FOS Technologies FOS BEAM IP User manual

1
FOS Beam IP
USER MANUAL
Thanks for choosing our goods please read this manual carefully before
your operating and keep this manual for future needs

2
CATALOG
1、Attachment and body size________________________________________________ 3
2、Installation and connecting_______________________________________________ 4
3、Safety Instructions_______________________________________________________ 6
4、Specifications____________________________________________________________ 7
5、DMX channel_____________________________________________________________ 8
6、Cleaning and maintenances_____________________________________________ 11
7、Troubleshooting_________________________________________________________ 12
8、MAINTENANCE__________________________________________________________ 12

3
1、Attachment and body size
Body size

4
2、Installation and connecting
The projector can be installed on the floor resting on special rubber feet ,on the truss or the wall.
WARNING :With the exception of then the projector is positioned on the floor,the safety cable
must be fitted.
This must be securely fixed to the support of the projector and then connected to the fixing point at
the center of the base.
Please ensure that the device is always connected to the earth properly
The manufacturer will not accept liability for any resulting damages caused by the non-observance
of this manual or any unauthorized modification to the device.
Avoid looking directly into the light source meant especially for epileptics!
Rigging
Concerning rigging, trussing for this device, please follow the European and national guidelines.
Only the qualified technicians are allowed for the device installation, The device must never be
mounted for a possible swinging position, and a safety cord attached must always be used.
Fixture Installation
When suspending the fixture above ground level, verity that the structure can hold at least 10 times
the weight of all installed devices.
Verify that all external covers and rigging hardware are securely fastened and use an approved
means of secondary attachment such as a safety cable.

5
In DM X Controller mode, at the last fixture in the chain, the DMX output has to
be connected with a DM X terminator. This prevents electrical noise from
disturbing and corrupting the DMX control signals.
Th e DMX terminator is simply an XLR connector with a 90 - 12 0Ω (ohm) 1/4
watt res is to r connected across pins 2 and 3 o f a male XLR connector (DATA+
and DATA-). This terminator is then p lugged into the output socket o n the last
fixture in the daisy chain to terminate the line. Using a cable terminator will
decrease the possibilities of erratic behavior.

6
3、Safety Instructions
★This product guide contains important information about the safe installation
and use of this projector. Please read and follow these instructions carefully and
keep this manual in a safe place for future reference.
★When unpacking and before disposing of the carton, check there is no
transportation damage before using the projector. Should there be any damage
caused by transportation,consult your dealer and do not use the apparatus
★The projector is not designed or intended to be mounted directly on to
inflammable surfaces.
★The projector is only intended for installation, operation and maintenance by
qualified personnel.
★The projector must be installed in a location with adequate ventilation, at
least 1m from adjacent wall surfaces. Be sure that no ventilation slots are
blocked
★Do not project the beam onto inflammable surfaces, minimum distance is 5m.
★Do not attempt to dismantle and/or modify the projector in any way. Electrical
connection must only be carried out by qualified personnel.
★Before installation, ensure that the voltage and frequency of power supply
match the power requirements of the projector.
★It is essential that each projector is correctly earthed and that electrical
installation conforms to all relevant standards.
★Do not connect this device to any other types of dimmer apparatus.
★Make sure that the power-cord is never crimped or damaged by sharp edges.
Never let the power-cord come into contact with other cables. Only handle the
power-cord by the plug. Never pull out the plug by tugging the power-cord.
★The projector should always be installed with a secondary safety fixing. A
safety cord is supplied for this; it should be attached as shown in “installing the
projector” section.
★There is no user serviceable parts inside the projector; do not open the
housing and never operate the projector with the covers removed.
★This device is not designed for permanent operation. Consistent operation
breaks will ensure that the device will serve you for a long time without defects.
★The maximum ambient temperature t = 45°C must never exceeded.
★If this device is operated in any other way other than the one said in this
manual, this device may suffer damages and thus the warranty becomes void.
★Always disconnect from the mains, when the device is not in use or before
cleaning it or before attempting any maintenance work

7
4、Specifications
Voltage:AC90-245V 50-60Hz
Lamp：YODN SIRIUS HRI 350W/440W
Ballast：YODN MSD R17/S20
Power:500W/600W
Average lifespan:1500-2000 hours
Focus ：linear electronic focus
Lamp temperature：7500K
IP Rate：IP55
Dimmer ：Super smooth dimmer
Color temperature：2500K、3200K （special order）
Strobe ：Independent strobe, 0.5 to 20 times/ seconds
Color wheel：11 color filter wheel（can order with CMY)
Beam angle:2°
Lens :183mm Beam :170mm
Fixed gobo wheel:12+1+animation range
Prism：16 facet +16 facet （standard，accept special order)
Control system：DMX ，Master/Slave mode,AUTO Mode
Pan/Tilt : 540 degree , Tilt : 275 degree
Channel ：Simple channel : 16 CH

8
5、DMX channel
Channel
Value
Function
1
PAN
0-255
0-100%
2
PAN-FINE
0-255
±1%
3
TILT
0-255
0-100%
4
TILT-FINE
0-255
±1%
5
Pan/Tilt SPEED
0-255
Fast -> Slow
6
DIMMER
0-255
0-100%
7
STROBE
0-3
Close
4-103
Strobe，Slow -> Fast
104-107
Open
108-207
Pulse: Slow -> Fast
208-212
Open
213-225
Random: Slow
226-238
Random: Middle
239-251
Random: Fast
252-255
Open
8
COLOR
0-4
Blank
5-9
Color 1
10-14
Color 2

9
15-19
Color 3
20-24
Color 4
25-29
Color 5
30-34
Color 6
35-39
Color 7
40-44
Color 8
45-49
Color 9
50-54
Color 10
55-59
Color 11
60-64
Blank + Color 1
65-69
Color 1 + Color 2
70-74
Color 2 + Color 3
75-79
Color 3 + Color 4
80-84
Color 4 + Color 5
85-89
Color 5 + Color 6
90-94
Color 6 + Color 7
95-99
Color 7 + Color 8
100-104
Color 8 + Color 9
105-109
Color 9 + Color 10
110-114
Color 10 + Color 11
115-119
Color 11 + Blank
120-185
Rotation(CW): Fast -> Slow
186-189
Stop
190-255
Rotation(CCW): Slow -> Fast
9
GOBO
0-3
Blank
4-7
Gobo 1
8-11
Gobo 2
12-15
Gobo 3
16-19
Gobo 4
20-23
Gobo 5
24-27
Gobo 6
28-31
Gobo 7
32-35
Gobo 8
36-39
Gobo 9
40-43
Gobo 10
44-47
Gobo 11
48-51
Gobo 12
52-55
Gobo 13

10
56-59
Gobo 14
60-64
Gobo 1 Shake: Slow -> Fast
65-69
Gobo 2 Shake: Slow -> Fast
70-74
Gobo 3 Shake: Slow -> Fast
75-79
Gobo 4 Shake: Slow -> Fast
80-84
Gobo 5 Shake: Slow -> Fast
85-89
Gobo 6 Shake: Slow -> Fast
90-94
Gobo 7 Shake: Slow -> Fast
95-99
Gobo 8 Shake: Slow -> Fast
100-104
Gobo 9 Shake: Slow -> Fast
105-109
Gobo 10 Shake: Slow -> Fast
110-114
Gobo 11 Shake: Slow -> Fast
115-119
Gobo 12 Shake: Slow -> Fast
120-124
Gobo 13 Shake: Slow -> Fast
125-129
Gobo 14 Shake: Slow -> