ForPro Classic Hot Towel Warmer User manual

Replacing the Bulb continued
8. On the right side of the box, you can see two screws, screw out the two screws and open
the small cover of the box. See Fig. 5a & 5b.
9. Remove the faulty bulb. Insert a new bulb (Replacement bulb Item #391445) back inside the
small box, close the lid, and tighten the two screws on the lid. See Fig. 6a & 6b.
10. Reattach both lines and tighten the screws of the box. See Fig. 7a & 7b.
11. Replace environmentally friendly cotton and reattach back panel.
Classic Hot Towel Warmer
Item #303406 • New Hudson, MI 48165
www.tngworldwide.com • 800.520.6000
Made in China • ©2022 TNG
Troubleshooting
1. There is excessive moisture when the towel warmer is ON or the towels are heating up very
slowly.
• Check to see that the towels are only slightly damp. Excess moisture and/or slow heating
time may be a result of soaked towels.
2. The door is not closing properly and/or steam is escaping
• Check that the silicone door seal is in place. Push into door groove to assure proper fit.
Safety Precautions
Caution and proper procedures must be practiced at all times when using electrical appliances.
Basic safety precautions should always be followed, including the following:
• Do not use appliance for other than intended use.
• Do not place poisonous, flammable, explosive and evaporative chemicals into the towel
warmer.
• Do not touch hot surfaces. Use handle or knobs.
• To protect against electrical shock, do not immerse cord, plugs or appliance in water or
other liquid.
• Unplug from outlet when not in use and before cleaning. Cool the machine before
maintenance.
• Do not operate any appliance with a damaged cord or plug or after the appliance
malfunctions or has been damaged in any manner. If the product is defective, stop using it at
once and contact supplier for service.
• Do not use outdoors. This appliance is intended for indoor use only.
• Do not let cord hang over edge of table or counter, or touch hot surfaces.
• Close supervision is necessary when any appliance is used by or near children.
• Do not leave the appliance unattended when switched on.
• Extreme caution must be used when moving an appliance containing hot liquids.
• The temperature of accessible surfaces may be high when the appliance is operating.
• If using an extension cord, the marked electrical rating of the extension cord should be at
least as great as the electrical rating of the appliance.
Internal surfaces, wire baskets, towels and steam may be hot. Use with extreme caution
when removing hot towels or baskets. Always use protective heat-resistant gloves or
mitts to avoid steam or other burns. Ignoring the warnings may result in harm or serious
injury.
Classic
Hot Towel Warmer
8. Tighten the screws of the UV box
9. Install environmentally friendly cotton and backboard
8. Tighten the screws of the UV box
9. Install environmentally friendly cotton and backboard
Fig. 5a
Fig. 6a
Fig. 5b
Fig. 6b
Fig. 7a Fig. 7b
IMPORTANT INSTRUCTIONS — RETAIN FOR FUTURE USE

Classic Hot Towel Warmer Operation Manual
Congratulations on your purchase of the ForPro Classic Hot Towel Warmer. Please read
the instructions and safety tips before use. Your Hot Towel Warmer comes with a one-year
unlimited warranty. If for any reason you need service, please call 800-520-6000.
Product Specification
Rated Volume: 23L
Rated Power: 200W
Rated Voltage: 110V
Rated Frequency: 60Hz
Set Temperature: 180°F
Towel Load: 24 Facial-Sized Towels
External Dimensions: 17.75”W x 11”D x 14”H
Inside Dimensions: 14.5”W x 7.5”D x 9.75”H
EPA-registered
UV sterilization: EPA #99360-CHN-1
Components
Before Operation
• Be sure to remove all packing material before use.
• Place the unit on a well ventilated, flat, sturdy surface away from heat sources. The unit should
not be used in the immediate vicinity of water (such as bathtub, washbowls, etc.) where the
likelihood of immersion may occur. Keep at least 30mm away from walls and other objects.
• Plug cord into a 110V power outlet.
• Remove the wire basket and set aside.
Operation
1. Please fold or roll up the damp or pre-moistened towels but not soaked ones into the wire basket
of hot towel warmer. Try to wring out the water several times to shorten the heating time.
2. The inside wall temperature is up to 180°F. 100% cotton dry towels could be put as well but
not any other cloths which couldn’t bear this high temperature, and keep it within less than 2
hours heating. Please keep the towel away from the inner wall of warmer.
3. Do not overload the wire basket or directly place towels into the towel warmer.
4. Close the door firmly and press the Power button to turn on. The indicator near the switch
will be on to show that the towel cabinet has started heating.
5. In about 1.5--2.5 hours, depending on how many towels you put inside, while keeping the
door closed, the temperature inside the cabinet will heat up to approximately 180°F and will
be kept automatically. Avoid opening cabinet when towels are heated.
6. Turn off the power button whenever you want to add more towels. The heating process will
be restarted. The thermostat will automatically stop working when temperature reaches up
to 180°F. It’s safe to keep it on.
7. If desired, press the UV button to turn on EPA-registered UV sterilization system. The
indicator near the switch will be on to show that the UV light is working. Wait 30 minutes for
the sterilization process to complete.
8. Whenever you want to open the door, please firstly turn off the power with the indicator
light off. Stay a safe distance from cabinet door opening to avoid being burned by high
temperature steam from the cabinet. Remove towels with tongs or heat resistant gloves.
9. Towels may be too hot to apply immediately, and caution should be used before applying
to the face or body.
Maintenance
1. Turn OFF the unit.
2. Unplug the cord from the outlet.
3. Wait for contents to cool before handling. Contents may be hot. Remove the wire basket
and towels. Set the wire basket aside to dry.
4. With a soft cloth, wipe down the internal surfaces. Do not use harsh chemicals or abrasives.
To clean exterior, use a soft cloth and mild soap.
5. Pull the drip tray forward and empty contents. Set the drip tray aside to dry.
Replacing the Bulb
1. Turn OFF the unit.
2. Unplug the cord from the outlet.
3. Remove all the screws on the back panel
and open the back panel.
4. You can see the white cotton after opening
the back panel. See Fig. 1.
5. Take out the white cotton back, you can see
the position of the lamp. See Fig. 2.
6. Unplug both lines. See Fig. 3.
7. Loosen the screws on the small box (the screws are connected to the inside of the liner and
can be screwed out from the inside of the liner). See Fig. 4a & 4b.
Power
Indicator Light
UV Light Switch
Power Switch
UV Light Indicator
Wire baskets
Water Drip Tray
Cabinet Leg Cabinet Door
See
Through
Window
Fig. 1
Fig. 2
Fig. 3
Fig. 4a Fig. 4b