Regalo 1350B User manual

www.regalo-baby.com
Regalo International, LLC.
3200 Corporate Center Drive, Suite 100 / Burnsville, MN 55306, USA
866.272.5274 (U.S. only) or 952.435.1080
Made in China
4-in-1 Play Yard
Safety Gate
OWNER’S MANUAL MODEL: 1350, 1350B
• READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE.
• KEEP INSTRUCTIONS FOR FUTURE USE.

English 3
Before Using Product
Read and follow all instructions carefully to ensure that your gate and extensions are
properly installed. Improper installation could result in the gate becoming unstable or
dislodged from the doorway. Always make sure the extension is securely attached
to the gate before using. The safety of your child is your responsibility. Please keep
these instructions for your reference.
IMPORTANT
• The four mounting brackets must be used in securing the gate to the wall.
These brackets prevent the gate from dislodging from its opening and
becoming unstable.
• If hardware mounting to a surface other than drywall or wood, please
consult with a professional about installation.
• The maximum width of this gate is 192 inches.

English4
WARNING
• Install according to manufacturer's instructions.
• Children have died or been seriously injured
when gates are not securely installed. ALWAYS
install and use gate as directed using all required
parts.
• STOP using when a child can climb over or
dislodge the gate.
• Use only with the locking/latching mechanism
securely engaged.
• To prevent falls, never use at top of stairs.
• NEVER use to keep child away from pool.
• Intended for use with children from 6 months
through 24 months.
• This product will not necessarily prevent all
accidents. Never leave child unattended.
•Always ensure the gate is resting against the floor
before beginning installation.
• Check the gate regularly to see if all the hardware
and mountings are tightened.
• Do not use if any components are missing or
damaged.

A
C
B
English 5
PLEASE CHECK TO MAKE SURE YOU HAVE THE FOLLOWING PARTS:
A Play Yard Gate Frame (8 Panels)
B Plastic Mounting Brackets (4 – Attached to Gate Frame)
C 1" Wall Mounting Screws (8) (requires a Phillips/cross-head screwdriver)
Before Assembly

English6
STEP 1
Unfold the gate frame by turning the locking knobs counter clockwise at each
pivoting joint. Loosen the knobs enough to allow the gate to swing open freely
without fully removing the knobs.
Option A: Installing Your Gate Between Two Walls
LOCKING KNOB
STEP 2
Use a Phillips/crosshead screwdriver to fix the wall mounting bracket to the
wall. Repeat for all four brackets.

English 7
STEP 3
Arrange the panels to your desired configuration, then tighten all of the
locking knobs.
NOTE: This gate is designed to fit minimum width openings 51.5 inches wide.
51-1/2" Minimum Width

English8
STEP 1
Unfold the gate frame by turning the locking knobs counter clockwise at
each pivoting joint. Loosen the knobs enough to allow the gate to swing
open freely without fully removing the knobs.
Option B: Installing Your Gate as a Freestanding Enclosure
STEP 2
Release the vertical metal pivot bars at each end of the play yard by
removing the following parts from the assembly:
TOOTHED DISK (1 )
LOCKING KNOB (2)
WALL MOUNT BRACKET (2)
WALL MOUNT BOTTOM
CAP – MALE (1)
WALL MOUNT BOTTOM
CAP – FEMALE (1)
METAL PIVOT BAR (2)
TOOTHED CAP (1)

English 9
STEP 3
Position the play yard into your desired configuration (e.g. octagon, square),
then join the free ends of the play yard together at the plastic joints.
STEP 4
Insert one of the previously removed metal pivot bars between the upper
plastic joints and the lower plastic joints.
A
B
A
B

English10
STEP 5
Tighten the locking knob on the metal pivot bar by turning it counterclockwise.
STEP 6
Tighten each of the remaining
locking knobs by turning them
clockwise, fixing the play yard
into the configuration you have
chosen. To position the play
yard into a new configuration
or shape, simply loosen each
of the locking knobs, adjust
and retighten.
NOTE: When adding or removing additional panel units to the
configuration, panels must be added or subtracted in sets of two for the
freestanding enclosure to function properly.
B
B

English 11
STEP 1
Pull both sides of the slide lock sideways away from the metal lift latch while
simultaneously pivoting the metal lift latch upward from the gate’s door frame.
STEP 2
To relock the gate, close the door completely and drop the metal lift latch back
into place. The slide lock will return to it’s locked position on its own.
Operating the Door Latch
SLIDE LOCKMETAL LIFT LATCH

English12
TO FOLD YOUR PLAY GATE
STEP 1: Loosen all of the locking knobs so the play yard can move freely
and becomes flexible at the joints.
STEP 2: Remove one of the vertical tubes from the play yard.
STEP 3: You will now be able to pull the two plastic joints and the top and bottom
of the play yard apart.
STEP 4: Fold and put away.
CARE AND MAINTENANCE
Periodically check the gate for signs of damage, wear, or missing components.
Do not use if any part is missing, worn or damaged. Check the gate regularly to
ensure all the hardware and mountings are tightened. Do not use abrasive
cleaners or bleach. Clean by sponging with warm water and a mild detergent.
90 DAYS LIMITED WARRANTY
If, during the first 90 days after consumer purchase of the item, under reasonable
and non-commercial use and conditions of maintenance, it fails while owned by
the original purchaser because of the quality of materials or workmanship of finish
and assembly, Regalo International, LLC, will replace or repair it at Regalo’s option.
PROOF OF PURCHASE REQUIRED.

English 13
Replacement Parts
A Door Frame Toothed Hinge
White = #300776-001
Black = #300776-002
B Top Hinge
White = #300779-001
Black = #300779-002
C Toothed Hinge
White = #300781-001
Black = #300781-002
D Locking Knob
White = #300778-001
Black = #300778-002
E Wall Mount Bracket
White = #300638-001
Black = #300638-002
F Wall Mount Bottom
Cap – Male
White = #300613-001
Black = #300613-002
G Bottom Hinge – Female
White = #300325-001
Black = #300325-002
H Door Frame Bottom Hinge
White = #300306-001
Black = #300306-002
IBottom Hinge – Male
White = #300322-001
Black = #300322-002
JWall Mount Bottom
Cap – Female
White = #300612-001
Black = #300612-002
K 1" Wall Mount Screws
L 27" Metal Pivot Bar
White = #300804-001
Black = #300804-002
M Wall Mount Toothed Disk
White = #300782-001
Black = #300782-002
N Toothed Disk
White = #300783-001
Black = #300783-002
AB
C
J
K
L
D
E
F
N
M
G
H
I

www.regalo-baby.com
Regalo International, LLC.
3200 Corporate Center Drive, Suite 100
Burnsville, MN 55306, USA
866.272.5274 (U.S. only) or 952.435.1080
20170622EF