Floyd Shelving System User manual

Shelving
System

Components
The Tall Shelf
The Short Shelf
The Wardrobe
The Display Shelf
Installing the Wall Anchor
+ Adding a Tall Shelf?
+ Adding a Short Shelf?
+ Adding a Wardrobe?
+ Adding a Display Shelf?
04
16
36
54
76
100
112
114
116
118
Table of
Contents

Components
Wood Supports
a. Tall / Wardrobe / Display
b. Short
4×b.a.
Fixed Shelves
2×1×2×2×
Tall Short Display Wardrobe

Components cont.
Hex Tool
Felt Pads
(for bottom of wood supports)
1×
8×
Shelves
4×2×3×1×
Tall Short Display Wardrobe
Nuts
Bolts
16×
16×
8×
8×
16×
16×
16×
16×
Tall Short Display Wardrobe

Components cont.
Wardrobe Brackets
Wardrobe Bar
2×
1×
WARDROBE ONLY
Display Shelf1×
DISPLAY SHELF ONLY

Wall Anchor
Kit Components
Wall Anchor Bracket
Screws
Velcro Tape Strap
Drywall Anchors
1×
2×
1×
2×

Additional items
you may need
for installing the
Wall Anchor:
Phillips Head Screwdriver
Hammer
Drill w/ 1/4” Drill Bit
1×
1×
1×

Assembly Tips:
– Keep all packaging until assembly is complete to
ensure you have all parts needed for assembly.
– Assemble on a soft surface, like a rug or
cardboard to protect the finish.
– Two people are recommended for assembly.
– If your floor is uneven, you can use the provided
felt pads to level your Shelving System. The
felt pads can be stacked on top of each other to
add more height on one or more Wood Supports
as needed.
– WARNING: Serious or fatal crushing injuries can
occur from furniture tip-over. The Wall Anchor Kit
should be installed to help prevent tip-over for
the Tall Shelf, Wardrobe, and Display Shelf.

The Tall
Shelf
Shelf
System
16

1Place one fixed shelf (a)
with its back edge on the
floor and have a friend hold
in place. Place two wood
supports on either side
of the fixed loop with the
metal part facing down.
The bottom end of the wood
supports have a notch cut in
the wood. Align the holes at
the bottom end of the wood
supports with the square
holes on the fixed shelves.
Position
the
first fixed
shelf
a
a

2a
Insert two bolts through
the square holes in the
fixed shelf (a) and until
they are fully inserted.
Next, insert the nuts (b)
through the holes in the
wood and begin to tighten
them to the bolts by hand.
Begin to
attach the
first fixed
shelf
a
b

2b
Finish tightening the nuts
with the hex tool. The bolt
should stay in place, but may
need to be pressed to hold in
place when tightening the nut.
Repeat steps 2a–2b to
tighten the fasteners on the
other side before proceeding.
Tighten
fasteners
to secure
the fixed
shelf to
the wood
supports
a
b

3
Place the fixed shelf (b) at
the top of the wood supports
and repeat steps 2a–2b to
attach it to the two wood
supports.
Attach
second
fixed
shelf at
the top
b

4
Take the two remaining
wood supports and attach
them to the fixed shelf as
shown in steps 2a–2b. Have
a friend hold the wood supports
in place while you attach them
to the fixed shelves.
Attach
the front
wood
supports

5
Stand the shelf upright
with the help of a friend.
Note: After standing up
the shelf, double check each
connection to make sure
fasteners are fully tightened
and secure.
Stand the
Shelf up-
right

6
To attach the shelves, insert each
shelf from the back at a 45 degree
angle. Rotate the shelf parallel to the
floor so that the tall side flanges of
the shelf are in between the wood
supports. Insert the hooks on each
shelf into the slots in the metal tracks
on the back side of each wood support.
Note: Make sure all four hooks on each
shelf are inserted into the slots in the
metal tracks on the wood supports.
Add the
shelves

7The shelf spacing is adjustable.
With each shelf attached to the
middle slot, the shelves will be
evenly spaced. To increase or
decrease shelf spacing, insert
the hooks on the shelves into
the slots above or below the
middle slots.
Adjust
the
shelves
(optional)

8
After adding the shelves and
adjusting them as desired,
place the fully assembled
shelf unit against the wall.
Now that the assembly is
complete, flip ahead to page
100 to install the Wall Anchor
and attach your Shelving
System to the wall. The Wall
Anchor Kit should be installed
to help prevent furniture
tip-over.
@floyddetroit
#thefloydshelf
Install
the wall
anchor

The Short
Shelf
Shelf
System
36

1Place the fixed shelf with
its back edge on the floor
and have a friend hold in
place. Place two wood
supports on either side
of the fixed loop with the
metal part facing down.
The bottom end of the wood
supports have a notch cut in
the wood. Align the holes at
the bottom end of the wood
support with the square
holes on the fixed shelves.
Position
the fixed
shelf
a
a