Flying Industry Development S2PX-DC09-ANT2 User manual

SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: [e-mail]
RF Wireless Remote Control Radio Controller / Transmitter & Receiver
Package Include:
1 x Receiver: S2PX-DC09-ANT2 / S2PX-DC12-ANT2 / S2PX-DC24-ANT2 (2 Channel / Four Control Mode)
1 x Transmitter: CB-2L
1 x User manual
Feature:
Wireless control, easy to install
With high power of 30A
Direct dc power output; control Lights, Motors, Fans, electrically operated Doors / Locks / Windows / Blinds / Cars or OtherAppliances.
You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass
through walls, floors and doors.
With characteristics of reverse power protection and over current protection
Audible / visual indication
Use microcontroller model of EM78P156, an 8-bit microprocessor designed and developed with low-power and high-speed CMOS technology.
More reliable than fixed code; the transmitter use EV1527 Learning code, which is up to 1 million codes, reducing code collision and unauthorized
code scanning possibilities.
One/several transmitters can control one/several receivers simultaneously.
Two or more transmitter & receivers set can be used in the same place.
Transmitting Frequency: 315MHz / 433MHz
Working distance of transmitter and receiver with external extend antenna: 2000M / 6000ft (theoretically)
Receiver:
Model No.: S2PX-DC09-ANT2 / S2PX-DC12-ANT2 / S2PX-DC24-ANT2
Channel: 2 CH
Control Modes: Toggle, Momentary, Latched, Momentary + Toggle
Coding Type: Fixed code or learning code
Coding Setting: By learning
Power Supply (Operating Voltage): DC12V±1V (S2PX-DC12-ANT2), DC9V±1V (S2PX-DC09-ANT2), DC24V±1V (S2PX-DC24-ANT2)
Output: DC12V (S2PX-DC12-ANT2), DC9V (S2PX-DC09-ANT2), DC24V (S2PX-DC24-ANT2)
PCB Size: 137mm x 80mm x 25mm
Case Size: 150mm x 90mm x 45mm
Static Current: ≤6mA
Maximum Working Current: 30A / each channel
External Extend Antenna:
Frequency Range: 300~450MHz
Impedance: 50Ω
Antenna Length: 15cm
Cable Length: 150cm
Weight: 35g
Anti-interference, waterproof, shielded wire set inside
Magnetic stand design for easy to install
Transmitter:
Model No.: CB-2L
Channel: 2 CH
Remote Control Distance: 1000m / 3000ft (theoretically)
Encode: EV1527 Learning code (up to 1 million codes, reducing code collision and unauthorized code scanning possibilities.)
Unit size: 135mm x 42mm x 25mm
Power Supply: 1 x 6F22-9V battery (included, can be used for 12 months)
Usage:
Setting different control modes (We have set the receiver as Toggle control mode before delivery. If you want to use other control modes, do as
following):
1) Setting control mode Toggle: Only connect Jumper-2.
Press big button: Turn on the relay 1, terminal OUTPUT 1 outputs DC power.
Press big button again: Turn off the relay 1, terminal OUTPUT 1 no output.
Press small button: Turn on the relay 2, terminal OUTPUT 2 outputs DC power.
Press small button again: Turn off the relay 2, terminal OUTPUT 2 no output.
2) Setting control mode Momentary: Only connect Jumper-1.
Press and hold big button: Turn on the relay 1, terminal OUTPUT 1 outputs DC power.
Release big button: Turn off the relay 1, terminal OUTPUT 1 no output.
Press and hold small button: Turn on the relay 2, terminal OUTPUT 2 outputs DC power.
Release small button: Turn off the relay 2, terminal OUTPUT 2 no output.

SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: [e-mail]
3) Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.
Press big button: Turn on the relay 1, terminal OUTPUT 1 outputs DC power.
Turn off the relay 2, terminal OUTPUT 2 no output.
Press small button: Turn on the relay 2, terminal OUTPUT 2 outputs DC power.
Turn off the relay 1, terminal OUTPUT 1 no output.
4) Setting control mode Momentary + Toggle: Connect Jumper-1 and Jumper-2.
Control mode Momentary (Channel 1):
Press and hold big button: Turn on the relay 1, terminal OUTPUT 1 outputs DC power.
Release big button: Turn off the relay 1, terminal OUTPUT 1 no output.
Control mode Toggle (Channel 2):
Press small button: Turn on the relay 2, terminal OUTPUT 2 outputs DC power.
Press small button again: Turn off the relay 2, terminal OUTPUT 2 no output.
We have learned remote control to the receiver. If you don’t want the receiver to work with the remote control, you can delete all codes of remote
controls, which are stored in the receiver.
Operation: Press and hold the button of receiver until signal LED flashes slowly; release the button, LED keeps slow flash. That means all stored
codes have been deleted successfully.
Learning the button of remote control:
1) Press the button of receiver; signal LED on the receiver keeps shining. The receiver enters into status of LEARNING.
2) Press any one button on remote control. If signal LED flashes quickly 15 times and turns off, it means learning is successful.
3) When receiver is in the status of LEARNING, press again the button of receiver, signal LED turns off, learning process will be discontinued.
4) The receiver can learn several remote controls with different codes.
Application Circuit
Power LED
Power supply
_
+
+
_
+
_
OUTPUT 1
OUTPUT 2
Lamp 1
Lamp 2
Antenna
RF module
Jumper-1
Jumper-2
IC
Signal LED
Button
Relay 1
Relay 2
LED 1
LED 2