Follett Symphony Plus 110CT425A Setup guide

Following installation, please forward this manual
totheappropriate operations person.
Order parts online:
www.follettice.com
01033729R04
801 Church Lane • Easton, PA 18040, USA
Toll free (877) 612-5086 • +1 (610) 252-7301
www.follettice.com
Installation, Operation and Service Manual
Symphony Plus™110 Series
Ice and Water Dispensers
110CT425A/W 110CR425A/W 110FB425A/W
Serial numbers below K39864

2 100CR/CT/FB Ice and Water Dispensers
Contents
Welcome to Follett. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Before you begin.......................................................................... 3
Specications .............................................................................. 4
Electrical ................................................................................ 4
Ambient................................................................................. 4
Plumbing................................................................................ 4
Ventilation clearances...................................................................... 5
Approximate shipping weight ................................................................ 5
Installation ................................................................................. 5
Before you begin.......................................................................... 5
Installing freestanding dispensers ............................................................ 5
Installing countertop dispensers.............................................................. 7
Installing RIDE ice machines ................................................................ 9
Installing top mount ice machines ........................................................... 10
User information ........................................................................... 12
How the dispenser works .................................................................. 12
How SensorSAFE infrared dispensing works .................................................. 12
Quiet Night™/Sleep cycle (does not apply to CR units) .......................................... 12
Cleaning/descaling and sanitizing ............................................................ 12
Weekly ................................................................................ 13
Monthly ................................................................................ 13
Semi-Annually (more often if conditions dictate) ................................................ 14
Ice Machine and Dispenser ................................................................ 14
Dispenser only .......................................................................... 15
Service ................................................................................... 17
Lever models ........................................................................... 17
SensorSAFE models ..................................................................... 17
Wiring diagram - Lever .................................................................... 18
Wiring diagram - SensorSAFE .............................................................. 19
Dispenser troubleshooting .................................................................. 20
Lever model troubleshooting guide .......................................................... 20
SensorSAFE model troubleshooting guide .................................................... 21
Disassembly and replacement instructions..................................................... 22
Ice transport tube replacement – Top mount units............................................... 23
Ice transport tube replacement – Freestanding and RIDE models .................................. 23
Thermostat replacement................................................................... 24
Replacement parts ......................................................................... 25
Dispenser exterior........................................................................ 25
Wheelmotor and drive system .............................................................. 26
Dispense chute and splash panel (models with lever dispensing) .................................. 27
Dispense chute and splash panel (models with SensorSAFE infrared dispensing) ..................... 28
Electrical components .................................................................... 29
Hopper components ...................................................................... 30
Ice transport tubing....................................................................... 31
Chilled water components ................................................................. 31
Dispenser plumbing connections ............................................................ 32
Solenoid dispense assembly ............................................................... 33
Water treatment accessories for Symphony Plus ice and water dispensers.......................... 34

100CR/CT/FB Ice and Water Dispensers 3
Welcome to Follett
Follett equipment enjoys a well-deserved reputation for excellent performance, long-term reliability and outstanding
after-the-sale support. To ensure that this equipment delivers that same degree of service, we ask that you take
a moment to review the installation portion of this manual before beginning to install the unit. Our installation
instructions are designed to help you achieve a trouble-free installation. Should you have any questions or require
technical help at any point, please call our technical service group at (877) 612-5086 or
(610) 252-7301.
Note: To expedite assistance, all correspondence or communication MUST include the model number, serial
number and complete and detailed explanation of the problem.
Before you begin
After uncrating and removing all packing material, inspect the equipment for concealed shipping damage. If
damage is found, notify the shipper immediately and contact Follett Corporation so that we can help in the ling
of a claim, if necessary.
Check your paperwork to determine which model you have. Follett model numbers are designed to provide
information about the type and capacity of Follett ice dispensing equipment. Following is an explanation of the
different model numbers.
Condenser type – A = air-cooled, W = water-cooled
110CT425A-L
Ice machine capacity and refrigerant – 425 = 425 lbs (193 kg)/day, R404a refrigerant
Ice machine location – R = RIDE ice machine, T = integral ice machine in top of cabinet,
B = ice machine in base of freestanding units
Approximate storage capacity in lbs
L = Lever dispensing, S = SensorSAFE infrared dispensing
CAUTION!
§Do not tilt any unit further than 30° off vertical during uncrating or installation.
§Dispenser bin area contains mechanical, moving parts. Keep hands and arms clear of this area at all times. If
access to this area is required, power to unit must be disconnected rst.
§Follett recommends a Follett water lter system be installed in the ice machine inlet water line (standard capacity
#00130229, high capacity #00978957, carbonless high capacity #01050442).
§Prior to operation clean and sanitize the dispenser in accordance with instructions found in this manual.
§Ice is slippery. Be sure counters and oors around dispenser are clean, dry and free of ice.
§Do not block right side air intake or top air exhaust.

