Hay NEW ORDER User manual

– INSTRUCTION MANUAL –
DESIGN BY STEFAN DIEZ
TABLE GROUP 6
NEW ORDER

TABLES
TABLE OVERVIEW
PARTS OVERVIEW
TABLE ASSEMBLY INSTRUCTIONS
CONNECTORS
TABLE WALL CONNECTOR INSTRUCTIONS
FRONT SHELF CONNECTOR INSTRUCTIONS
END SHELF CONNECTOR INSTRUCTIONS
END TRAY CONNECTOR INSTRUCTIONS
CABLE MANAGEMENT
CABLE TRAY INSTRUCTIONS
CABLE CLIP INSTRUCTIONS
CABLE GUIDE INSTRUCTIONS
PLUG SOCKET
WALL MOUNTING GUIDELINE
CARE & MAINTENANCE
 TABLE OF CONTENTS 
5
67
822
2326
2730
3134
3537
3840
4142
4344
4548
49
50

4
 TABLE OVERVIEW 

5
150x150
150x150
150x150
  
TABLE

7Q
  
TABLE

7R
  
TABLE

7S
It is important to start by identifying your table model to ensure you follow
the correct assembly instructions.
 TABLE OVERVIEW 

6
  
TABLE

7Q
  
TABLE

7R
  
TABLE

7S
TABLE
PART
x3
x3
x3
x2 x1
x1
x1
x2
x2
—
—
—x2
—
x2
x4
x4
x4
x4
x4
x4
x4
x4
x4
x4
x4
x4

ACorner knot*

BFrame profile

CLeg**

DTabletop

ESupport bar

FExtra support bar

IScreen

GTray

HSingle profile
*Quantity of corner knots and legs depends on your table configuration.
**Only for high tables with footrest.
 PARTS 

7
x1
x1
x1 x2
—
x2

JScreen mount

KScreen mount
—
—
—
—
x2
x2
x2
x2
x2

MCable management
BAG BAG BAG BAG BAG

3 Supportbar

4 Frame

5 Tabletop

6 Legs

12 Screen

3  4  5  6  12
x1
x1
x1
x2
x2
x2
x1
x1
x1
x3
x3
x3

11 Tray divider
BAG

11
 PARTS 

8
SB
(SUPPORT BAR)
ESB
(EXTRA SUPPORT BAR)
 INFORMATION ON SUPPORT BARS 
0 1 45 6123 2 3456
SB
SB
ESB
ESB
New Order tables uses two support bars to reinforce the construction.
The two different types are 'Support bar' (SB) and 'Extra support bar' (ESB)
The small dotted markings on the table frame should align with the marking
on the support bar/extra support bar connector.
The markings on the table frame are not numbered, but counting from the
center mark (0) will guide you to the correct position for your support bar.

9
 INFORMATION ON SUPPORT BARS   SUPPORT BAR POSITIONS 
6 5 4 3 2 1 0 1 2 3 4 5 6
0 1 45 6123 2 3456
TABLE
POSITION
FRAME PROFILE 150 CM
  
TABLE

7Q
  
TABLE

7R
  
TABLE

7S

10
  
3A x2
x2
BAG

3
  
3B x1
  
3C x4 Connector is
delivered with the
support bar

E.
FIND THE CORRECT
POSITION IN THE
OVERVIEW ON PAGE 8
8
1.
Insert the brackets
  
3A into the two shortest table frame profiles

B. Then mount the
ESB connectors
  
2D and the SB connectors found in support bar  Eon both frame
profiles and fasten them with screws
  
3C using tool 
 
3B . Make sure to find the
correct position on page 8, before tigthening screws completely.

11
2.
Insert the corner knots

A into the two table frame profiles from step 1.
Then connect them with the other two profiles

B to close the frame.
Place the support bars

Ein between.

12
3.
Secure the frame with screws
  
4B using tool
  
4A in each corner.
  
4B x32
  
4A x1
BAG

4

13
4.
Fasten the support bar

Eand extra support bar  F with screws
  
3A using tool 
 
3B .
  
3C x4
  
3B x1
BAG

3

14
5.
Connect the legs

C by threading them onto the tap of the corner knot.
Secure with screws
  
6B using tool
  
6A .
  
6B x4
  
6A x1
BAG

6

15
Mount the profile connectors
  
11A with screws 
 
11B using an Allen key in the
table top  Dwith holes in the corners.
6.
  
11B x4
  
11A x4
BAG

11

16
Mount screen holder

L.
Secure with screws 
 
12A with screen  I ..
Placement of screens depends on your table model.
BAG

12
  
12A x4
Screen holders are
delivered inside
the screens.
SEE POSITION OF
SCREENS IN TABLE
OVERVIEW ON PAGE 4
4
7.
ONLY FOR TABLES 7R, 7S

17
8.
Place the tabletops

D . Start with the outer two and then the middle one.
Then place the cable covers

M in between the tabletops.

18
9.
Fasten the tabletop

D with the clips
  
5B from underneath. Distrubute the clips evenly.
Secure them with screws
  
5C using tool
  
5A .
  
5C x10
  
5A x1
  
5B x10
BAG

5

19
10.
Place profiles

Hon the fittings on the middle tabletop. Then mount the tray

G on
top of the profiles.

20
11.
Secure the profiles by tightening the set screws, both in top and bottom, on all profiles.