
DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 91

B
17
17c
17a
17b C
18d
18c
18b
18a
18
D
2x
3
10a
10b
F
14
3
12
E
2x
2
3
13a
13b
13c
G
4.
17a7b
7c
7
17
J
6
I4
9
11a11
K1
16
15
11b
A
H
7a
7b
7c
16
15
14
13
12
11
11a
10
9
3
6
7
4
5
1
2
8
19

Table of contents
List of pictograms used......................................................................................................... Page 6
Introduction ............................................................................................................................... Page 7
Intended use .................................................................................................................................. Page 7
Parts description............................................................................................................................. Page 7
Scope of delivery........................................................................................................................... Page 7
Technical data................................................................................................................................ Page 8
Safety warnings ...................................................................................................................... Page 9
Safe operating practices for electrically powered lawnmowers..................................................... Page 9
Vibration and noise reduction........................................................................................................ Page 12
Behaviour in emergency situations................................................................................................. Page 12
Residual risks.................................................................................................................................. Page 12
Battery charger safety warnings .................................................................................................... Page 12
Initial use..................................................................................................................................... Page 13
Unpacking ..................................................................................................................................... Page 13
Accessories .................................................................................................................................... Page 14
Assembly........................................................................................................................................ Page 14
Before use .................................................................................................................................. Page 14
Charging the battery pack............................................................................................................. Page 14
Checking the battery charging level .............................................................................................. Page 15
Safety key ...................................................................................................................................... Page 15
Attaching / removing the battery pack.......................................................................................... Page 15
Operation................................................................................................................................... Page 15
Grass collector............................................................................................................................... Page 15
Mulch plug..................................................................................................................................... Page 16
Adjusting the cutting height............................................................................................................ Page 16
Switching on and off...................................................................................................................... Page 17
Mowing ......................................................................................................................................... Page 17
After use......................................................................................................................................... Page 17
Cleaning and care ................................................................................................................... Page 17
Cleaning ........................................................................................................................................ Page 18
Maintenance.................................................................................................................................. Page 18
Repair ............................................................................................................................................ Page 18
Storage .......................................................................................................................................... Page 18
Transportation................................................................................................................................ Page 18
Troubleshooting....................................................................................................................... Page 18
Disposal....................................................................................................................................... Page 19
Service ......................................................................................................................................... Page 20
Warranty .................................................................................................................................... Page 20
Translation of original declaration of conformity..................................................... Page 21
5GB

List of pictograms used:
Read the instruction manual. Wear hearing protection!
Wear eye protection!
Caution / Warning Wear protective gloves!
Remove all packaging materials and
shipping devices. Wear non-skit safety shoes!
Packaging materials are not toys. Beware of sharp blades. Blades continue to
rotate after the motor is switched off
Remove disabling device before
maintenance
Switch the appliance off and remove the
battery pack. Keep bystanders away!
Protect the electrical parts against moisture. Do not expose the product to rain or wet
conditions.
Do not operate the product with wet hands
or while standing on a wet floor. Do not
touch the power plug with wet hands.
Risk of injury from ejected objects.
Protection class II Blades continue to rotate after the motor is
switched off
Alternating current
STOP
Grass collector full
Direct current
GO
Grass collector ready
T5A Fuse No load speed n0
45
Protect the battery pack against heat and
continuous intense sunlight. Cutting width
45
Protect the battery pack against water and
moisture. Lift with two persons.
Protect the battery pack from fire. For indoor use only
Guaranteed sound power level in dB
6 GB

CORDLESS LAWNMOWER
FARM 40-Li A1
Q Introduction
We congratulate you on the purchase of your
new product. You have chosen a high quality
product. The instructions for use are part of the
product. They contain important information
concerning safety, use and disposal. Before using
the product, please familiarise yourself with all
of the safety information and instructions for use.
Only use the product as described and for the
specified applications. If you pass the product on
to anyone else, please ensure that you also pass
on all the documentation with it.
Q Intended use
This cordless lawnmower (hereinafter “product”
or “power tool”) is designed for mowing
domestic lawns and grass areas.
The product is to be used by adults.
Any other use or modification of the product
are considered improper use and can result in
hazards such as death, life-threatening injuries
and damage. The manufacturer is not liable
for any damages caused by improper use. The
product is not intended for commercial or any
other use.
Q Parts description
Figure A/D/E:
1Handle
2Upper bar
3Lower bar (x2)
4Discharge cover
5Carrying handle
6Height adjustment lever
7Battery compartment cover
7a Battery pack connector
7b Safety keyhole
7c Safety key
8Wheel (x4)
9Housing
10 Lower bar mounting set (x2)
10a Washer
10b Lever
11
Grass collector
11a Carrying handle
11b Fill indicator flap
12
Cable clip
13 Upper bar mounting set (x2)
13a Bolt
13b Washer
13c Lever
14 Control cable
15
Lock-off button
16
On / off switch
Figure B:
17 Battery pack
17a Release button
17b Battery level indication lights
17c Battery level button
Figure C:
18 Rapid battery charger
18a Power cord with plug
18b Battery pack connector
18c Charging status LED – Red
18d Charging status LED – Green
19 Mulch plug
Q Scope of delivery
1 Cordless lawnmower FARM 40-Li A1
1 Battery pack FAP 40 A1
1 Rapid battery charger FLG 40 A1
1 Grass collector (pre-assembled)
1 Lower bar mounting set (pre-assembled)
1 Upper bar mounting set
1 Carrying handle for grass collector
1 Mulch plug
1 Cable clip
1 Operating instructions
7GB

