Formax FD 8850CC User manual

Formax FD 8850CC
Industrial Paper
Shredder
Instruction Manual

FD 8850CC
Industrial Hopper Shredder
OPERATOR MANUAL
12/2011

english
english
03/2011 Powerline 450.2 9
The shredder is exclusively designed for de-
stroying documents, as well as small quantities
of store cards, credit cards, CDs, USB sticks
and 3,5“discs. Its sturdy drive mechanism is not
damaged by paper clips and staples.
The warranty period for the document shredder
is 1 year. The warranty period is 6 months when
used in multiple shifts.
This warranty and guarantee exclude wear and
damage caused by improper handling or ac-
tions taken by third parties.
1 Proper use, warranty Keep paper shredder out of the
reach of children. Do not let the
shredder run if the person using it
is not present.
Switch the shredder off and dis-
connect it from the mains if it is
damaged, not working correctly or
before relocating or cleaning it.
Service work may only be carried
out by Formax Customer Service or
by the service technicians of our
contractual partners.
• Make sure that the mains plug is well acces-
sible.
• Before you insert the mains plug, make sure
that the voltage and frequency of your power
supply comply with the information on the
name plate.
• Make sure that no liquid gets into the shred-
der.
• The shredder may not be placed near a
heater or other heat source.
• The ventilation slots must not be blocked
or covered and there must be at least 5 cm
space between the shredder and any wall or
furniture.
• Read the operating instructions before
switching on the document shredder. Save
these instructions for later use.
• Observe all safety instructions on to the ma-
chine.
Risk of injury!
Do not reach into the paper feed
slot.
Risk of injury from being pulled
in!
Keep long hair, loose articles of
clothing, ties, scarves, jewellery,
etc. away from feed opening.
Material with the tendency to form
loops, e.g. tapes, strapping mate-
rial, etc. must not be shredded.
Risk of injury from slivers!
Put on protective goggles before
you shred hard credit cards, CDs
or f oppy disks.
In emergencies immediately press
the red emergency-stop push-
button! This switches the paper
shredder off.
2 Safety instructions
Translation of the original operating instructions

english
english
10 Powerline 450.2 03/2011
Membrane keyboard
Reversing pushbutton
Cutting system runs in reverse
direction.
Stop pushbutton
Cutting system stops.
Shredder remains in standby
function.
ON pushbutton
Shredder is switched on.
Cutting system runs in feed
direction.
Door or flap opened
red LED
Paper jam – electric motor
overloaded
red LED
Cut material bag full
red LED
Ready for operation
green LED
3 Machine components
Main switch
Turning the main switch 90° in
clockwise direction switches the
machine on.
The main switch can be secured
in the OFF postion with a padlock
Emergency-stop pushbutton
In emergencies immediately press
the red emergency-stop push-
button! This switches the paper
shredder off. The emergency stop
button is unlocked by turning it to
the left.
1 Safety instructions
2 Mains switch
3 Emergency-stop pushbutton
4 Membrane keyboard
5 Paper feed slot
6 Folding tray
7 Front door
8 Name plate
9 Flap
10 Filling drum
11 Drum handle
6
7
4
2
10
3
5
11
9
HSM GmbH + Co. KG
Austrasse 1-9
88699 Frickingen / Germany
8
1
6
7
4
2
5
9
3
HSM GmbH + Co. KG
Austrasse 1-9
88699 Frickingen / Germany
8
1
2 x 15 mm
3,9 x 50 mm

english
english
03/2011 Powerline 450.2 11
Switching the paper shredder on
• Unlock the emergency stop button by
turning it anti-clockwise.
• Turn main switch to position I.
 Green LED lights.
 Paper shredder is ready for opera-
tion (standby)
Notice Safety switches are installed at the
doors. Paper shredder can only be
switched on if the door and the flap are
both closed.
Shreds smooth paper and continuous
paper
Notice The tray can be folded out to hold
stacks of paper or continuous lists.
• Feed paper. See „Tech-
nical data“ for sheet
capacity.
 The shredding pro-
cess is star ted by a
pho to –cell in the paper
feeding opening.
 When the paper fee-
d opening is free again,
the cut ting sy stem au to ma tical ly swit ches off
af ter app rox. 3 sec. and returns to standby.
Notice
The document shredder can also be
started by pressing the green arrow
button:
• Press briefly:
Cutting device starts.
Automatic stop approx. 3 seconds af-
ter the last piece of paper was drawn
in, or manual stop when the stop but-
ton is pressed.
• Hold down for longer than 2 sec-
onds:
constant operation without light bar-
rier function.
The cutting device runs until it is
switched off with the stop button.
4 Operation
Only machines with cut size 3.9 x 50 mm:
Shredding crumpled paper
• Pull the drum handle
forward and put the
crumpled paper in the
drum.
• Press the green arrow key
.
When you push back the handle the
paper falls into the shredder blades.
Switching paper shredder off
• Turn main switch to position 0
Secure main switch with a padlock, if
necessary.
Destroying USB sticks
Insert USB sticks in the centre of the paper
feed.