4 100CR/CT/FB Ice and Water Dispensers
Specications
Electrical
§Models with RIDE ice machines (110CR425A/W). Ice machine and dispenser require their own separate,
dedicated circuit.
Dispenser with
ice machine
Max.
circuit
Dispenser without
ice machine
Max.
circuit
Basic electrical: 115 V/60 Hz/1 phase 11.0A 20A 4.0A 20A
§Freestanding models (110FB425A/W, 110CT425A/W) require a dedicated circuit.
Total system Max. circuit
Basic electrical: 115 V/60 Hz/1 phase 11.0A 20A
§Dispensers and RIDE ice machines are supplied with 7-foot power cord with NEMA 5-15 hospital-grade plug.
Connect to a dedicated 15A circuit.
CAUTION!
All eld wiring must be installed in accordance with NEC and local electrical codes. Field wiring diagram is
intended only to aid electrician or technician in understanding how equipment works.
Model Electrical connection Circuits required
110FB425A/W cord & plug provided 115/60/1, 15A max. fuse size
110CT425A/W cord & plug provided 115/60/1, 15A max. fuse size
110CR425A/W cord & plug provided 115/60/1
Dispenser: 15A max. fuse size,
Ice machine: 15A max. fuse size
Ambient
Air temp* 100 F/38 C Max. 50 F/10 C Min. (Best performance below 80 F/27 C)
Water temp†90 F/32 C Max. 45 F/7.2 C Min. (Best performance below 70 F/21 C)
Water pressure 70 P.S.I./5Bar Max. 10 P.S.I./0.7 Bar Min.
* Ambient air temperature is measured at the air-cooled condenser coil inlet.
† Ambient water temperature is measured in the ice machine reservoir.
Plumbing
110CR with RIDE ice
machine
110CT with integral
ice machine
110FB with ice
machine in base
Dispenser drain 3/4" MPT 3/4" MPT 3/4" MPT
Ice machine drain 3/4" MPT 3/4 MPT 3/4" MPT
Dispenser water inlet 3/8" FPT 3/8" FPT 3/8" FPT
Ice machine water inlet — 3/8" FPT —
RIDE IM water inlet 3/8" FPT — —
Cond. inlet – w/c only 3/8" FPT 3/8" FPT 3/8" FPT
Cond. drain – w/c only 3/8" FPT 3/8" FPT 3/8" FPT
Note: Water shut-off recommended within 10 ft (3 m) of dispenser. Drain to be hard-piped and insulated. Maintain at
least 1/4" per foot (20 mm per 1 m) run of slope.

100CR/CT/FB Ice and Water Dispensers 5
Ventilation clearances
§No clearance required for countertop models with RIDE ice machine (110CR425A/W).
Note: 12" (30.5 cm) at top advised for service.
§6" (15.2 cm) required at top (110CT425A/W).
Note: 6" (15.2 cm) at each side advised for service.
§4" (10.2 cm) required at rear (110FB425A/W).
Note: 12" (30.5 cm) at top advised for service.
Approximate shipping weight
§290 lb (132 kg), base stand: 140 lb (64 kg)
Installation
Before you begin
§All dispensers must be installed level in both directions to ensure proper operation.
§All countertop dispensers provide the option of taking utilities out the bottom or back of the dispenser.
See counter cut-out (Fig. 2) for bottom exiting utilities on units with and without drain pans. For installations
where utilities will exit through back of dispenser, refer to back view drawings.
§SensorSAFE dispensers are shipped with a plastic, protective lm on sensor lenses. For proper operation, plastic
lm must be removed after installation.
Installing freestanding dispensers
1. Position dispenser in desired location and adjust legs to level in both directions.
2. Connect water supply to 3/8" FPT tting on back of dispenser (Fig. 1).
3. Connect separate drain lines to 3/4" MPT dispenser drain tting, and 3/4" MPT ice machine drain tting
on back of dispenser.
4. Run drain lines to wall or oor drain. If ice machine drain tting is below an intended wall drain, a
condensate pump must be used.
5. If ice machine is a water-cooled unit, connect water-cooled condenser supply line to 3/8" FPT condenser
inlet tting on back of dispenser.
Note: Do not run condenser supply water through ice machine water lter system.
6. Connect condenser drain line to 3/8" FPT condenser outlet tting on back of dispenser.
Important: Do not connect condenser drain line to any other drain lines.
7. Plug dispenser into 15A rated NEMA 5-15 circuit.
8. Remove front cover of base section by removing two screws at bottom corners of cover. Allow cover to
drop approximately 3/8" (5 mm) and pull forward.
9. Turn on water supply and check for leaks.