Q Technical data
Cordless
lawnmower: FARM 40-Li A1
Rated voltage: 40 V
No load speed n0: 3700 min-1
Cutting width: 430 mm
Cutting heights: 25/35/45/55/65/75 mm
Grass catcher volume: 40 l
Dimensions (H x W x D): (1010 - 1190) x 475 x
(1140 - 1350) mm
Weight (incl. accessories):15.5 kg
Protection class: III /
Degree of protection: IPX1
Battery pack: FAP 40 A1
Type: Lithium ion
Rated voltage: 36 V
40 V max.
Capacity: 2.5 Ah (90 Wh)
Number of cells: 10
Rapid battery
charger:
FLG 40 A1
Input
Rated voltage: 200 – 240 V~,
50 / 60 Hz
Power consumption: 160 W
Output
Rated voltage: 36 V
Charging current: 3.6 A
Charging time: approx. 60 min
Protection class: II /
Noise emission value:
Noise measurement value determined in
accordance with EN 60335. The A-rated noise
level of the power tool is typically as follows:
Sound pressure level LpA: 81.0 dB(A)
Uncertainty KpA: 3 dB
Sound power level LWA: 94.3 dB(A)
Uncertainty KWA: 1.81 dB
Guaranteed sound power
level LWA:
96 dB(A)
(according to 2000/14/EC amended by
2005/88/EC)
WARNING!
Wear ear protection!
Vibration emission value:
Total vibration values (vector total of three
directions) determined in accordance with
EN 60335:
Hand/arm vibration ah : 2.81 m/s2
Uncertainty K: 1.5 m/s2
WARNING!
uThe vibration level varies in accordance
with the use of the power tool and may
be higher than the value specified in these
instructions in some cases. There is a risk of
underestimation of the vibration load if the
power tool is used regularly in this manner.
Try to keep the vibration loads as low as
possible. Measures to reduce the vibration
load are, e. g. wearing gloves and limiting
the working time. Wherein all states of
operation must be included (e. g. times when
the power tool is switched off and times
where the power tool is switched on but
running without load).
NOTE
uThe vibration level specified in these
instructions has been measured in
accordance with a standardised measuring
procedure specified in EN 60335 and can
be used to make equipment comparisons.
The specified vibration emission value can
also be used to make an initial exposure
estimate.
8 GB

Safety warnings
WARNING! RISK OF ELECTRIC
SHOCK!
Protect the electrical parts against
moisture. Do not immerse such parts in
water or other liquids to avoid electrical
shock. Never hold the appliance under
running water. Pay attention to the
instructions for cleaning and care.
Do not operate the appliance with wet
hands or while standing on a wet floor.
Do not touch the power plug with wet
hands.
NOTE
Appliances with this symbol are
classified as protection class II. This
means the product is equipped with
enhanced or double insulation between
the mains supply circuit and the output
voltage or the metallic casing.
Appliances with this symbol are
classified as protection class III. This
means the appliance is supplied from
a separated / safety extra-low voltage
(SELV) power source. Under normal
conditions a person can safely come into
contact with it without risk of electrical
shock.
Q Safe operating practices
for electrically powered
lawnmowers
IMPORTANT READ
CAREFULLY BEFORE USE.
KEEP FOR FUTURE
REFERENCE.
1. The product shall not be
used by children.
2. Children should be
supervised to ensure that they
do not play with the product.
3. Cleaning and user
maintenance shall not be
made by children.
4. This product can be used
by persons with reduced
physical, sensory or mental
capabilities or lack of
experience and knowledge
if they have been given
supervision or instruction
concerning use of the product
in a safe way and if they
understand the hazards
involved.
Training
1. Read the instructions
carefully. Be familiar with the
controls and the correct use
of the product.
2. Never allow children or
people unfamiliar with
these instructions to use the
product. Local regulations
can restrict the age of the
operator.
3. Never operate the product
while people, especially
children, or pets are nearby.
9GB