english
english
12 Powerline 450.2 03/2011
Paper jam
You have fed in too much paper.
 Paper shredder jammed.
 Red LED in the key pad f ashes.
 Paper shredder reverses automati-
cally.
Notice! Do not press dashed arrow button and
green arrow button alternately for-
wards and backwards.
Cutting unit can be damaged.
CAUTION!
Injuries by cutting rollers are possible
even when the paper shredder is idle.
Keep hands away from the cutting
system!
• Open the f ap and clear the paper
jam.
If material is not completely pushed
out, then
• Close the f ap again.
• Press dashed arrow button.
 Paper is pushed out.
• Pull paper out.
• Separate paper stack and feed paper
again.
• The shredding process is started
again with the green arrow button or
by the light barrier (paper feed).
Electric motor overheated
 Red LED on membrane keyboard
lights.
 Paper shredder switches off auto-
matically.
• Allow paper shredder to cool down
for approx. 15 to 20 min.
Front door or flap opened
 Red LED on membrane keyboard
lights.
 Paper shredder stops automatically.
•
Close door and f ap.
Note If the door is opened when the cut-
ting device is running, the document
shredder must be started again using
the green button after the door of the
document shredder has been closed.
Bag for shredded material full
 Red LED on membrane keyboard
lights.
 Paper shredder stops automatically.
Note Reversing the cutting device (“Re-
verse” button) is also possible even
when the shredded material container
is full.
• Insert new bag.
Notice! Empty the shredded material con-
tainer after the paper shredder has
been switched off, because otherwise
malfunctions of the cutting system
could occur when the rocker switch is
pressed several times in succession.
5 Troubleshooting

english
english
03/2011 Powerline 450.2 13
Switch off the shredder and pull out the mains
plug. When cleaning only use a soft cloth and
a mild soap-water solution. However, no water
must enter the equipment.
Oil the cutting unit when
cutting performance de-
creases or the device be-
comes noisy, or every time
you empty the waste con-
tainer:
6 Cleaning and maintenance • Spray special cutting block oil
through paper feed opening across
the whole width of the cutting system
blades.
• Run cutting system forwards and
backwards several times without
feeding paper.
 Paper dust and particles are shaken
off.
7 Technical data
EU-Version
US-Version
Cutting type Cross cut
Shred size (mm) 3.9 x 50
Nominal cutting capacity, DIN A4 70 g/m260 sheets
Cutting speed 218 mm/s
Loading width 443 mm
Power supply 3W + PE 208 V, 60 Hz
Rated power 2.99 HP
Nominal current 20 A
Plug L15-30P 30 A
Ambient air temperature 25 °C
Dimensions W x D x H (mm) 750 x 665 x 1590
Weight 220 kg
Volume of shredded material bag 290 l
Noise level (Idle running/ load) 58 dB(A) / 70-75 dB(A)
Cutting type Cross cut
Shred size (mm) 3.9 x 50 2 x 15
Safety rating DIN 32757 – 1 3 4
Cutting capacity (sheets), DIN A4 70 g/m2
80 g/m2
80 - 85
65 - 70
35 - 40
28 - 32
Cutting speed 218 mm/s
Loading width 443 mm
Weight 220 kg
Volume of shredded material bag 290 l
Noise level (Idle running/ load) 58 dB(A) / 70-75 dB(A)
Dimensions W x D x H (mm) 750 x 665 x 1590 750 x 665 x 1460
Power for the maximum number of sheets 3 kW 2.2 kW
Power supply
Power supply fuses (slow-blow)
3 x 400 V, 50 Hz
3 x 16 A
3 x 400 V, 50 Hz
3 x 10 A