Follett Horizon Chewblet series User manual

208264
StockMo dule Identification Plate
Service No.
Module No.
Product
REFRIGERANT
MODEL
MOTORCOMPRESSORTHERMALLYPROTECTED
EastonPennsylvania
FULLLOADAMPS
MAX.BRANCHCIRCUITFUSESIZE
MIN.BRANCHCIRCUITAMPACITY
DESIGNPRESSUREHIGH SIDE
AMPS
AMPS
VOLTS
CORPORATION
SERIALNO
PHASE
SINGLE
CHARGE
LOWSIDE
PARTNO
PSIG
THEUSA
MADEIN
OZ
R
C
R
HZ
UL
L
NSF
U
Order parts online
www.follettice.com
Horizon™Ice Machine Installation Instructions
for Ice Storage Bin Top-mount Applications
HCD/HMD/HCF/HMF1000RBT, HCD/HMD/HCF/HMF1400RBT, HCD/HMD/HCF/HMF1650RBT,
HCD1000NBT, HMD1000NBT, HCD1400NBT, HMD1400NBT, HCD1650NBT, HMD1650NBT
(See model number congurator on page 2 for details.)
remote condensing
00159962R09
801 Church Lane • Easton, PA 18040, USA
Toll free [phone] • [phone]
www.follettice.com

2remote condensing BIN • TOP-MOUNT
ConfigurationApplication
S RIDE™
(RIDE remote
ice delivery
equipment)
T Top-mount
400 up to
454 lbs
(206kg)
1000 up to
1036 lbs
(471kg)
1400 up to
1450 lbs
(658kg)
1650 up to
1580 lbs
(717kg)
V Vision™
H Harmony™
B Ice storage bin
J Drop-in
M Ice Manager
diverter valve
system
CondenserSeriesVoltageIcemaker
C 208-230/60/1 (icemaking head)
Self-contained only.
D 115/60/1 (icemaking head)
Self-contained and remote. If remote
unit, high side is 208-230/60/1.
E 230/50/1 (icemaking head)
Self-contained only.
F 115/60/1 (icemaking head)
Remote only. High side is
208-230/60/3.
MC Maestro™
Chewblet®
(400 Series)
HC Horizon
Chewblet
(1000, 1400,
1650 Series)
HM Horizon
Micro Chewblet
HC 1400CSVA
A Air-cooled, self-contained
W Water-cooled, self-contained
R Air-cooled, remote condensing unit
N Air-cooled, no condensing unit for
connection to parallel rack system
Chewblet®Ice Machine Model Number Configurations

BIN • TOP-MOUNT remote condensing 3
Front cover
8
Internal connection
7
Ice transport tube
5
External connection
6
Louvered docking assembly
4
Bin preparation
3
Site preparation
2
Unpack
1
Read and complete the following 8 installation steps

4remote condensing BIN • TOP-MOUNT
Carefully unpack and inspect the contents of your Follett ice machine. 1
Unpack
1/2"
1/2"
➊➋
➌➍
➎➏
Unpack ice machine
1. 1

BIN • TOP-MOUNT remote condensing 5
Prepare the installation site. 2
Site preparation
Provide drainage, water supply and electrical power to within 6 feet (2m) of ice
machine in accordance with local and national codes. Outdoor installation is
not recommended and will void warranty.
➊
NEMA
5-15
➎3/8" ∅ (9,5mm)
➍
208264
StockModule Identification Plate
ServiceNo.
ModuleNo.
Product
REFRIGERANT
MODEL
MOTORCOMPRESSORTHERMALLYPROTECTED
EastonPennsylvania
FULLLOADAMPS
MAX.BRANCHCIRCUITFUSESIZE
MIN.BRANCHCIRCUITAMP
ACITY
DESIGNPRESSUREHIGHSIDE
AMPS
AMPS
VOLTS
CORPORA
TION
SERIALNO
PHASE
SINGLE
CHARGE
LOWSIDE
P
ARTNO
PSIG
THEUSA
MADEIN
OZ
R
C
R
HZ
U
L
L
NSF
U
1/4"
1'
➌
➋
Electrical ➊
120/60/1-6 amps
Potable water supply ➋
• 10-70 psi (69-483kpa)
• 45-90 F (7-32 C)
• Follett recommends the use of an in-line water ltration system (item# 00130286)
Drain ➌
• The drain line from the ice machine must have at least 1/4" per foot pitch (6,4mm/.3m)
Refrigeration lines ➍
• 1000, 1400: 5/8" (15,8mm) diameter suction (insulated) ➍
• 1650: 7/8” (22,2mm) diameter suction (insulated) ➍
• 3/8" (9,5mm) liquid ➎
2.1 Installation site requirements
2.1

6remote condensing BIN • TOP-MOUNT
Prepare the bin. 3
Bin preparation
• Remove protective tape from
gaskets
Bin top preparation
3.1
➋
➊
➊
➌
• Apply gaskets
➊
• Install shuttle actuator ➋through bin top
and secure with locking nut ➌
Bin top preparation
3.2

BIN • TOP-MOUNT remote condensing 7
Install the louvered docking assembly.
Louvered docking assembly 4
1" (25,4mm)
Stub Typ
3" (76mm)
1-3/4" (44,5mm)
3" (76mm)
3/8" ∅
high pressure
line
➋
➊
1000, 1400:
5/8" ∅ low pressure line
1650:
7/8" ∅ low pressure line
• Mount louvered docking assembly ➊
• “Rough-in” the refrigerant piping ➋
2.1 Louvered docking assembly
4.1

8remote condensing BIN • TOP-MOUNT
➊
• Braze supplied expandable refrigerant
lines in place ➊
Refrigerant lines
4.2

BIN • TOP-MOUNT remote condensing 9
Ice transport tube
Install the ice transport tube. 5
➋
➊
➌
Hot Water
160 F (71 C)
5.1
• Slide insulation onto ice transport tube
• Heat end of transport tube in cup of 160 F (71 C) hot water to soften and spread with
pliers ➊before making connection to ease assembly
• Connect ice transport tube to coupling on louvered docking station ➋
• Connect ice transport tube to shuttle actuator ➌

10 remote condensing BIN • TOP-MOUNT
Connect utilities to louvered docking assembly. 6
External connections
➋
➊
• Remove access panel if necessary.
• Install drain line ➊.
The rigid drain line from the ice machine
must have at least 1/4" per foot pitch
(6,4mm/0,3m).
• Install ice machine potable water
supply ➋
• Replace access panel
Water and drain
6.1