Flying Industry Development S1PS1-DC06-ANT2 User manual

SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Http://www.caymart.com E-Mail: [e-mail]
4 CH 2000m RF Wireless Remote Control Firework Ignitor System
Package Include:
4 x Receiver: S1PS1-DC06-ANT2 (1 Channel / DC6V)
1 x Transmitter: CB-4L
1 x User manual
Feature:
Wireless control, easy to install
It can ignite various kinds of electric fireworks directly, or ordinary fireworks through fireworks electric igniter, which reduces accidents like skin burn
and accidental explosions.
One ignitor can light several fireworks at the same time.
One transmitter can control many ignitors simultaneously.
The ignitor can be remotely controlled from any place within a reliable distance; wireless signal pass through walls, floors and doors.
More reliable than fixed code: The transmitter use EV1527 Learning code, which is up to 1 million codes, reducing code collision and unauthorized
code scanning possibilities.
Transmitting Frequency: 433MHz
Working distance of transmitter and receiver with external extend antenna: 2000M /6000ft (theoretically)
Receiver:
Model No.: S1PS1-DC06-ANT2
Channel: 1 CH
Power Supply (Operating Voltage): 4 x1.5V AA batteries (excluded)
Power Output: DC6V
Case size: 105mm x75mm x20mm
Static Current: ≤5mA
External Extend Antenna:
Frequency Range: 300~450MHz
Impedance: 50Ω
Antenna Length: 15cm
Cable Length: 150cm
Weight: 35g
Anti-interference, waterproof, shielded wire set inside
Magnetic stand design for easy to install
Transmitter:
Model No.: CB-4L
Button: 4 buttons
Remote Control Distance: 1000m / 3000ft (theoretically)
Encode: EV1527 Learning code (up to 1 million codes, reducing code collision)
Unit Size: 135mm x 42mm x 25mm
Power Supply: 1 x 6F22-9V battery (included, can be used for 12 months)
Usage:
Remote Controller Learning:
1. Put 4 pcs AA batteries to the receiver battery box and switch on the power, using a small stick to press and hold the button in the little hole on the
back side of the receiver box for 3 seconds. Then the power LED light and signal light will flash. The receiver enters into status of LEARNING.
2. Press button A on the transmitter, the signal light will be off and the power LED light flashes 2 times, then the signal light is on again. It means
learning is successful.
3. Press button B to pair with receiver 2.
…
4. Press button D to pair with receiver 4.
(We have set the receiver to learn the transmitter, you can use them directly.)
Operation:
1. Test the firework ignitor system: switch on the receiver box, press buttonAon the transmitter, signal light will be off and the power LED light flashes
2 times, then signal light is on again. It means that remote control firework ignitor system is in good condition.
2. Connect fireworks: Switch off the receiver and connect two wires of electric firework or fireworks electric igniter of firework to black and red
terminals on the receiver. Switch on the receiver after connections. The fireworks connections are correct if the signal light is on. Likewise, connect
fireworks to other receivers and use other buttons on the transmitter to test and control other corresponding receivers.
3. Ignite fireworks: Switch on each receiver box, press buttons one by one, ignite fireworks.
Caution:
1. Please make sure that the power of receiver is off when you connect two wires of electric fireworks or fireworks electric igniter to black & red
terminals.
2. Any inflammable and explosives must be far away when igniting fireworks.
3. Please make sure that anyone is far away from the firework more than 50m when it is ignited.

SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Http://www.caymart.com E-Mail: [e-mail]
External Extend Antenna
Power Switch
Power LED
Signal LED