Flying Industry Development S1X2-DC User manual

SHENZHENGUIYUANINDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: [e-mail]
RF Wireless Remote Control Radio Controller / Transmitter & Receiver
Package Include:
1 x Receiver: S1X2-DC (1 Channel / Four control Modes)
1 x Transmitter: C-2
1 x User manual
Feature:
Wireless control, easy to install
Direct power output; control Lights, Motors, Fans, electrically operated Doors/Locks/Windows/Blinds/Cars or OtherAppliances.
You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass
throughwalls,floors and doors.
With characteristics of reverse power protection andover current protection
Audible / visual indication
Use an 8-bit microcontroller w ith low-power and high-speed CMOS technology.
Reliable control: The transmitter (Encoding) and the receiver (Decoding) use an 8-bitcode.
One/ several transmitters can control one/several receivers simultaneously.
If you use two or more receivers in thesame place, youcanset themwith differentcodes.
It is recommended to use the loadwithin 3A or 50W
Receiver:
Model No.: S1X2-DC
Channel: 1 CH
Power Supply (Operating Voltage): DC 6~36V
Output: DC 6~36V
Working Frequency: 315MHz / 433MHz
Control Modes: Momentary, Latched,Toggle, 10seconds delay
Coding Type: Fixed code or learning code
Coding Setting: By learning
PCB Size: 27mmx 16mmx 7mm
Static Current: ≤6mA
MaximumWorking Current: 3A or 50W
Workwith Fixedcode transmitters or Learning code transmitters.
Transmitter:
Model No.: C-2
Channel: 2 CH
Remote Control Distance: 50m/ 150ft (theoretically)
Encode: Fixed code by Soldering
Unit size: 58mmx 39mmx 16mm
Power Supply: 1x 23A -12V battery (included,can be usedfor 12 months)
Usage:
Setting differentcontrol modes (We haveset the receiver as Latched mode before delivery. If youwant to use other modes, doas following):
1) Setting control mode Momentary: connect terminal 3 and 4.
Press and hold buttonA: output DC pow er.
Release buttonA: stop to output.
2) Setting control mode Latched: connect terminal 1 and 2.
Press buttonA: output DCpower.
Press button B:stop to output.
3) Setting control mode Toggle: Do not connect
Press buttonA: output DCpower.
Press buttonA again: stop to output.
4) Setting control mode of 10seconds delay:connectterminal 1 and 2, and connect terminal 3 and 4.
Press buttonA: output DCpower.
After 10 seconds delay,stop tooutput.
Delete alltransmitters:
We have learned remote control to the receiver. If you don’t want the receiver to work with the remote control, you can delete all codes of remote
controls,whicharestored in thereceiver.
Operation: connectsetting terminals until LED on then off; that means allstored codes have beendeleted successfully.
Learning the button of remote control:

SHENZHENGUIYUANINDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: [e-mail]
1) Connect setting terminals until LED flashes slowly; disconnect setting terminals, the receiver enters into status of LEARNING.
2) Press and hold button 1 onremote control, LEDflash once,release button 1; then press and hold button 2 on remote control, LEDflash once
again; finally, press any onebutton onremote control. If LED off, it means learning is successful.
3) The receiver can learn 12 buttons with differentcodes.
DC6V ~36V
Application Circuit
DC Lamp
OUT-
OUT+
LED
Antenna
Setting
Terminals
Work mode terminals
1
2
Input
+
_
Power supply
4
3
VCC
GND