Flying Industry Development S1F2-DC06 User manual

SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: [e-mail]
RF Wireless Remote Control DC Motor Controller / Transmitter & Receiver
This DC motor controller system includes one transmitter and two controllers. You can use one transmitter to remote control two DC motors
(DC6V/9V/12V/24V) rotation in positive/ reversal direction. You also can connect two restrictive switches to each receiver and use them to stop
motor rotation.
Package Include:
2 x Receiver: S1F2-DC06 / S1F2-DC09 / S1F2-DC12 / S1F2-DC24
1 x Transmitter: CV-6-2
1 x User manual
Features:
Wireless control, easy to install
Control DC motors of rolling blinds / doors, projection screens, awnings, pumps, winches, conveyors or other appliances and mechanicals with
voltage DC6V / 9V / 12V / 24V.
You can rotate the motor in positive or reversal direction with the transmitter (remote control) from any place within a reliable distance; the
wireless signal can pass through walls, floors and doors.
Reliable control: The transmitter (Encoding) and the receiver (Decoding) use an 8-bit code.
One/several transmitters can control one/several receivers simultaneously.
If you use two or more receivers in the same place, you can set them with different codes.
Transmitting Frequency: 315MHz / 433MHz
Receiver:
Model No: S1F2-DC06 / S1F2-DC09 / S1F2-DC12 / S1F2-DC24
Coding Type: Fixed code or learning code
Coding Setting: By learning
Power Supply (Operating Voltage): DC6V (S1F2-DC06), DC9V±1V (S1F2-DC09), DC12V±1V (S1F2-DC12), DC24V±1V (S1F2-DC24)
Output: DC6V (S1F2-DC06), DC9V±1V (S1F2-DC09), DC12V±1V (S1F2-DC12), DC24V±1V (S1F2-DC24)
Case Size: 74mm x 54mm x 28mm
Quiescent Current: 5mA
Rated Current: 5A
The Maximum Instantaneous Current of Starting Motor: 10A
Transmitter:
Model No.: 0021052(CV-6-2)
Channel: 6 CH
Remote Control Distance: 500m / 1500ft (theoretically)
Encode: Fixed code by Soldering
Unit size: 110mm x 50mm x 18mm
Power Supply: 1 x 23A -12V battery (Included, can be used for 12 months)
Usage:
Power supply:
Connect power supply DC6V / 9V / 12V / 24V to terminal “INPUT”; connect motor to terminal “OUTPUT”. You can exchange the output wires of
motor to change the rotating direction of motor.
Setting control mode Latched: Connect Jumper S1
Function of transmitter:
Press button ▲, ▼,on the left to control receiver 1; Press button ▲, ▼,on the right to control receiver 2.
Press button ▲on remote: terminal “Output” output DC power, motor rotates in positive direction.
Press button ▼on remote: terminal “Output” output DC power, motor rotates in reversal direction.
Press button on remote: motor stops.
Function of manual buttons in receiver:
Press button K3 in receiver: terminal “Output” output DC power, motor rotates in positive direction.
Press button K1 in receiver: terminal “Output” output DC power, motor rotates in reversal direction.
Press button K2 in receiver: motor stops.
Setting control mode Momentary: Connect Jumper S2
Function of transmitter:
Press button ▲, ▼on the left for remote control receiver 1; Press button ▲, ▼on the right for remote control receiver 2;
Press and hold button ▲on remote: terminal “Output” output DC power, motor rotates in positive direction. Release button: motor stops.
Press and hold button ▼on remote: terminal “Output” output DC power, motor rotates in reversal direction. Release button: motor stops.
Function of manual buttons in receiver:
Press and hold button K3 in receiver: terminal “Output” output DC power, motor rotates in positive direction. Release button: motor stops.
Press and hold button K1 in receiver: terminal “Output” output DC power, motor rotates in reversal direction. Release button: motor stops.
Restrictive function:
You can connect two restrictive switches to terminals “X1” and “X2”, if the restrictive switch X1 or X2 is connected, the motor will work normally; i
f the restrictive switch X1 or X2 is disconnected, the motor will stop automatically. That means when the restrictive switch “X1” is connected, the

SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: [e-mail]
motor will work in reversal direction; when the restrictive switch “X1” is disconnected, motor will stop automatically. When the restrictive switch
“X2” is connected, the motor will work in positive direction; when the restrictive switch “X2” is disconnected, motor will stop automatically.
When you don't want to use the restrictive switches, you need to connect the terminals “X1” and “X2”by two wires.
Learning the button of transmitter:
1) Press and hold “K3”button of receiver 1; when signal LED on the receiver 1 is on, release “K3”button. Press the left ▲button of transmitter
within 5 seconds, if the signal LED off, that means learning is successful.
2) Press and hold “K1”button of receiver 1; when signal LED on the receiver 1 is on, release “K1”button. Press the left ▼button of transmitter
within 5 seconds, if the signal LED off, that means learning is successful.
3) Press and hold “K2”button of receiver 1; when signal LED on the receiver 1 is on, release “K2”button. Press the left button of transmitter
within 5 seconds, if the signal LED off, that means learning is successful.
4) Press and hold “K3”button of receiver 2; when signal LED on the receiver 2 is on, release “K3”button. Press the right ▲button of transmitter
within 5 seconds, if the signal LED off, that means learning is successful.
5) Press and hold “K1”button of receiver 2; when signal LED on the receiver 2 is on, release “K1”button. Press the right ▼button of transmitter
within 5 seconds, if the signal LED off, that means learning is successful.
6) Press and hold “K2”button of receiver 2; when signal LED on the receiver 2 is on, release “K2”button. Press the right button of transmitter
within 5 seconds, if the signal LED off, that means learning is successful.
Delete the button of transmitter:
We have learned transmitter to the receiver. If you don’t want the receiver to work with transmitter, you can delete all codes of transmitter which
are stored in the receiver. You can operate as following:
Press and hold “K3”button of receiver more 3 seconds; when signal LED on the receiver begin to flicker, then off, that means deleting is
successful.
Press and hold “K1”button of receiver more 3 seconds; when signal LED on the receiver begin to flicker, then off, that means deleting is
successful.
Press and hold “K2”button of receiver more 3 seconds; when signal LED on the receiver begin to flicker, then off, that means deleting is
successful.
Note: Before you change from motor rotates in positive direction to reversal direction or from motor rotates in reversal direction to positive
direction, you should stop rotating of motor firstly, then remote control motor.
Signal LED
Relay
Relay
Application Circuit
OUTPUT
IC
Power LED
RF module
Antenna
K2
K3
Jumper S1
Jumper S2
INPUT
M
X1
X2
Power supply
_
+
DC Motor
Restrictive switches
K1
When you use the restrictive switches
Antenna
RF module
IC
Jumper S2
Jumper S1
K2
K3
K1
Signal LED
Power LED
Relay
Relay
OUTPUT
Restrictive switches
INPUT
M
DC Motor
X2
X1
_
+
Power supply
When you don’t use the restrictive switches
Application Circuit