4. Keep in mind that the
operator or user is
responsible for accidents or
hazards occurring to other
people or their property.
Preparation
1. While operating the product
always wear substantial
footwear and long trousers.
Do not operate the product
when barefoot or wearing
open sandals. Avoid
wearing clothing that is
loose fitting or that has
hanging cords or ties.
2. Thoroughly inspect the area
where the product is to be
used and remove all objects
which can be thrown by the
product.
3. Before using, always
visually inspect to see that
the blade, blade bolt and
the blade assembly are
not worn or damaged.
Replace worn or damaged
components in sets to
preserve balance. Replace
damaged or unreadable
labels.
Operation
1. Operate the product only in
daylight or in good artificial
light.
2. Avoid operating the product
in wet grass.
3. Always be sure of your
footing on slopes.
4. Walk, never run.
5. Mow across the face of
slopes, never up and down.
6. Exercise extreme caution
when changing direction on
slopes.
7. Do not mow excessively
steep slopes.
8. Use extreme caution when
reversing or pulling the
product towards you.
9. Stop the blade(s) if the
product has to be tilted
for transportation when
crossing surfaces other
than grass, and when
transporting the product
to and from the area to be
used.
10. Never operate the product
with defective guards or
shields, or without safety
devices, for example
deflectors and/or grass
collector, in place.
10 GB

11. Switch on the motor
carefully according to
instructions and with
feet well away from the
blade(s).
12. Do not tilt the product when
switching on the motor,
except if the product has to
be tilted for starting. In this
case, do not tilt it more than
absolutely necessary and lift
only the part, which is away
from the operator.
13. Do not start the product
when standing in front of the
discharge opening.
14. Do not put hands or feet
near or under rotating parts.
Keep clear of the discharge
opening at all times.
15. Do not transport the product
while the power source is
running.
16. Stop the product, and
remove the disabling device.
Make sure that all moving
parts have come to a
complete stop:
¢whenever you leave the
product,
¢before clearing blockages
or unclogging chute,
¢before checking, cleaning or
working on the product,
¢after striking a foreign
object. Inspect the product
for damage and make
repairs before starting and
operating the product.
If the product starts to
vibrate abnormally (check
immediately):
¢inspect for damage,
¢replace or repair any
damaged parts,
¢check for and tighten any
loose parts.
Maintenance and storage
1. Keep all nuts, bolts and
screws tight to be sure the
product is in safe working
condition.
2. Check the grass collector
frequently for wear or
deterioration.
3. On products with multi
blade, take care as rotating
one blade can cause other
blades to rotate.
4. Be careful during adjustment
of the product to prevent
entrapment of the fingers
between moving blades and
fixed parts of the product.
5. Always allow the product to
cool down before storing
11GB

6. When servicing the blades
be aware that, even
though the power source is
switched off, the blades can
still be moved.
7. Replace worn or damaged
parts for safety. Use only
genuine replacement parts
and accessories.
Q Vibration and noise reduction
To reduce the impact of noise and vibration
emission, limit the time of operation, use low-
vibration and low-noise operating modes as well
as wear personal protective equipment.
Take the following points into account to minimise
the vibration and noise exposure risks:
¢Only use the product as intended by its
design and these instructions.
¢Ensure that the product is in good condition
and well maintained.
¢Use correct attachments for the product and
ensure they are in good condition.
¢Keep tight grip on the handles / grip
surfaces.
¢Maintain this product in accordance with
these instructions and keep it well lubricated
(where appropriate).
¢Plan your work schedule to spread any high
vibration tool use across a longer period of
time.
Q Behaviour in emergency
situations
Familiarise yourself with the use of this product by
means of this instruction manual. Memorise the
safety warnings and follow them to the letter. This
will help to prevent risks and hazards.
¢Always be alert when using this product, so
that you can recognise and handle risks early.
Fast intervention can prevent serious injury
and damage to property.
¢Switch the product off, remove the battery
pack and disengage the safety key if there
are malfunctions. Have the product checked
by a qualified professional and repaired, if
necessary, before you operate it again.
Q Residual risks
Even if you are operating this product in
accordance with all the safety requirements,
potential risks of injury and damage remain. The
following dangers can arise in connection with the
structure and design of this product:
¢Health defects resulting from vibration
emission if the product is being used over
long periods of time or not adequately
managed and properly maintained.
¢Injuries and damage to property due to
broken cutting attachments or the sudden
impact of hidden objects during use.
¢Danger of injury and property damage
caused by flying objects.
WARNING!
uThis product produces an electromagnetic
field during operation! This field may under
some circumstances interfere with active or
passive medical implants! To reduce the risk
of serious or fatal injury, we recommend
persons with medical implants to consult their
doctor and the medical implant manufacturer
before operating this product!
Q Battery charger safety
warnings
CAUTION! RISK OF EXPLOSION!
45
45
Never charge non-rechargeable
batteries! Protect the battery pack
against heat, e. g. against continuous
intense sunlight, fire, water and
moisture. Danger of explosion.
12 GB

