Forward Industries JWKJ3002-F Manual

Ottoman Storage Bed
(Full / Queen)
Care & Instruction Manual
Please read and retain these instructions for future
reference
STOCK CODES : JWKJ3002-F (Full)
: JWKJ3002-Q (Queen)
IMPORTED BY FORWARD INDUSTRIES, 33401, USA
Issue 1 - 03/09/20

2
Safety and Care Advice
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
This product has been
constructed to be used in the
domestic environment only and
not for commercial purposes.
Care and maintenance
Only clean using a damp cloth
and mild detergent. Do not use
abrasive cleaners.
Use a dry cloth to clean the
product, furniture polish is
not recommended.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
We do not
recommend the
use of power
drill/drivers for
inserting screws
as this could damage the unit.
Only use hand screwdrivers.
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging
carefully and responsibly.
From time to time check that there
are no loose screws, nuts or bolts.
If there are please re-tighten.
This product should not be
discarded with household
waste.Take to your local
authority waste disposal
centre.
Important Ottoman Safety Warnings
Caution.This bed uses a pressurised mechanism.
Use caution when operating - Always use two hands at arm’s length, and only where illustrated on the
product.
You must ensure the mattress is on the bed frame before lifting the mechanism - Failure to do so may
result in injury.
Please ensure Children and pets are kept away from the bed when operating the bed mechanism.
If removing the mattress, make sure that the frame is secured as it could flip open.
Only use the storage compartment when when the frame is fully raised in the ‘up’ position.
No children or animals are left unattended when the frame is in the ‘up’ position.
Do not remain on the bed whilst the lifting mechanism is in use.
Beware of Entrapment - Keep both hands clear of mechanism when operating the mechanism.
When lifting the bed remove all bedding - Except the fitted sheet.
ENSURE MATTRESS IS ON
BEFORE LIFTING
DON'T LIFT WITHOUT MATTRESS

Please check you have all the parts listed below
Main Components
3
1
3 4
5 6
7 8
910
INSIDE INSIDE
INSIDE
INSIDE
Side Rail (Right) Headboard End
(4'6-38 × 12.5in)(5'-40.1 × 12.5in)
Side Rail (Left) Headboard End
(4'6-38 × 12.5in)(5'-40.1 × 12.5in)
Headboard (4'6-57 × 38.9in)
(5'-63 × 38.9in)
Footboard (4'6-57 × 12in)
(5'-63 × 12in)
Hinge Mechanism (x 1 pair)
NOTE: PISTON ATTACHED
Fabric base x 1 (4'6-77.1 ×55.9in)
(5'-81.5 × 61.8in)
Ottoman end frame (Headboard) x 1
(4'6-53.6 × 3.3in)(5'-59.5 × 3.3in)
NOTE: EXTRA HOLES
Ottoman end frame (Footboard) x 1
(4'6-53.6 × 3.3in)(5'-59.5 × 3.3in)
Ottoman frame centre support
Headboard End x 1
(4'6/5'-35.2 x 1.1in)
NOTE: EXTRA HOLES
2
INSIDE
INSIDE
11 12 Ottoman frame centre support
Footboard End x 1
(4'6/5'-40.3 x 1.1in)
Side Rail (Right) Footboard End
(4'6-38 × 12.5in)(5'-40.1 × 12.5in)
Side Rail (Left) Footboard End
(4'6-38 × 12.5in)(5'-40.1 × 12.5in)
For missing or damaged parts, call our Customer Helpline: [phone], option 0. or
email [email protected].
.

Double slat caps x 14 (4'6-2.16in)
Double slat caps x 15 (5'-2.16in)
Single slat caps x 28 (4'6-2.16in)
Single slat caps x 30 (5'-2.16in)
Bentwood slats x 28 (4'6-26.5 x 0.35 x 2in)
Bentwood slats x 30 (5'-29.5 x 0.35 x 2in)
13
Mattress support bracket x 2
Stretcher x 1 (4'6-54.7 × 0.98in)
(5'-60.8 × 0.98in)
Ottoman frame (Sides Left)
Headboard End x 1
(4'6/5'-40.3 x 1.1in)
NOTE: EXTRA HOLES
Ottoman frame (Sides Left)
Footboard End x 1
(4'6/5'-35.2 x 1.1in)
Ottoman frame (Sides Right)
Headboard End x 1
(4'6/5'-40.3 x 1.1in)
NOTE: EXTRA HOLES
Ottoman frame (Sides Right) x 1
Footboard End x 1
(4'6/5'-35.2 x 1.1in)
Connecting Bracket
(Ottoman Frame Sides) x 2
(11 x 1.1 x 1.1in)
Ottoman frame support x 1
(5.11 × 1.18in)
Support Leg (U Shape) x 1 (0.98 × 7.87in)
Support Leg (Flat) x 1 (0.98 × 7.87in) Foot x 4 (∅0.13 × 0.59in)
Connecting Plate (Side Rails) x 4
(1.57 × 3.54in)
14
15 16
17 18
19 20
21 22
23 24
25 26
27
Please check you have all the parts listed below
Main Components
4
For missing or damaged parts, call our Customer Helpline: [phone], option 0. or
email [email protected].
.

Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
M8 Nut Qty 6
BC
D E F
(0.66in) M8 Flat washer Qty 66
A
F
G
(1.77in) M8 Bolt Qty 8
(0.47in) M8 Spring washer Qty 32 M5 Allen key Qty 1
Spanner Qty 1
H
(1.18in) M4 Screws Qty 4
Fixings, Fittings And Tools
5
J
(1.18in) M8 Bolt Qty 22(0.98in) M8 Bolt Qty 36
(1.77in) M4 Screws Qty 4
Box spanner Qty 1
K L
For missing or damaged parts, call our Customer Helpline: [phone], option 0. or
email [email protected].
.

Step 1
Step 2
B
F
G
B
C
F
23
2
C
F
2
1
23
F
G
Leave screws loose
Ensure surface is protected to
prevent marking.
Prepare headboard
and Footboard.
Assemble support.
BGF
J
CFJ
x 12 x 12 x 12
x 2 x 2 x 1
Assembly Steps
6

Step 4
Assembly Steps
Footboard End
7
Step 3
Do not fully tighten fixings!
Holes at
headboard end
3
4
5
6
1
2
1
3
3
4
5
6
F
G
A
27
Loosely assemble bed
frame.
Two people will be
required.
Headboard End
AGFx 8 x 8 x 8 Jx 1
J
Two people required
Connect side rails using
connecting plates 27 .
Repeat for both side rails.
J
Jx 1
F
G
A
4
327

Step 6
Assembly Steps
8
Step 5
17
17
E
8
E
Two people required
Ensure frame is square
Assemble stretcher.
Ensure frame is square.
Tighten all fixings before
proceeding to step 6.
Fit fabric base using velcro
strips.
Two people required to
carefully turn the frame.
Ex 4

9
Assembly Steps
26
D
BF
26
D
B
F
7
7
Step 7
Step 8
Assemble feet.
NOTE: Pistons are
pre-assembled
Assemble ottoman hinge
mechanisms.
The hinges will move.
Beware of entrapment!
Dx 4
J
B F J x 10 x 10 x 1

Assembly Steps
10
Shown upside down
Shown upside down
F
A
F
A
F
A
F
A
24
25
24
25
11
12
12
11
11
F
A
F
A
19
19
13
14
15
16
A
F
Holes on inside
13
14
Step 9
Step 10
Assemble ottoman frame
sides.
Assemble ottoman frame
centre support and legs.
Support legs 24 and 25
are different.
Headboard End
FJ x 4 x 1Ax 4
J
J
J
FJ x 8 x 1Ax 8
extra holes
headboard end
AF
19

11
Assembly Steps
Holes at
headboard end
Holes at
headboard end
Legs this
end
Headboard end
Extra holes
Footboard end
Shown upside down
Headboard end
A
F
18
A
F
9
10
18
F
G
A
F
G
A
9
10
13
14
15
16
11
12
Step 12
Step 11
J
J
Complete ottoman frame
assembly.
Turn ottoman frame over
and assemble mattress
support brackets.
Two people will be
required.
AGFx 12 x 12 x12 Jx 1
FJ x 4 x 1Ax 4
Two people required

12
Assembly Steps
UP
Beware of risk of entrapment
from folding hinges!
Important: Two people required.
Frame to be fully supported at
all times!
Ensure frame is square
Nut pre-assembled
9
10
3F
C
H
15
3
6
3
7
Step 14
Step 13
J
Two people required
K
CFx 6 x 6 Jx 1 Kx 1Hx 6
Connect the pistons.
The frame must be
fully supported at all times.
Two people will be
required.
C
F
Ensure the bed frame is
square.
With help, assemble
ottoman frame to hinge
mechanisms.
The mechanisms will
move. Beware of
entrapment.
Kx 1
H

Fit plastic slat caps and
bentwood slats.
Ensure slat caps are
properly engaged into
the holes.
13
Assembly Steps
a:
b:
20
22
c:
12
21
20
Slats to arch upwards
22
20
22
22
22
22
20
20
21 20
20
21
3 45 6
11 12
Step 15
12

14
lf you have questions regarding the operation of your purchase, or in the unlikely event you need to return the
unit because it is faulty or is no longer wanted, please contact our product returns department at
[email protected], or 561-465-0030,Option 0.
Address: Forward Industries,105 South Narcissus Avenue Suite 412, West Palm Beach, FL 33401
After Sales Support / Product Returns