Signature Hardware ROTUNDA User manual

1Rotunda Wall-Mount Faucet Installation Instructions
ROTUNDA WALL-MOUNT FAUCET INSTALLATION
GETTING STARTED
TOOLS AND MATERIALS:
BEFORE YOU BEGIN
We recommend consulting a professional if you are
unfamiliar with installing bathroom fixtures and
plumbing. Signature Hardware accepts no liability for
any damage to the floor, walls, plumbing, or personal
injury during installation.
For the following installation instructions, it is
assumed that any old fixture has been removed and
the main water supply is prepared for faucet installa-
tion.
Unpack and inspect the item for damage. If any
damage is found, contact our Customer Relations
team at 1-866-855-2284.
Ensure that you have gathered all of the required
materials that are needed for the installation.
Plumber’s Tape
Shut off the main water supply where the new faucet
is being installed.
PLANNING
Use the faucet’s PDF specification sheet as a refer-
ence when planning your installation. The specifica-
tion sheet can be found and downloaded from the
product page on our website.
Because the faucet specification
measurements are approximate and slight variations
may occur, we highly recommend performing any
rough-in procedures with the faucet on site.
Drill Thread Sealant
Tape Measure Level Hex Wrench
(provided)
Flathead
Screwdriver Pipe Clamps
SKU(s): 919045

2Rotunda Wall-Mount Faucet Installation Instructions
ROTUNDA WALL-MOUNT FAUCET INSTALLATION
INSTALLATION
1. Prepare for installation by installing wood blocking
between the two studs where the faucet will mount.
Important: Take into consideration the thickness of
your finished wall materials, such as tile, when calculat-
ing measurements.
2. Mount the valve body in its prepared location. Attach
the valve body to the wood blocking using pipe clamps.
Use a level to ensure that the valve is mounted straight.
Important: Leave the protective plastic sleeves on the
valve until your finished wall is completed.
3. Attach your existing water lines to the valve body.
Apply thread sealant or plumber’s tape to the thread-
ed connection to ensure a watertight seal.
4. Once your finished wall has been completed,
remove the protective plastic sleeves from the valve
body.
Wood Blocking
Finished Wall
Apply thread
sealant or
plumber’s tape
Hot Water Line
Cold Water Line

3Rotunda Wall-Mount Faucet Installation Instructions
ROTUNDA WALL-MOUNT FAUCET INSTALLATION
5. Slide the decorative escutcheons onto the
installed valve body, as shown.
6. Attach the spout to the valve by threading it into
its outlet, as shown. Apply plumber’s tape or a small
amount of thread sealant to the threads before
attaching.
7. Attach the lever handle by sliding it onto the valve
stem. Remove the screw cover located on the
bottom of the handle, and tighten the set screw to
secure. Reinsert the screw cover.
8. Once installation is complete, turn on the main
water supply. Use the provided tool to remove the
aerator from the spout. Turn the water on to allow any
dust or loose sediment to clear the system. Allow the
water to flow through the spout for approximately 60
seconds, and verify that hot and cold water are
running properly. Reattach the aerator once testing is
complete.
60 sec
Apply thread
sealant or
plumber’s tape
Screw Cover
Set Screw

Rotunda Wall-Mount Faucet Installation Instructions 4
DRAIN INSTALLATION
1. Dissasemble the drain assembly and lay the parts
aside, in the same order they were removed. See the
illustration below as a reference if needed.
2. Apply plumber’s tape to the threading on the
tailpiece, then reattach the tail piece to the pop-up
drain flange.
3. Slide the flat rubber gasket up the tailpiece until it
meets the lip of the pop-up drain flange.
ROTUNDA WALL-MOUNT FAUCET INSTALLATION
Pop-Up Drain Flange
Tailpiece
Flat Rubber Gasket
Tapered Rubber Gasket
Lock Nut
Plastic Friction Washer

Rotunda Wall-Mount Faucet Installation Instructions 5
4. Insert the drain flange and tailpiece through the top
of your sink’s drain hole.
6. Thread the lock nut onto the drain flange. Hand
tighten until secure, then finish tightening with a basin
wrench once the drain is properly aligned.
Important: Be careful not to overtighten, which could
crack a porcelain sink or stone countertop.
5. From under your counter, slide the tapered rubber
gasket followed by the plastic friction washer onto the
tailpiece until they meet your sink or countertop. Be
sure that the tapered side of the rubber washer is
facing up.
COUNTERTOP COUNTERTOP
COUNTERTOP COUNTERTOP
ROTUNDA WALL-MOUNT FAUCET INSTALLATION
COUNTERTOP COUNTERTOP