¢This appliance can be
used by children aged
from 8 years and above
and persons with reduced
physical, sensory or mental
capabilities or lack of
experience and knowledge
if they have been given
supervision or instruction
concerning use of the
appliance in a safe way
and understand the hazards
involved.
¢Children shall not play with
the appliance.
¢Cleaning and user
maintenance shall not be
made by children without
supervision.
¢Do not charge non-
rechargeable batteries.
Disregarding this instruction is
hazardous.
¢If the supply cord
is damaged, it must
be replaced by the
manufacturer, its service
agent or similarly qualified
persons in order to avoid a
hazard.
¢Protect the electrical parts
against moisture. Do not
immerse such parts in water
or other liquids to avoid
electrical shock. Never hold
the appliance under running
water. Pay attention to the
instructions provided for
cleaning, maintenance and
repair.
¢The appliance is suitable for
indoor use only.
¢This charger is only designed
for charging the battery pack
type: FAP 40 A1.
Q Initial use
Q Unpacking
CAUTION! RISK OF EXPLOSION
Packaging materials are not toys.
Children should not play with the
packaging materials, as they pose a
risk of swallowing and suffocation!
Remove all packaging materials and
shipping devices.
1. Unpack all parts and lay them on a flat,
stable surface.
2. Remove all packing materials and shipping
devices if applicable.
3. Make sure the delivery contents are complete
and free of any damage. If you find that
parts are missing or show damage do not
use the product but contact your dealer. Do
not use the product unless missing parts have
been delivered in addition or defective parts
have been replaced. Using an incomplete
or damaged product represents a hazard to
people and property.
13GB

4. Ensure that you have all the accessories and
tools needed for assembly and operation.
This also includes suitable personal protective
equipment.
Q Accessories
To operate this product safely and correctly, the
following accessories, i. e. tools and attachments,
are necessary:
oSuitable personal protective equipment
Accessories and tools are available through your
authorised dealer. When buying always consider
the technical requirements of this product (see
“Technical data”).
If you are not certain, ask a qualified specialist and
get advice from your trusted dealer.
NOTE
uThis instruction manual contains information
and suggestions for several attachments and
their uses. The attachments mentioned are not
necessarily included in the shipment, but are
meant to indicate additional possibilities for
using this product.
Q Assembly
Attaching the lower bar
1. Fold up the lower bar
3to a convenient
height and engage the gears in a secure
position (see. Fig. D). Raise both lower
bars
3to the same height.
2. Turn the lever 10b clockwise to tighten the
connection, but to not fully tighten it.
3. Tilt down the lever 10b to secure the
connection. If this requires too much force or
is impossible loosen the lever 10b a little by
turning it anti-clockwise.
4. Repeat step 1 – 3 on the other side.
Attaching the upper bar
1. Align the open end of the upper bar
2with
the lower bars
3and slide it down until the
holes in both parts are congruent with each
other and hold it in place (see Fig. E).
2. Fit the bolt 13a from the product centre
outward through the holes and hold it in
place.
3. Slide the washer 13b with the flat side facing
outwards onto the bolt 13a . The recess of the
washer 13b should fit the upper bar 2.
4. Screw the lever 13c onto the bolt 13a .
5. Turn the lever 13c clockwise to tighten the
connection, but to not fully tighten it.
6. Tilt down the lever 13c to secure the
connection. If this requires too much force or
is impossible loosen the lever 13c a little by
turning it anti-clockwise.
7. Repeat step 1 – 6 on the other side.
Securing the control cable
1. Use the cable clip
12 and insert the control
cable
14 through the open end (see Fig. F).
2. Clip the cable clip
12 with the control
cable
14 onto the lower bar 3.
Q Before use
Q Charging the battery pack
NOTE
uThe battery pack 17 comes partly charged.
Charge the battery pack
17 prior to first use,
ideally at least 60 minutes.
uAlways pull out the power plug 18a of the
charger
18 from the mains before removing
or connecting the battery pack
17 to the
charger.
uNever charge the battery pack
17 when
the ambient temperature is below 10 °C or
above 40 °C.
uRest the charger
18 for at least 15 minutes
between successive charging sessions.
uIf no battery pack
17 is inserted into the
charger
18 and the charger is connected to
mains, the charging status LED 18d flashes
green.
1. Align the battery pack
17 to the rails of the
charger
18 and slide it in. Ensure it clicks
noticeably in place.
14 GB