6 100CR/CT/FB Ice and Water Dispensers
Fig. 1 – Rear connections, freestanding models
3/8" FPT condenser outlet location
(water-cooled only)
3/4" MPT ice machine drain location
access panel
3/8" FPT
water inlet
3/4" MPT drain
power cord
NEMA 5-15
3/8" FPT condenser outlet location
(water-cooled only)
2.75"(6.8 cm)
3.75"(9.3 cm)
4.5"(11.4 cm)
4.75"(11.9 cm)
12.25"(31.2 cm)
33.75" (85.8 cm)
31.5" (80 cm)
14" (35.7 cm)
12.38" (31.4 cm)
9.62" (24.4 cm)
10. Remove top front cover by removing two screws at bottom corners of cover. Lift cover slightly and pull
forward.
11. If dispenser is equipped with SensorSAFE remove protective plastic coating from dispense sensor labels.
12. Turn on dispenser power and bin signal rocker switches. Check dispenser and ice machine operation.
13. Sanitize ice machine according to instructions in ice machine manual. Discard ice made during sanitizing
process.
14. Turn off ice machine bin signal switch.
15. Remove dispenser hopper lid; sanitize dispenser according to instructions beginning on page 12.
16. Turn ice machine bin signal switch on and replace front covers, securing with screws.

100CR/CT/FB Ice and Water Dispensers 7
Installing countertop dispensers
CAUTION!
Dispensers with top mount ice machines cannot
be mounted on legs. They must be bolted to
counter. Use gloves when lifting ice machine to
protect hands from sheet metal edges.
1. Position dispenser in desired location, mark
dispenser outline on counter and remove
dispenser.
2. Regardless of whether utilities will exit
through back or bottom of dispenser, drill
four (4) 3/8" holes in counter to anchor
dispenser to counter (Fig. 2).
Follett countertop dispensers can have any or all
utilities run directly through counter or out rear of
dispenser. For dispensers with any utilities exiting
through counter, make counter cut-out (Fig. 2).
3. For utilities exiting through bottom only:
(a) Make cut out as shown in
Fig. 2.
(b) Move drain tting from back of dispenser
and mount where shown in Fig.3.
(c) Cut drain tube to length and attach to barbed
connection.
(d) Move inlet water tting from back of
dispenser and mount where shown in Fig.3.
(e) Cut water tubing to length and re-insert into
water tting.
4. If ice transport tube will exit out rear of
dispenser, remove ice transport tube knock-
out from rear of dispenser. Install supplied
grommet for CR models.
Note: Utility connections can be accessed through
front of dispenser by removing stainless
steel splash panel, or by removing access
panel (Fig. 4) on back of dispenser.
Fig. 2
14.00" (35.6 cm)
9.25"
(23.5 cm)
2.00" (5.1 cm)
17.31"
(44.0 cm)
23.63" (60.0 cm)
UNDERSIDE VIEW OF DISPENSER
1.50"
(3.8 cm)
0.44"
(11 mm)
CUTOUT
Fig. 3 – Bottom exiting utilities (countertop units)
bracket
inlet
tting
drain
tting
drain tube

8 100CR/CT/FB Ice and Water Dispensers
Fig. 4 – Rear connections, countertop models
12.25" (31 cm)
0.78" (20 mm)
8.22" (20.8 cm)
1.34" (35 mm)
35.91" (91 cm)
38.97" (99 cm)
41.97" (106 cm)
44.97" (114 cm)
6.06" (15.5 cm)
8.22" (201 cm)
DRAIN
3/4" NPT MALE
WATER INLET
(INTERNAL)
3/8" NPT FEMALE
DRAIN
3/4" NPT MALE
POTABLE WATER INLET
3/8" NPT FEMALE
CONDENSER OUTLET
3/8" NPT FEMALE
WATER COOLED ONLY
CONDENSER INLET
3/8" NPT FEMALE
WATER COOLED ONLY
ACCESS PANEL
5. If power is to be supplied through counter cut-out, complete steps 6-9. If power is to be supplied through
rear of dispenser, proceed to step 10.
6. Temporarily remove rear access panel (Fig. 4) from rear of dispenser.
7. Loosen junction box mounting screws. Lift junction box and power cord up until cord and mounting
screws clear notches on rear panel of dispenser. Remove Phillips head screws from right side of junction
box.
8. Rotate junction box 90 degrees so that screw holes on right side of junction box align with holes on rear
dispenser panel. Resecure junction box to dispenser using Phillips head screws.
9. Place power cord inside dispenser and replace access panel (Fig. 4) to rear of dispenser.
Note: For dispensers to be installed with utilities connected through rear of dispenser, it may be easier to make
preliminary connections before dispenser is set in place.
10. Apply a thick bead, approximately. 1/4" (6 mm) diameter, of NSF listed silicone sealant (Dow-Corning*
RTV-732 or equivalent) 1/4" (6 mm) inside marked outline of dispenser.
11. Carefully position dispenser on counter.
12. Remove four screws securing splash panel to front of dispenser and gently lay splash panel on counter.
(Water line to solenoid valve can be disconnected from water inlet valve by pushing on ring at end of inlet
tting while pulling on tubing.)
13. Secure dispenser to counter with four 3/8" bolts (supplied by others).
14. Smooth excess sealant around outside of dispenser.
15. Proceed with either RIDE or top-mounted ice machine connection instructions, as appropriate.
* Dow Corning is a registered trademark of Dow Corning Corporation in the United States and other countries

