Floyd Dresser System User manual

The Dresser System (Two Unit)
How to Assemble:

Assembly Instructions The Dresser System
2x Units
2x Base Apron
14x Bolts
2x Base Leg Set
4x Base Wing Nuts
1x Top
Components
Pro Tip: If you’re considering a return, save your packaging!

Assembly Instructions The Dresser System
2x U-Brackets 1x Hex Tool
Components
Pro Tip: If you’re considering a return, save your packaging!
1x Anti-Tip Kit
(Not Pictured)

Assembling the Base
Step: 1

Assembly Instructions The Dresser System
Step: 1A
Begin by placing the Base Aprons
and Leg Sets on a soft surface.
Guide the threaded studs on the
Base Aprons through the holes in
the end of each Leg Set.
Use the 4 provided Base Wing Nuts
to secure the Base Aprons to the
Leg Sets.

Assembly Instructions The Dresser System
Once assembled, place the Base on
a level surface near its final location.
Step: 1B

Adding the Units
Step: 2

Assembly Instructions The Dresser System
With a partner, begin by placing the first
Module onto the side of your choice.
Both blocks on the underside of the
Module should fit within the frame of
the Base.
Step: 2A

Assembly Instructions The Dresser System
Ensure that the blocks located on the
underside of the Module are aligned
squarely between the Aprons.
Slide the Module back until it stops.
Step: 2B

Assembly Instructions The Dresser System
With the Module now in place, insert
4 Bolts through the openings in the
Base Aprons as shown.
Loosely tighten each by hand.
Step: 2C
Underside Detail

Assembly Instructions The Dresser System
Repeat with Steps 2A-C to install
the second Unit.
Using the Hex Tool, tighten all Bolts.
Step: 2D

Assembly Instructions The Dresser System
Once Units are in place and aligned,
slide the 2 U-Brackets into the slots
at top of Units.
Push both brackets down firmly to install.
Step: 2E

Assembly Instructions The Dresser System
Place the Top onto the The Dresser.
Ensure the angled metal cleat on its
underside fits between the opening at
top of the Units.
Step: 2F

Assembly Instructions The Dresser System
With the angled metal cleat between the
opening in the Unit— push the Top back.
The cleat should lock into place with
corresponding cleat on top of the Unit.
Step: 2G

Assembly Instructions The Dresser System
Ensure components are square and aligned.
Then, insert Bolts through the marked
holes in the Units and into the Top and
tighten with the Hex Tool.
Step: 2H
NOTE: For Units with drawers, open top drawer to insert Bolts

Assembly Instructions The Dresser System
Install the Anti-Tip Kit.
Use a set of holes closest to the
center on the back of the unit to
attach the Anti-Tip Kit.
Follow the instructions included with
the Anti-Tip Kit to install. Always
install and use the Anti-Tip Kit.
Once Unit is in place and secured
to wall follow next steps to attach
drawer faces or doors.
Step: 2I

Finishing the Units
Step: 3

Assembly Instructions The Dresser System
Components
Drawer Units
2 Large Drawer 2x Drawer Faces
3 Medium Drawer 3x Drawer Faces
3 Mixed Drawer 3x Drawer Faces

Assembly Instructions The Dresser System
Drawer Units
02.
Open the top Drawer.
Align Drawer Face and use 4 provided
Screws to attach it to the Module
from the inside of the Drawer.
After all 4 screws are in place,
tighten with a #2 screwdriver.
One at a time, repeat these steps
with the lower Drawers.
01.

Assembly Instructions The Dresser System
Components
Shelf Units
Open Shelf Unit 1x Shelf 4x Shelf Pins
2 Door Unit 1x Shelf 4x Shelf Pins
2x Doors 4x Hinges