2. Connect the power plug 18a of the
charger
18 with the mains. The charging
status LED 18c lights up red. The continuously
lit green charging status
LED 18d indicates that the charging process is
complete.
3. Disconnect the power plug 18a of the
charger
18 from the mains and remove the
battery pack
17 from the charger.
4. Attach the battery pack
17 back to the
product (see “Attaching / removing the
battery pack”).
Charging status LEDs
Green LED flashes
without battery pack Charger ready
Green LED lights up
with battery pack Battery pack fully charged
Red LED lights up with
battery pack Battery pack charging
Red and green LEDs
flashing Battery pack defect
Red and green LEDs
continuously lit Battery pack too cold or warm
Q Checking the battery charging
level
oPress the battery level button 17c to check the
charging level of the battery pack
17 . The
charging level will be shown on the battery
level indication lights 17b .
4 Green LEDs
continuously lit 100% battery charging level
3 Green LEDs
continuously lit 75% battery charging level
2 Green LEDs
continuously lit 50% battery charging level
1 Green LED
continuously lit 25% battery charging level
1 Green LED flashing Low battery charging level
oCharge the battery pack
17 before operation
when it is at 25% or low battery charging
level.
Q Safety key
This product is equipped with a safety key 7c to
prevent unauthorised use. In order to operate the
product the safety key 7c must be engaged in the
safety keyhole 7b .
Engaging the safety key
1. Open the battery compartment cover
7
(see Fig. G).
2. Press the button on the safety key 7c and
slide it into the safety keyhole 7b . Ensure
it clicks noticeably in place. It shall not be
possible to remove the safety key 7c
without pressing its button.
Disengaging the safety key
1. Press the button on the safety key 7c and
pull it out of the safety keyhole 7b .
Q Attaching / removing the
battery pack
Attaching the battery pack:
1. Open the battery compartment cover
7
(see Fig. G).
2. Align the battery pack
17 to the rails of the
battery pack bay and slide it into it. Ensure it
clicks noticeably in place.
Removing the battery pack:
1. Open the battery compartment cover
7
(see Fig. G).
2. Press the release button 17a and slide out the
battery pack
17 from the battery pack bay.
Q Operation
Q Grass collector
This product can be used with a grass collector
11
that holds the cut grass for easy disposal. If not
used, the cut grass will be ejected through the rear
discharge opening.
To clear the rear discharge opening the mulch
plug
19 must be removed.
1. Lift the discharge cover
4with one hand
and remove the mulch plug
19 .
15GB

Attaching carrying handle on grass
collector
1. Attach front end of the carrying handle 11a
to the slot of the grass collector 11 (see Fig. H).
2. The hook at the front end of carrying
handle 11a should snap fit into the cover of
the grass collector 11 . Attach the rear end to
the carrying handle 11a to the end slot of the
grass collector 11 .
3. Apply small pressure to the carrying
handle 11a until the hook at the rear end of
the carrying handle snap fit into the cover of
the grass collector 11 .
NOTE
uFabric handle is available at the back of
grass collector 11 .
Attaching the grass collector
1. Lift the discharge cover
4with one hand
and hold it in position (see Fig. I).
2. Hold the grass collector
11 with the other
hand by its carrying handle 11a and
hang it with its supports into the hooks on the
housing
9.
3. Release the discharge cover
4.
Removing the grass collector
1. Lift the discharge cover
4with one hand
and hold it in position (see Fig. I).
2. Hold the grass collector
11 with the other
hand by its carrying handle 11a and lift it
from the hooks on the housing
9.
3. Release the discharge cover
4.
Emptying the grass collector
Observe the fill indicator flap 11b on top of the
grass collector
11 during operation. The flap
should open up by the air flow through the grass
collector
11 with available capacity. A closed flap
indicates a full grass collector
11 and it must be
emptied before continuing operation.
1. Remove the grass collector
11 (see
“Removing the grass collector”).
2. Dispose of the cut grass through the open
side of the grass collector
11 according to
local regulations.
Q Mulch plug
This product can be used for mulching grass with
the mulch plug
19 . The mulch plug will block the
rear discharge opening. The cut grass is chopped
several times to produce tiny bits of grass. The
cuttings will be left on the lawn where they will
soon rot down and perform fertilizing function.
Attaching the mulch plug
1. Lift the discharge cover
4with one hand
and attach the mulch plug
19 .
Removing the mulch plug
1. Lift the discharge cover
4with one hand
and remove the mulch plug
19 .
Q Adjusting the cutting height
This product has 6 settings to adjust to one of the
below cutting heights.
Setting Cutting height
(ca.) in mm
75
65
55
45
35
25
1. Disengage the height adjustment lever
6
by pushing it sideways out of the notch for the
current setting (see Fig. J).
2. Move the height adjustment lever
6back or
forth towards the notch for the desired cutting
height.
3. Engage the height adjustment lever
6by
pushing it sideways into the notch of the
desired cutting height.
16 GB