100CR/CT/FB Ice and Water Dispensers 9
Installing RIDE ice machines
CAUTION!
See Ice Machine Installation Manual (form #01062587) for critical installation instructions for RIDE ice machines.
Failure to comply with these instructions will result in poor performance and void warranty.
1. Install RIDE ice machine following instructions in ice machine manual.
2. If dispenser is equipped with SensorSAFE remove protective plastic coating from dispenser lenses.
3. Remove top front cover by removing two screws at bottom corners of cover. Lift cover slightly and pull
forward. Turn on power and bin signal rocker switches. Replace front cover and secure with screws. Test
operation.
4. Sanitize ice machine following instructions in ice machine manual. Discard ice made during sanitizing
process.
5. Sanitize dispenser hopper following instructions on page 12. Installation is complete.
Fig. 5 – Ice transport tube and ice level control stat mounting for freestanding dispensers and countertop
units with RIDE ice machine
0.187 (5 mm) ice tube hole
ice hose mounting bracket
ice level control stat engaging pin
ice tube
1.00"
(25.4 cm)

10 100CR/CT/FB Ice and Water Dispensers
Installing top mount ice machines
Models 110CT425A/W
CAUTION!
Dispensers with top mount ice machines cannot be mounted on legs. They must be bolted to counter. Use gloves
when lifting ice machine to protect hands from sheet metal edges. See Ice Machine manual.
1. Remove dispenser top front cover by removing two screws at bottom corners of cover, lifting cover slightly
and pulling forward.
2. Remove ice machine compartment top and side panels.
3. Remove ice machine hold-down bracket from front of ice machine compartment.
4. Lift ice machine onto dispenser top and slide ice machine completely into position, compressor end rst.
5. Reinstall hold-down bracket on front of ice machine with power cord and bin signal cords in notch. Do not
cut or pinch cords.
6. Insert loose end of ice transport tube through bracket (on ice machine base) into hopper access hole.
Tighten transport tube clamp screw to secure ice transport tube.
7. Connect plastic water supply line to water ll solenoid.
Tighten clamp
screw
1.00" (2.54 cm)
2
1
3

100CR/CT/FB Ice and Water Dispensers 11
8. Connect molded drain tube to evaporator drain pan, purge solenoid and rear drain tting.
CLEANING CUP
WATER SUPPLY
3/8" FPT, 45-90 F (7-32 C)
10-70 PSI (69-483 KPA)
RESERVOIR FILL
SOLENOID
WATER
RESERVOIR
EVAPORATOR
ICE
NOZZLE
DRAIN PAN
VENT
TO DRAIN CUP
9. Connect dispenser bin signal cable to two-pin receptacle on the ice machine electrical box ➊and
connect the three-pin receptacle to the ice machine electrical box ➋.
1
2
10. On dispensers equipped with water-cooled ice machines, connect condenser water supply and drain
lines to condenser ttings on ice machine.
11. Turn on water supply and check for leaks.
12. Plug dispenser power cord into 15A rated NEMA 5-15 circuit.
13. If dispenser is equipped with SensorSAFE, remove protective plastic coating from dispense sensor
labels.
14. Turn on power and bin signal rocker switches and test operation.
15. Sanitize ice machine following instructions in ice machine manual.
16. Remove dispenser hopper access lid and sanitize dispenser according to instructions on page 12.
1 7. Replace front cover and secure with screws. Installation is complete.
ice level control thermostat 0.75" (19 mm)
Hand bend cap tube
end to approximately
45° as shown
45°

