FORWODE DB-HBS32 User manual

Model:DB-HBS22 INSTRUCTIONS
PAGE 1
INSTRUCTION
1
Model:DB-HBS32
2-BIKE HITCH-TIGHTENING SYSTEM
TILT-FOLD BICYCLE RACK
Model:DB-HBS32 INSTRUCTIONS
TOOLS
REQUIRED
• Adjustable Wrenches
Or 11/16" & 3/4"
Wrenches
• Phillips Screwdriver

ABottom tube
Vertical tube
Cross tube assembly
Fixed bend tube assembly 1
Fixed bend tube assembly 2
Wheel fixing straps
Fixed hook 1 assembly
Fixed hook 2 assembly
Half tooth carriage bolt M12
ITEM NO. DESCRIPTION
B
C
D1
D2
E
G1
G2
H
1
1
2
2
2
4
1
1
1
QTY.
Self-collar nut M12
I
J
1
1
2
PRODUCT PARTS CATALOG
A
B
C
X
H
D2
D1
CD1
D2
G2
G1
R
Q
P
V
L
K
J
I
E
T
M
N
O
S
U
A B C
D1 D2 E G1 G2
H I J K L
MN O P
Q R S V W X
TU
KRound with positioning spacer
Square pin
U-connector
Fixing plate
Trailer lock
L
M
N
O
P
Q
R
S
2
1
2
2
2
1
4
1
1
T
U
4
4
V 3
Trailer lock Key
W 2
Cross-rail fixed assembly Key
X 4
W

Remove Lfrom A.
Two pieces of K are loaded into the inside of Ain advance. (The two cylinders of K are inserted
into the two small holes).
Insert Binto the interior of Aand then connect in order with I-J-H fasteners.
Insert Lfrom A into Band fasten.
STEP 1:
3
INSTALLATION STEPS
H I J K
L
L
A
I,J,H
B
L
STEP 2:
Insert Cinto figure B, the 4 holes on the side are
connected with 4 sets of standard parts S-T-U
locking respectively（Install the two inner holes
first and then the outermost hole）.
STEP 3:
Insert D1 and D2 into figure C, respectively, and
lock the connection with their own hand screw
nuts.
C
B
S,T,U
S T U
D1 D2
C
K

Disassemble the Rremove O-M-N with the
handle and remove P-Q and put it away.
Disassemble the R .
Pull out from the trailer bar .
4
R
DISASSEMBLY STEPS
B
STEP 4:
Insert the G1 and G2 components into the upper
square opening of the assembled bike frame B,
Use the key Xto position the sliding position,
adjust to suitable position, lock G1 G2 with key X.
STEP 5:
G2 XG1
Insert the Vat the place marked by the arrow
above, and tighten it with a screwdriver.
Q
N
M
O
P
STEP 6:
Insert Rinto the tariler bar.
Lock the trailer lock (R) with the key (W) and keep
the key
Pass P,Qthrough O,M,N and lock them with
V
V
W
R
Q
N
M
O
P

Press the column slightly to the left, while pressing
the pop-up buckle as shown, and fold the column
to the right.
Press the downed column slightly downward,
while pressing the pop-up buckle as shown in the
picture, and lift the column to the left.
RACK FOLDING STEPS
Pop-up buckle
Pop-up buckle
STEP 1: STEP 2:
•Hold with your left hand
and pull it outward slightly.
•Squeeze tightly with the
right hand and tighten.
•Loosen .
•Pull out and rotate
•Insert and rotate the
handle clockwise until
tightened.
•Pull out with force
and rotate back to the
initial state to tighten again.
•Disassembly steps refer to
tightening steps.
TIGHTEN THE HANDLE
Fine-tuning preload knob
a
Handle head
b
Positioning pins
d
Handle grip
c
b
b
a
d
d
c
b c
Light Press
Fold to Right Up Wards
Light Press

GENERAL CONSIDERATIONS WARNING WHEN INSTALLING THE FRAME
1.Every month new designs and bodies are introduced
to the market.
2.While the FORWODE bike carrier design team strives
to make most products universal to the cars on the
market. It is impossible for a single bike carrier to fit all
models of cars on the market.
3.Before you purchase a rack, please check if the rack
fits your vehicle with an authorized FORWODE Bike
Rack dealer or distributor.
4.Before installation, please read the instructions and
then follow the attached instructions.
preset and in working condition. For any missing or
damaged parts, please contact your authorized FOR-
WODE Bike Rack dealer or distributor.
6.Please always keep this manual for future reference.
1. When the vehicle is equipped with an electric
rear fender, the power must be turned off when
installing the rear carrier. If this option is not
available, do not use the rear bike carrier.
2. Clean the receiver connector thoroughly
before installing.
3. When the vehicle is equipped with a spoiler or
similar item, it is necessary to change the
mounting method of the bike carrier. If this
happens, please contact an authorized FOR-
WODE bike carrier verifying dealer or distributor.
4. When using the bike carrier, please observe
local traffic laws.
before washing your bike.
6
Pull out the Land put it down.
Pull out the L-square pin and rotate the frame by
L
RACK TILT STEPS
L
STEP 3:

7
WARNING WHEN MOUNTING THE BICYCLE WARRANTY AND LIABILITY
1. When you ride your bicycle, make sure that it does not
touch the vehicle, especially the pedals. Using protective
foam pads may be helpful.
2. Remove all loose items before mounting the bike. For
example, water bottles.
3. Bicycle tires must be kept away from vehicle exhaust
fumes.
maximum per bicycle) and the capacity of the bicycle,
according to the manufacturer's recommendations.
behavior for vehicles. Use extreme caution when driving in
high winds, sharp turns and on rough roads. Drive slowly
6. Vehicles with bike racks installed have extra width and
length. Also, make sure that the bicycle is mounted in the
middle to avoid excessive protrusion.
7. When the vehicle is equipped with a bicycle rack, check
the installation of the rack and the installation of the bicycle
ensure the safety of passengers and others!
1.FORWODE does not bother to assume
any liability for any damages (to the vehicle,
damage caused by incorrect installation and
use of this product or its accessories, goods
and/or persons in connection with the
purchase, use or handling of this product).
2.If you have further questions about our
limited lifetime warranty or need any support,
you can start a conversation with us at
[email protected].
FORWODEBIKE
Forwode Bike Forwode Bike
[e-mail]