Q Switching on and off
Switching on:
1. Operate the lock-off button
15 and hold it in
position (see Fig. K).
2. Pull the on / off switch
16 towards the
handle
1to switch on. Release the lock-off
button
15 .
Switching off:
1. Release the on / off switch
16 to switch off.
Q Mowing
WARNING! RISK OF INJURY!
uIf the product strikes a foreign object stop
the motor! Switch the product off, remove
the battery pack, disengage the safety key
and let it cool down. Inspect the product
thoroughly for damage! Have any damage
repaired before restarting!
uExtensive vibration of the product during
operation is an indication of damage! Stop
the motor. The product should be promptly
inspected and repaired!
WARNING!
uIn some countries regulations define at
what time of the day and on what special
days products are allowed to be used and
what restrictions apply! Ask your community
for detailed information and observe the
regulations in order to preserve a peaceful
neighbourhood and avoid committing
administrative offences!
oMake sure that the lawn is clear of stones,
sticks, wire or other objects that could
damage the product or its motor.
oDo not cut wet grass because it tends to stick
to the underbody of the product, preventing
the proper discharge of grass clippings, and it
could also cause you to slip and fall.
oNever cut off more than one-third of the total
length of the grass for a healthy lawn. In the
autumn, lawns should only be cut as long as
there is growth.
oSlowly push the product forward.
oMow in slightly overlapping rows. The most
effective pattern for mowing lawns is straight
lines along one of the sides. This will keep the
rows even and ensures that all the lawn is cut
without missing any spots.
oCircle around flower beds. When reaching
a flower bed in the middle of the lawn, cut a
row or two around the circumference of the
bed.
oPay special attention when changing
direction.
oEmpty the grass collector
11 regularly.
oSwitch the product off immediately if you
are disturbed while working by other people
entering the working area. Always let the
product come to complete stop before
averting.
oDo not overwork yourself. Take regular breaks
to ensure you can concentrate on the work
and have full control over the product.
Q After use
1. Switch the product off, remove the battery
pack
17 , disengage the safety key 7c and
let it cool down.
2. Check, clean and store the product (see
“Cleaning and care”).
Q Cleaning and care
WARNING!
Always switch the product off, remove
the battery pack and let the product
cool down before performing inspection,
maintenance and cleaning work!
CAUTION! RISK OF INJURY!
The blade(s) are sharp! Always wear
protective gloves when performing
inspection, maintenance and cleaning
work!
17GB

Q Cleaning
oThe product must always be kept clean, dry
and free from oil or grease. Remove debris
from it after each use and before storage.
oRegular and proper cleaning will help ensure
safe use and prolong the life of the product.
oInspect the product before each use for worn
and damaged parts. Do not operate it if you
find broken and worn parts.
oNever allow fluids to get into the product.
oClean the product with a dry cloth. Use a
brush for areas that are hard to reach.
NOTE
uDo not use chemical, alkaline, abrasive or
other aggressive detergents or disinfectants to
clean this product as they might be harmful to
its surfaces.
Q Maintenance
Before and after each use, check the product
and accessories (or attachments) for wear and
damage. If required, exchange them for new ones
as described in this instruction manual. Observe
the technical requirements (see “Technical data”).
Q Repair
This product does not contain any parts that can
be repaired by the user. Contact an authorised
service centre or a similarly qualified person to
have it checked and repaired.
Q Storage
oSwitch the product off, remove the battery
pack
17 and disengage the safety key 7c .
oClean the product as described (see
“Cleaning”).
oStore the product and its accessories in a
dark, dry, frost-free, well-ventilated place.
oAlways store the product in a place that is
inaccessible to children. The ideal storage
temperature is between 10 °C and 30 °C.
oWe recommend covering the product with a
suitable cloth or enclosure to protect it against
dust.
oRegularly check the charge level of the
battery pack, if it is to be stored for an
extended period. Optimum storage conditions
are cool and dry. Optimal state of charge for
storage is approximately 50%.
Q Transportation
CAUTION! RISK OF INJURY!
Lift with two persons.
oSwitch the product off and, remove the
battery pack
17 and disengage the safety
key 7c .
oAttach shipping devices, if applicable.
oWhen lifting is unavoidable, lift with two
people. The product should only be lifted by
the carrying handle 5and front end of the
product. Wear safety gloves when carrying
the product to prevent accidental contact of
the blade.
oAlways push the product by its handle.
oProtect the product from any heavy impact
or strong vibrations which may occur during
transportation in vehicles.
oSecure the product to prevent it from slipping
or falling over.
Q Troubleshooting
WARNING!
uOnly perform the steps described within
these instructions! All further inspection,
maintenance and repair work must be
performed by an authorised service centre or
a similarly qualified specialist if you cannot
solve the problem yourself!
Suspected malfunctions are often due to causes
that the users can fix themselves. Therefore check
the product using this section. In most cases the
problem can be solved quickly.
18 GB