12 100CR/CT/FB Ice and Water Dispensers
User information
How the dispenser works
Follett’s 110 series automatic-load ice and water dispensers are equipped with Follett’s 425 lb (193 kg)/day ice
machine. In the continuous icemaking process, water freezes to the inside wall of the evaporator. A rotating
stainless steel auger carries the ice to the top of the evaporator where it is compressed and extruded through an
outlet port. The ice is then pushed through a tube to the storage hopper. When the hopper is full, a bin thermostat
opens and shuts the ice machine off. When the dispense mechanism is activated, a dispense motor is turned on,
causing the wheel to turn. This moves ice to the dispense chute where it drops by gravity into the container held
below the chute.
How SensorSAFE infrared dispensing works
Follett’s SensorSAFE infrared dispensing maximizes sanitation and minimizes the possibility of cross-
contamination by eliminating physical contact between the cup or container and dispenser. Sensors in the panel
use reected infrared light to detect the presence of the container and send a signal to a control board which then
activates the appropriate components for ice or water dispensing.
The SensorSAFE infrared dispensing package includes a cleaning switch under the left side of the front cover
which temporarily shuts off dispensing to allow cleaning of the panel and lenses. If the switch is not turned back on
after cleaning, the dispenser automatically resets after two minutes for normal operation.
SensorSAFE infrared dispensing also includes a time limit safety feature which automatically stops ice dispensing
after one minute of continuous dispensing. Dispensing can be resumed by moving the container away from the
dispenser and returning it to the activation zone.
Quiet Night™/Sleep cycle (does not apply to CR units)
The board monitors ice dispensing through a line voltage input to P15. If the ice dispense has not been initiated for
more than 5 seconds during the 20 minute time delay, the SLEEP CYCLE LED comes on. The machine will stay
off for 12 hours unless 5 seconds of dispensing is seen. After 12 hours, the SLEEP CYCLE LED goes out and the
ice making will resume if the bin thermostat is closed. The sleep cycle can be deated using the DIP switches on
the ice machine control board.
Cleaning/descaling and sanitizing
Follett ice machines and dispensers, and their associated cleaning and sanitizing procedures, are designed for
use with potable water sources. The presence, or suspected presence, of infectious agents may call for additional
measures, including the replacement of components and more comprehensive disinfection measures. Follett
recommends that these cleaning and sanitizing procedures be reviewed with the appropriate infectious agent
subject matter experts to assure complete remediation.
Periodic cleaning/descaling and sanitizing of Follett’s ice and water dispenser and ice machine system is required
to ensure peak performance and delivery of clean, sanitary ice. The recommended cleaning procedures that follow
should be performed at least as frequently as recommended and more often if environmental conditions dictate.
Follett recommends sanitizing the pressurized water lines prior to cleaning/descaling and sanitizing the ice
machine/dispenser. Follett offers two kits: order P/N 01089572 when a Follett lter system with a pre-lter bowl
is present, or P/N 01089580 when a Follett lter system is not present. Follow the instructions provided with the
respective kits to sanitize the pressurized water lines immediately before cleaning/descaling and sanitizing the ice
machine/dispenser.
Cleaning of the condenser can usually be performed by facility personnel. Cleaning/descaling and sanitizing of
the ice machine system should be performed by your facility’s trained maintenance staff or a Follett authorized
service agent. Regardless of who performs the cleaning, it is the operator’s responsibility to see that this cleaning
is performed according to the schedule below. Service problems resulting from lack of preventive maintenance will
not be covered under the Follett warranty.

100CR/CT/FB Ice and Water Dispensers 13
Recommended cleaning/descaling and sanitizing intervals*
Symphony Plus Frequency
Drain Line weekly
Drain Pan/Drip Pan weekly
Exterior, Water Station Tube as needed
Condenser monthly (air-cooled only)
Dispenser and Components semi-annually
Ice Machine semi-annually
Transport Tube semi-annually
Ice Storage Area/Bin semi-annually
Pressurized Water Sanitizing semi-annually
* Ice machine and dispenser must be sanitized prior to start-up.
Weekly
CAUTION!
§Do not use solvents, abrasive cleaners, metal scrapers or sharp objects to clean any part of the dispenser.
Dispenser drain pan and drain line
1. Pour 1 gal. (3.8 L) of hot tap water into drain pan to ush drains.
Splash panel front, SensorSAFE infrared dispensing
1. Deactivate dispensing by pressing and releasing clean switch located on left side of unit under top front
cover.
2. Clean lens and splash panel front using a soft cloth and mild, non-abrasive, non-chlorine based cleaner.
3. Reactivate dispensing by pressing and releasing clean switch again.
Monthly
CAUTION!
§Do not use solvents, abrasive cleaners, metal scrapers or sharp objects to clean any part of the dispenser.
Condenser (air-cooled ice machine only)
1. Use a vacuum cleaner or stiff brush to carefully clean condenser coils of lint and debris to ensure optimal
performance.

