Circutor ePARK M-S2 User manual

ePARK
INSTALLATION GUIDE
(M262A01-03-23A)

ePARK
2Installation guide

ePARK
3Installation guide
Disclaimer
Disclaimer
CIRCUTOR S.A.U. reserves the right to make modifications to the device or the unit specifications set
out in this instruction manual without prior notice.
CIRCUTOR S.A.U. on its web site, supplies its customers with the latest versions of the device speci-
fications and the most updated manuals.
www.circutor.com
Revision log
Date Revision Description
06/19 M262A01-03-19A Initial Version
11/19 M262A01-03-19B Changes in the following sections:
1.- 2.- 3.- 4.- 5.- 5.A.- 5.B.- 5.E.- 5.F.- 6.
09/20 M262A01-03-20A Changes in the following sections:
6.
04/21 M262A01-03-21A Changes in the following sections:
2.1.- 5.F.- 6.
06/21 M262A01-03-21B Changes in the following sections:
5.E.- 6.
10/21 M262A01-03-21C Changes in the following sections:
4.- 6.
10/21 M262A01-03-21D Changes in the following sections:
6.
07/23 M262A01-03-23A Changes in the following sections:
1.- 2.B.- 3.- 5.B.- 5.E.- 5.J.- 6.

ePARK
4Installation guide
ePARK
Installation guide
COPYRIGHT INFORMATION
This document is copyrighted, 2023 by CIRCUTOR S.A.U. All rights are reserved. CIRCUTOR S.A.U.
reserves the right to make improvements to the products described in this manual at any time
without notice.
No part of this manual can be reproduced, copied, translated or transmitted in any form or by any
means without the prior written permission of the original manufacturer. Information provided in
this manual is intended to be accurate and reliable. However, the original manufacturer assumes no
responsibility for its use, or for any infringements upon the rights of third parties at hat may result
from its use.
All other product names or trademarks are properties of their respective owners.

ePARK
5Installation guide
Contents
Disclaimer.......................................................................................................................................................... 3
Revision log....................................................................................................................................................... 3
Contents ............................................................................................................................................................ 5
1.- So, hello! ......................................................................................................................................................................6
2.- Before the installation .............................................................................................................................................8
A.- Important Safety Instructions .............................................................................................................8
B.- Electrical wiring considerations.......................................................................................................... 9
3.- Overview.................................................................................................................................................................... 10
4.- Dimensions ............................................................................................................................................................... 12
5.- Installation ................................................................................................................................................................ 14
A.- Requirements........................................................................................................................................15
B.- Opening................................................................................................................................................. 16
C.- Positioning.............................................................................................................................................17
D.- Fixing ..................................................................................................................................................... 18
E.- Wiring..................................................................................................................................................... 19
F.- Closing.....................................................................................................................................................21
6.- Technical Data ..........................................................................................................................................................24
Need help?...................................................................................................................................................... 27
Guarantee........................................................................................................................................................ 27

ePARK
6Installation guide
1So, hello!

ePARK
7Installation guide
This manual provides commissioning information about ePark, which has been designed and tested
to allow electric vehicle charging, specified in IEC 61851
This document has different sections such as step-by-step installation procedure and technical data.
THE FOLLOWING SYMBOLS ARE USED FOR IMPORTANT
SAFETY INFORMATION IN THIS DOCUMENT
ELECTRIC RISK
Necessary precautions shall be taken to prevent any electrical risk
while the operations are carried out within the unit.
Unit must be disconnected from any power source during
commissioning.
ATTENTION!
Indicates that the damage to property can occur if appropriate
precautions are not taken
• Complies with IEC 61851; Electric vehicle conductive charging system (IEC 61851-
1:2017 and IEC 61851-21-2).
• Complies with IEC 62196, Plugs, socket-outlets, vehicle couplers and vehicle inlets
(IEC 62196-1 and IEC 62196-2).
• Standards: 2014/35/UE, LVD;2014/30/UE, EMC
• Complies with the Electrical (Safety of) Equipment Regulations 2016 and the
Electromagnetic Compatibility Regulations 2016
• RFID complies with ISO 14443A/B
• The 4G modem complies with CE/RED regulations and the Radio Equipment
Regulations of 2017.
1So, hello!

ePARK
8Installation guide
A Important Safety Instructions
Read carefully all the instructions before starting in order to
ensure properly installation of the Charge Point.
The Charge Point is designed for installation in indoor and outdoor areas. For each of the different
conditions of installation, the unit must be installed safely and ensure adequate protection.
• Charge Point must not be installed in areas where
there is potential risk of explosions.
• Do not perform any repair o manipulation of
the unit while it is energized.
• Do not install the Charge Point where falling
objects may damage the equipment.
• Only trained and qualified personnel should
have access to low-voltage electrical parts
inside the unit.
• The surface where the Charge Point is placed must
withstand the mechanical forces.
• Check the installation annually by qualified
technician.
• This unit is no shall be used for anything other
purpose than electric vehicle charging modes as
are expected in IEC 61851.
• Remove from service any item that has
a fault that could be dangerous for users
(broken plugs, caps that don’t close...).
• Do not modify this unit. If modified, CIRCUTOR will
reject all responsibility and the warranty will be
void.
• Use only CIRCUTOR supplied spare parts.
• Comply strictly with electrical safety regulations
according to your country.
• Do not use this product if the enclosure or
the EV connector is broken, cracked, open, or
shows any other indication of damage.
• Do not use any adapter, except those approved by
the EV manufacturer.
Refer to 6.- TECHNICAL DATA section for more information about environmental installation
conditions.
2Before the installation

