Floyd Dresser System User manual

The Dresser System (Two Unit)
How to Assemble:

Assembly Instructions The Dresser System
14x Bolts
Components 2x Units
8x Wing Nuts
2x Base Aprons 1x Base Leg Set
1x Top
Pro Tip: If you’re considering a return, save your packaging!

Assembly Instructions The Dresser System
1x Anti-Tip Kit
2x U-Brackets 1x Hex Tool
Components
Pro Tip: If you’re considering a return, save your packaging!

Assembly Instructions The Dresser SystemAssembling the Base
Step: 1

Assembly Instructions The Dresser System
Begin by placing the Base Aprons
and Leg Sets on a soft surface.
Guide the threaded studs on the
Base Aprons through the holes in
the end of each Leg Set.
Use the 8 provided Base Wing
Nuts to secure the Base Aprons to
the Leg Sets, making sure to fully
tighten all Bolts.
01. 02.
Step: 1A

Assembly Instructions The Dresser System
Once assembled, place the Base on
a level surface near its final location.
Step: 1B

Assembly Instructions The Dresser SystemAdding the Units
Step: 2

Assembly Instructions The Dresser System
With a partner, begin by placing
the first Module onto the side of
your choice.
Both blocks on the underside of the
Module should fit within the frame
of the Base.
Step: 2A

Assembly Instructions The Dresser System
Ensure that the blocks located
on the underside of the Module
are aligned squarely between
the Base Aprons.
Slide the Module back and to
the left until it stops.
01. 02.
Step: 2B

Assembly Instructions The Dresser System
With the first Module now in place,
insert 4 Bolts through the openings
in the Base Aprons as shown.
Loosely tighten each by hand.
Step: 2C

Assembly Instructions The Dresser System
Repeat Steps 2A-C to install
the second Unit.
After both Units are in place, use
the Hex Tool to tighten all Bolts.
01.
02.
Step: 2D

Assembly Instructions The Dresser System
Once the Units are in place and
aligned, slide 2 U-Brackets into the
slots at top of each Unit.
Push both Brackets down firmly to
secure the Units to one another.
Step: 2EStep: 2E

Assembly Instructions The Dresser System
Place the Top onto the The Dresser.
Ensure the angled metal cleat on its
underside fits between the opening
at top of the Units.
Step: 2F

Assembly Instructions The Dresser System
With the angled metal cleat between
the opening in the top of the Unit,
push the Top back.
The cleat should lock into place with
corresponding cleat on top of the Unit.
01. 02. 03.
Step: 2G

Assembly Instructions The Dresser System
Step: 2H
Ensure all the components are square
and aligned.
Then, insert Bolts through the marked
holes in the underside of the Units’
tops and into corresponding holes in
the underside of the Top.
Tighten with the Hex Tool.
NOTE: For Units with drawers, open top drawer to insert Bolts.

Assembly Instructions The Dresser System
Install the Anti-Tip Kit.
Use a set of holes closest to the
center on the back of the unit to
attach the Anti-Tip Kit.
Follow the instructions included with
the Anti-Tip Kit to install. Always
install and use the Anti-Tip Kit.
Once Unit is in place and secured
to wall follow next steps to attach
drawer faces or doors.
WARNING: Serious or fatal crushing injuries can occur from furniture tip-over. Always install tip-over restraint provided to help reduce risk of tip-over.
Step: 2I

Assembly Instructions The Dresser SystemFinishing the Units
Step: 3

Assembly Instructions The Dresser System
12x Screws
Components
2 Large Drawer Unit
2 Medium Drawer Unit
2 Mixed Drawer Unit
2x Drawer Faces
3x Drawer Faces
3x Drawer Faces
12x Screws
NOTE: To assemble these components, you’ll need a #2 Phillips-Head Screwdriver (not provided).
Drawer Units
8x Screws

Assembly Instructions The Dresser System
Start by opening the top Drawer.
Align Drawer Face and attach it
to the Module from the inside of
the Drawer, using 4 of the provide
Screws and a #2 Phillips-Head
Screwdriver.
Once all 4 Screws are in place,
tighten each. Then, one at a time,
repeat these steps with the
remaining Drawers.
01.
Drawer Units
NOTE: For this step, you’ll need a #2 Phillips-Head Screwdriver (not provided).
02.
A
B

Assembly Instructions The Dresser System
NOTE: To assemble the 2 Door Unit, you’ll need a #2 Phillips-Head Screwdriver (not provided).
Shelf Units
Components
Open Shelf Unit
2 Door Unit
1x Shelf
1x Shelf
2x Doors
4x Shelf Pins
8x Screws
4x Shelf Pins