14 100CR/CT/FB Ice and Water Dispensers
Semi-Annually (more often if conditions dictate)
§A cleaning/descaling and sanitizing procedure should always include both the ice machine and dispenser.
§Icemaking system can be cleaned/descaled in place.
CAUTION!
§Wear rubber gloves and safety goggles (or face shield) when handling cleaner or sanitizer mixtures.
§Use only Follett approved cleaners.
§It is a violation of Federal law to use Cleaning or Sanitizing solution in a manner inconsistent with their labeling.
§Do not use solvents, abrasive cleaners, metal scrapers or sharp objects to clean any part of the dispenser.
Cleaning: Following manufacturer’s instructions, mix cleaning solution of 1 gal. (3.8 L) 100 F (38 C) water
and 7 oz (198 g) (one 7oz packet) of Follett SafeCLEAN™ ice machine cleaner/descaler
(P/N00132001).
Sanitizing: Following manufacturer’s instructions, mix a sanitizing solution of 1 gal. (3.8 L) 100 F (38 C) water
and 1.6oz (48 ml) Nu-Calgon IMS-II or IMS-III Sanitizer (P/N 00979674).
Cleaning & Sanitizing Tool Checklist
§(2) 1.5 Gallon (or larger) Plastic Buckets
§(2) clean cloths
§Sanitary gloves
§Safety Glasses
§(2) Sani-Sponge™ (P/N 00131524 - single sponge)
§(1 ) Packet of SafeCLEAN™ (P/N 00132001 - 24 packets)
§1.6 oz of Nu-Calgon IMS-II or IMS-III Sanitizer (P/N 00979674 - 16 . oz bottle)
Ice Machine and Dispenser
Cleaning/Descaling Procedure
Note: Check drains and drain cup to ensure they are open and owing freely.
1. Remove front cover and turn OFF bin signal switch.
2. Dispense all ice from storage hopper and discard.
Note: CI Models only: remove splash panel.
3. Press CLEAN switch. The MAINTENANCE light will turn on and the machine will drain. Wait for the LOW
WATER light to turn on.
4. Remove lid from cleaning cup and ll (about 1 quart) until cleaning solution completely lls the reservoir.
Place lid back on cup. Save remainder of cleaning solution.
5. CLEANER FULL light will turn on and machine will start cleaning cycle then rinse three times; this
process takes approximately 15 minutes.
6. While ice machine is cleaning/descaling, clean dispenser as follows:
a. Turn OFF dispenser power.
b. Remove hopper lid. (Note: for CT models, remove hopper access cover)
c. Remove knurled nuts from front of storage hopper.
d. Remove stud assembly, baffle, wheel, and any remaining ice.
e. Remove dispense chutes from splash panel.
f. Submerse drain grill in cleaning solution and allow to soak to remove any scale buildup.
g. Wipe stud assembly, baffle, wheel, inside of storage area, dispense chutes, drain grill and drain pan with
damp cloth wrung out in cleaning solution. Thoroughly rinse all parts with damp cloth wrung out with clean
water.
Note: To avoid possible damage to motor assembly, only use a damp cloth to clean storage hopper. Do not
allow water to run through motor shaft hole in bottom of hopper.
7. When machine is nished cleaning, the MAINTENANCE light will turn off.

100CR/CT/FB Ice and Water Dispensers 15
Sanitizing Procedure
8. Press CLEAN switch. The MAINTENANCE light and LOW WATER light will turn on.
9. Fill cleaning cup until sanitizing solution completely lls the reservoir. Place lid back on cup. Save
remainder of sanitizing solution.
10. CLEANER FULL light will turn on and machine will start sanitizing cycle then rinse three times; this
process takes approximately 15 minutes.
11. While ice machine is sanitizing, sanitize dispenser as follows:
a. Wipe inside of hopper lid, stud assembly, baffle, wheel, inside of storage area, dispense chutes, drain grill
and drain pan with damp cloth wrung out in sanitizing solution.
Note: To avoid possible damage to motor assembly, only use a damp cloth to clean storage hopper. Do
not allow water to run through motor shaft hole in bottom of hopper.
b. Reinstall dispense chutes, wheel, baffle, stud assembly and knurled nuts. (See manual for correct baffle
position.)
12. When machine is nished rinsing, the MAINTENANCE light will turn off. Loosen phillips-head screw on
nozzle connected to evaporator. Remove nozzle from evaporator side only, leave other side of nozzle
connected to transport tube.
13. Place one Sani-Sponge in remaining sanitizing solution.
14. Insert the sponge soaked in sanitizing solution into nozzle then insert a dry sponge into the nozzle.
15. Replace nozzle onto evaporator and tighten screw. Ensure drain is connected to reservoir and vent tubes
are connected to evaporator drain pan.
16. Turn ON bin signal switch. Wait for ice to push sponges through transport tube.
1 7. Collect sponges from ice storage bin.
18. Replace hopper lid (access cover for CT models), machine top, turn ON dispenser power and install
front cover.
19. After 10 minutes, dispense all ice and discard.
Dispenser only
Cleaning/descaling procedure
Note: Check drains and drain cup to ensure they are open and owing freely.
1. Remove and discard all ice from storage hopper.
2. Ensure power is disconnected. Working inside storage area, remove center thumbscrew from dispense
wheel, tilt wheel up toward back to clear baffle and disengage wheel from motor shaft.
3. Remove dispense chutes.
4. Thoroughly wipe lid, dispense wheel, baffle and dispense chutes with cloth soaked in cleaning solution.
5. Wipe all bin surfaces (including the area under dispense wheel) with a damp cloth wrung out in cleaning
solution.
Note: To avoid possible damage to dispense motor assembly, use only a damp cloth to clean the
storage bin. Do not allow water to run through bottom of bin area.
6. Remove grille and wash with cleaning solution. Rinse thoroughly with clean water.
7. Rinse all above items with damp cloth wrung out in clear water.