Problem Possible cause Solution
Product
does not
start
Battery pack not
properly attached Attach properly
Battery pack
discharged Remove and charge the battery pack
Battery pack
damaged Check by a specialist electrician
Safety key
disengaged Engage safety key
Other electrical
defect to the product Check by a specialist electrician
Clogging Stop the product,
remove the battery
pack and disengage
the safety key. Check
underneath the
product and clear
out as necessary
(always wear
protective gloves).
Product
does not
reach full
power
Battery pack
capacity too low Remove and charge the battery pack
Unsatisfac-
tory result Cutting device is dull / damaged Have it replaced with a new one by an
authorised service
centre
Cutting material
exceeds capacity Only cut materials according to capacity
of the product
Cutting height is
incorrect Adjust cutting height
Product
suddenly
stops
Product overloaded Adjust cutting height
Battery pack
discharged Remove and charge the battery pack
Battery pack too hot Remove the battery
pack and let it cool
down
Excessive
vibration
or noise
Cutting device is
dull / damaged Have it replaced with a new one
Bolts / nuts are loose Tighten bolts / nuts
Q Disposal
The packaging is made entirely of recyclable
materials, which you may dispose of at local
recycling facilities.
Observe the marking of the packaging
materials for waste separation, which
are marked with abbreviations (a) and
numbers (b) with following meaning: 1 - 7:
plastics / 20 - 22: paper and fibreboard /
80 - 98: composite materials
The product and packaging materials are
recyclable, dispose of it separately for
better waste treatment.
The Triman logo is valid in France only.
Contact your local refuse disposal
authority for more details of how to
dispose of your worn-out product.
To help protect the environment, please
dispose of the product properly when it
has reached the end of its useful life and
not in the household waste. Information on
collection points and their opening hours
can be obtained from your local authority.
Faulty or used batteries / rechargeable
batteries must be recycled in accordance
with Directive 2006/66/EC and its
amendments. Please return the batteries /
rechargeable batteries and / or the
product to the available collection points.
Environmental damage through
incorrect disposal of the batteries /
rechargeable batteries!
Remove the batteries / battery pack
from the product before disposal.
Batteries /rechargeable batteries may not
be disposed of with the usual domestic
waste. They may contain toxic heavy
metals and are subject to hazardous
waste treatment rules and regulations. The
chemical symbols for heavy metals are as
follows:
Cd = cadmium, Hg = mercury, Pb = lead.
That is why you should dispose of used
batteries / rechargeable batteries at a
local collection point.
19GB

Q Service
WARNING!
uHave your product repaired at the service
centre or an electrician, using only original
manufacturer parts. This will maintain the
safety of this product.
uAlways have a plug or power cord of
the charger replaced by the product
manufacturer or its service centre. This will
maintain the safety of this product.
Q Warranty
The product has been manufactured to strict
quality guidelines and meticulously examined
before delivery. In the event of product defects
you have legal rights against the retailer of this
product. Your legal rights are not limited in any
way by our warranty detailed below.
The warranty for this product is 3 years from the
date of purchase. Should this product show any
fault in materials or manufacture within 3 years
from the date of purchase, we will repair or
replace it – at our choice – free of charge to you.
The warranty period begins on the date of
purchase. Please keep the original sales receipt
in a safe location. This document is required as
your proof of purchase. This warranty becomes
void if the product has been damaged, or used or
maintained improperly.
The warranty applies to defects in material
or manufacture. This warranty does not cover
product parts subject to normal wear, thus
possibly considered consumables (e.g. batteries)
or for damage to fragile parts, e.g. switches,
rechargeable batteries or glass parts.
The warranty for this rechargeable battery pack is
1 year from the date of purchase.
Warranty claim procedure
To ensure quick processing of your case, please
observe the following instructions:
Please have the till receipt and the item number
(e.g. IAN 123456) available as proof of
purchase. You will find the item number on the
type plate, an engraving on the front page of the
instructions (bottom left), or as a sticker on the rear
or bottom of the product.
If functional or other defects occur, please contact
the service department listed either by telephone
or by e-mail.
You can return a defective product to us free of
charge to the service address that will be provided
to you. Ensure that you enclose the proof of
purchase (till receipt) and information about what
the defect is and when it occurred.
Service Great Britain
Tel.: [phone] (£ 0.10/Min.)
E-Mail: [email protected]
IAN 292278
20 GB