ePARK
9Installation guide
B Electrical wiring considerations
Take into consideration this section before start wiring connec-
tions of the Charge Point.
1.- ELECTRICAL PROTECTIONS
It is possible that the Charge Point does not include electrical protection elements.
If this device has internal electrical protections, they are installed in each socket to protect the user
against electrical failure, in accordance with the international standard IEC 61851-1:2017.
In order to guarantee the total protection of the users and the installation (power supply line
included) in front of any electrical hazard, it is mandatory to install a main circuit breaker (MCB) and
a residual current device (RCD) upstream of the charger.
These electrical protections and the rest of the installation have to be aligned with the local and
national rules. The selectivity of the protections has to be guaranteed at all times.
3.- POWER SUPPLY LINE DIMENSIONING
The dimensioning of the input power supply line of the Charge Point must be checked by a qualified
electrician. Note that various factors such as cable length between distribution board and Charge
Point, maximum output current of the Charge Point may have influence of the selected cable.
In such cases, increasing the cable cross-section it is required to adapt the temperature resistance
of the power supply line.
3.- MAXIMUM OUTPUT CURRENT
Please refer to the TECHNICAL DATA section to consult the default factory settings from maximum
output current of the Charge Point.
If the power supply is less than maximum output current and adjustment to a lower nominal current
needs to be performed.
2Before the installation

ePARK
10 Installation guide
What’s included:
Installation
Guide
Charge Point Installation
Guide
Allen wrench
2.5 mm
3Overview

ePARK
11Installation guide
1
2
3
52
4
4
4
5
7
6
5
Description
1LED beacon 5Closing box holes
2Cable glands 6LCD
3Plugs(1) 7RFID reader
4Wall support holes
(1) Connectors may vary by model.
3Overview

ePARK
12 Installation guide
335 315
1 79,70
335
39
Measures in mm
4Dimensions

ePARK
13Installation guide
168
105
62.5
52.5
20 (2)
3 9. 5
255
20.5
62.5 52.5
34 34
230
(2) This measurement may vary.
Measures in mm
4Dimensions

ePARK
14 Installation guide
Material:
• Allen wrench of 2,5 mm is included in the installation kit.
• Screws, sealing washers and plastic anchors are not included.
• The fastening system of the Charge Point has been designed to be installed on
a wall.
This system has been tested on a concrete wall, to be securely
fixed in such conditions is recommended to use:
3 x Inox A2 wall screws: DIN 7982 Ø4,8x3
3 x plastic anchors: 6x40 or 8x40
If the wall surface has different properties, the screws and plastic
anchors must be defined by a qualified installer.
Tools:
Screw driver Ratchet(3)
2.5mm Allen
Driller
Tap drill 6/8M
(3)Ratchet tool can be used to open/close the Charge Point if required by the conditions of installation.
5Installation

ePARK
15Installation guide
A Requirements
• Please comply with your country regulations.
• The Charge Point shall be installed on a wall or on CIRCUTOR accessories.
• When installing the unit, some space shall be reserved for usability, maintenance and safety
reasons. The picture below shows the recommended minimum distances:
300
1100
300
300
Dimensions in mm
If the recommendations are not followed as described, CIRCUTOR will
reject all responsibility and the warranty will be void.
5Installation

ePARK
16 Installation guide
B Opening
Open the ePARK using allen wrench.
Allen wrench 2,5 mm
Screw
DIN-7380-2 M4x14 INOX
Sealing washer
DIN 7712 4.8 14MM INOX
Use the ratchet tool to open/close the change point wall
fixed.

ePARK
17Installation guide
Remove PCB plastic support to connect the ethernet and put the screw into the wall.
RJ45 Wall Screw
PCB plastic support
methacrylate
screws
C Positioning
Drill the wall.
Measures in mm.
1100
255
230
115
Drill bit M 6/8

ePARK
18 Installation guide
D Fixing
Place de unit on the previously leaky points and fix it by the screws.

ePARK
19Installation guide
E Wiring
Use provided cable glands in order to maintain the IP protection.
A A
B
Cable glands
M32
• The current of the power supply can be limited. In order to perform this adjustment please refer
to the Instruction Manual.
• The IEC-61851-1 ed 3 standard indicates that each plug shall have protections. In case the
Charge Point has no protections inside, they shall be upstreams. It is recommended that these
protections be as follows:
• RCD: Residual current device. Standards: IEC 61008-1, IEC 61009-1,IEC 60947-2 or IEC 62423.
• RCD(s) rated residual operating current not exceeding 30 mA.
• For AC fault current, RCD(s) protecting that connecting points shall be at least type A.
• RCD(s) shall disconnect all live conductors.
• DC fault current shall be measured by a RCD type B or a appropriate equipment that ensures
the disconnection of the supply in case of DC fault current above 6 mA.
• MCB: Miniature circuit breaker. Standards: IEC 60898-1, IEC 60947-2 or IEC 61009-1.
• MCB(s) minimun breaking capacity 4 kA.

ePARK
20 Installation guide
SINGLE-PHASE CHARGE POINT
• Connect to the 230V~.
THREE-PHASE CHARGE POINT
• Connect to the 400V~.
• If the Power Supply is Single-Phase,
connect L1 and N.
L1
L2
L3
N
PE
L
LA L B
NA NB
N
Protections
A
Protections Protections
B
1 CONNECTORS 2 CONNECTORS
PE
Do not forget to connect the ground cable to the ground terminal.
Make sure all screws are securely tightened.
Terminal block maximum cross-section: 16mm2
S
Type of cable allowed by the terminal block: Copper.
Cu
Note: The proper earthing system must be TT or TN-S. The ground loop impedance measurement
for the entire installation must be less than 80 ohms; however, it could be even less if required
by national regulations. At least once a year it is recommended to carry out the verification of the
installation grounding by qualified personnel when the terrain is drier.