16 100CR/CT/FB Ice and Water Dispensers
Sanitize dispenser
8. Wipe all above items with damp cloth wrung out in sanitizing solution to sanitize. Do not rinse.
9. Reinstall all parts and replace any panels removed prior to cleaning.
10. Pour 1 gal. (3.8 L) of hot tap water into drain pan to ush drains.
11. If the dispenser is equipped with a Chilled Water Accessory continue to Step 11.1; if not, skip to Step12.
11.1 Remove four screws securing splash panel.
11.2 Disconnect 3/4" (19 mm) drain line from bottom of chilled water canister.
11.3 Loosen (do not remove) screw securing front bracket of chilled water canister to bottom of dispenser
hopper.
11.4 Rotate canister clockwise to release front bracket, then pull canister forward to disengage rear
bracket.
11.5 Remove chilled water coil from canister and clean with cloth wrung out in cleaning solution.
11.6 Wipe inside of chilled water canister with cloth wrung out in cleaning solution.
11.7 Rinse all above items with damp cloth wrung out in clear water.
11.8 Sanitize all above items with damp cloth wrung out in sanitizing solution. Do not rinse.
11.9 Reinstall chilled water coil into canister (rubber alignment grommet on coil tubing must be located
outside chilled water canister to hold coil securely against canister wall).
11.10 Reinstall chilled water assembly on dispenser and tighten screw securing front bracket.
11.11 Reconnect 3/4" (19 mm) drain line to chilled water canister.
11.12 Reinstall splash panel and top front cover.
12. If so equipped, turn ice machine ON and begin to make ice (ice machine should start immediately with
power and bin signal supplied).
13. After approximately 30 minutes, test dispenser for proper dispensing.

100CR/CT/FB Ice and Water Dispensers 17

18 100CR/CT/FB Ice and Water Dispensers
Wiring diagram - Lever
4
2
3
1
8
9
5
7
6
T-STAT
BIN
SIGNAL
SWITCH
1 2 3 4
POWER
SWITCH
1 2
NO
NC
COM
RELAY 2
7
A
1
4
INPUT
LOAD
9
B1 2 3
3
6
TIMER
NO
NC
COM
RELAY 1
7
A
1
4
9
B
3
6
107 BLACK41GREEN
43 BLACK
49 BLACK
44 RED
45 BLUE
46 PURPLE
42 WHITE
48 WHITE
93 BLACK
94 WHITE
95 GREEN
96 BLACK
117 BLACK
114 WHITE
117 BLACK
110 PURPLE
118 WHITE
104 WHITE
44 RED
108 BLACK
109 BLACK
99 BLACK
102 WHITE
101 BLACK
98 BLACK
97 WHITE
100 BLUE
111 WHITE
47 ORANGE
CT ICE
MACHINE
POWER
CT ICE MACHINE
BIN SIGNAL
(CONTACT CLOSURE)
2
3
1
102 WHITE
104 WHITE
114 WHITE
118 WHITE
111 WHITE
47 ORANGE
110 PURPLE
4
SCREW
GROUND
1
3
2
1 2
7
6
5
8
39 BLACK
38 BLACK
9
31 GREEN
32 WHITE
33 BLACK
39 BLACK
38 WHITE
34 RED
35 BLUE
36 PURPLE
37 ORANGE
1 2 3 4
74 GREEN
75 BLACK
72 BLACK
73 WHITE
NEUTRAL-WHITE
GROUND-GREEN
115/1/60-BLACK
1
POWER
BOX
4x4
4
2
3
577 RED
35 BLUE
37 ORANGE
76 WHITE
36 PURPLE
74 GREEN
79 BLACK
78 WHITE
100 BLUE
96 BLACK
GROUND
SCREW
1
2
MDISPENSE
MOTOR
91 WHITE
92 PURPLE
LEVER DISPENSERS
SPLASH PANEL
LEVER DISPENSERS
CONTROL BOX
S2
3
1
WHITE
ORANGE
DISPENSE GATE SOLENOID
FB/CR ICE MACHINE BIN SIGNAL
(CONTACT CLOSURE)
FB/CR ICE MACHINE POWER
1
4
2
3
5
S
87 WHITE
86 WHITE
88 BLUE
89 PURPLE
85 ORANGE
82 BLUE
83 PURPLE
81 WHITE
84 RED
ICE
STATION
SWITCH
WATER
SOLENOID
90 PURPLE
WATER
STATION
SWITCH
1
2

100CR/CT/FB Ice and Water Dispensers 19
Wiring diagram - SensorSAFE
ICE
NEUTRAL
WM
SOL
WTR
CLN
WTR
TO
SPLASH
PANEL
L1
GND
4
2
3
1
8
9
5
7
6
T-STAT
BIN
SIGNAL
SWITCH
1 2 3 4
POWER
SWITCH
1 2
NO
NC
COM
RELAY 2
7
A
1
4
INPUT
LOAD
9
B1 2 3
3
6
TIMER
NO
NC
COM
RELAY 1
7
A
1
4
9
B
3
6
107 BLACK41 GREEN
43 BLACK
49 BLACK
44 RED
45 BLUE
46 PURPLE
42 WHITE
48 WHITE
93 BLACK
94 WHITE
95 GREEN
96 BLACK
45 BLUE
116 PURPLE
108 BLACK
117 BLACK
118 WHITE
114 WHITE
117 BLACK
110 PURPLE
118 WHITE
110 PURPLE
114 WHITE
104 WHITE
116 PURPLE
108 BLACK
119 PURPLE
109 BLACK
104 WHITE
102 WHITE
99 BLACK
102 WHITE
101 BLACK
98 BLACK
97 WHITE
100 BLACK
103 GREEN
100 BLACK
111 WHITE
112 ORANGE
105 WHITE
106 BLACK
CT ICE
MACHINE
POWER
CT ICE MACHINE
BIN SIGNAL
(CONTACT CLOSURE)
2
3
1
GROUND
SCREW
WATER SENSOR
ICE SENSOR
BOX
TO
SensorSAFE
DISPENSERS
SPLASH PANEL
SensorSAFE
DISPENSERS
CONTROL BOX
CLEAN
SWITCH
4
SCREW
GROUND
1
3
2
1 2
7
6
5
8
39 BLACK
38 BLACK
9
31 GREEN
32 WHITE
33 BLACK
39 BLACK
38 WHITE
34 RED
35 BLUE
36 PURPLE
37 ORANGE
1 2 3 4
74 GREEN
75 BLACK
72 BLACK
73 WHITE
NEUTRAL-WHITE
GROUND-GREEN
115/1/60-BLACK
FB/CR ICE
MACHINE
POWER
FB/CR ICE
MACHINE
BIN SIGNAL
(CONTACT CLOSURE)
1
POWER
BOX
4x4
4
2
3
577 RED
35 BLUE
37 ORANGE
76 WHITE
36 PURPLE
74 GREEN
79 BLACK
78 WHITE
1
4
2
3
5
S
1
2
87 WHITE
86 WHITE
82 BLUE
83 PURPLE
81 WHITE
WATER
SOLENOID
1
2
MDISPENSE
MOTOR
91 WHITE
92 PURPLE
S2
3
1
WHITE
ORANGE
DISPENSE GATE SOLENOID

20 100CR/CT/FB Ice and Water Dispensers
Dispenser troubleshooting
CAUTION!
§Disconnect power to unit before putting hands or arms in storage area or attempting any repair or service to
equipment.
Before calling for service
1. Check that no ice is in the dispenser bin area.
2. Check that congealed ice is not causing a jam.
3. Check that all switches and circuit breakers are on.
4. Check that all drains are clear.
Lever model troubleshooting guide
Problem Indicators Corrective Action
Does not dispense ice. 1. Power switch off or faulty.
2. Faulty dispense switch.
3. Wheelmotor malfunction.
1. Check switch – turn on or replace if
faulty.
2. Replace switch.
3. Check motor and capacitor and replace.
Does not dispense water. 1. Dispense switch contacts
burned shut.
2. Debris preventing valve from
closing.
1. Replace water solenoid valve.
2. Replace dispense switch.
3. Check switch - turn on or replace if faulty.
Water runs continuously. 1. Faulty water solenoid valve.
2. Faulty dispense switch.
3. Power switch off or faulty.
1. Check switch and replace if faulty.
2 Remove and clean valve.
Dispense wheel rotates
continuously.
Dispense switch contacts are
burned out.
Replace dispense switch.
Ice machine runs continuously. Faulty or incorrectly positioned
bin stat.
Check for proper positioning. If stat does
not open when ice is placed on capillary
tube, replace stat.
Ice dispenses by itself. 1. Baffle not adjusted properly.
2. Faulty dispense switch.
1. See Adjustment Instructions.
2. Replace dispense switch.
Not making ice. 1. Dispenser is in sleep mode. 1. Verify sleep mode LED is illuminated on
control board.
2. Dispense 5 seconds worth of ice to reset.
This manual suits for next models
7
Table of contents
Other Follett Dispenser manuals

Follett
Follett Symphony Plus 110 Series User manual

Follett
Follett CVU300 Series Setup guide

Follett
Follett CVU155N Series Setup guide

Follett
Follett Symphony Plus 12 Series User manual

Follett
Follett Symphony 12CI400A Setup guide

Follett
Follett Chewblet 7 Series Setup guide

Follett
Follett C125A Setup guide

Follett
Follett C25R5A/W Guide

Follett
Follett U150 Guide

Follett
Follett 7CI100A Setup guide