Q Translation of original
declaration of conformity
We, OWIM GmbH & Co. KG, Stiftsbergstraße1,
DE-74167 Neckarsulm, GERMANY, hereby
declare under our sole responsibility that the
product: cordless lawnmower FARM 40-Li A1,
model no.: HG03586, version: 02/2018, to
which this declaration refers, complies with the
standards / normative documents of 2006/42/
EC, 2014/35/EU, 2014/30/EU, 2011/65/EU,
2000/14/EC, 2005/88/EC.
Applied harmonised standards:
EN 60335-1: 2012/A11: 2014
EN 60335-2-77: 2010
EN 60335-2-29: 2004+A2: 2010
EN 62233: 2008
EN 55014-1: 2006/A2: 2011
EN 55014-2: 2015
EN 61000-3-2: 2014
EN 61000-3-3: 2013
EN 50581: 2012
We additionally confirm the following in
accordance with the 2000/14/EC emissions
guideline:
Sound power level
guaranteed: 96 dB(A)
measured: 94,3 dB(A)
Compliance evaluation process carried out in
accordance with Annex VI, 2000/14/EC
Name of notified body:
TÜV SÜD Industrie Service GmbH (Notified body:
0036)
Address of notified body:
Westendstraße 199, 80686 München, Germany
Serial number: IAN 292278
Tobias König
Division Manager / Responsible for
documentation
OWIM GmbH & Co. KG, Stiftsbergstraße 1,
DE-74167 Neckarsulm, GERMANY
Neckarsulm, 16.01.2018
The declaration of conformity can also be viewed
at: www.owim.com.
The object of the declaration described above
satisfies the provisions of Directive 2011/65/EU
of the European Parliament and the Council of
8 June 2011 on limiting the use of certain harmful
substances in electrical and electronic appliances.
21GB

Tartalomjegyzék
Az alkalmazott piktogramok magyarázata........................................................... Oldal 23
Bevezető ................................................................................................................................. Oldal 24
Rendeltetésszerű alkalmazás .................................................................................................... Oldal 24
A készülék részei ....................................................................................................................... Oldal 24
Szállítási terjedelem .................................................................................................................. Oldal 24
Műszaki adatok ........................................................................................................................ Oldal 25
Biztonsági figyelmeztetések ......................................................................................... Oldal 26
Adatok az elektromos hajtású fűnyíró biztonságos használatához .......................................... Oldal 26
Vibráció- és zajcsökkentés ........................................................................................................ Oldal 30
Viselkedés vészhelyzetben ........................................................................................................ Oldal 30
Maradék kockázatok ................................................................................................................ Oldal 30
Biztonsági utasítások a töltőkészülékekhez ............................................................................... Oldal 30
Az első használat előtt .................................................................................................... Oldal 32
Kicsomagolás ........................................................................................................................... Oldal 32
Tartozékok ................................................................................................................................. Oldal 32
Összeszerelés ........................................................................................................................... Oldal 32
A használat előtt ................................................................................................................ Oldal 33
Az akkumulátor töltése .............................................................................................................. Oldal 33
Akkumulátor töltési állapot ellenőrzése ..................................................................................... Oldal 33
Biztonsági kulcs ......................................................................................................................... Oldal 34
Az akkumulátor berakása/kivétele ........................................................................................... Oldal 34
Kezelés .................................................................................................................................... Oldal 34
Fűgyűjtő .................................................................................................................................... Oldal 34
Mulcsozó dugó ......................................................................................................................... Oldal 35
A vágási magasság beállítása .................................................................................................. Oldal 35
Be- és kikapcsolás ..................................................................................................................... Oldal 35
Fűnyírás ..................................................................................................................................... Oldal 35
A használat után ....................................................................................................................... Oldal 36
Tisztítás és ápolás .............................................................................................................. Oldal 36
Tisztítás ...................................................................................................................................... Oldal 36
Karbantartás ............................................................................................................................. Oldal 37
Javítás ....................................................................................................................................... Oldal 37
Tárolás ...................................................................................................................................... Oldal 37
Szállítás ..................................................................................................................................... Oldal 37
Üzemzavarok és elhárításuk ........................................................................................ Oldal 37
Ártalmatlanítás.................................................................................................................... Oldal 38
Szerviz ..................................................................................................................................... Oldal 39
Garancia ................................................................................................................................. Oldal 39
Az eredeti megfelelőségi nyilatkozat fordítása.................................................... Oldal 40
22 HU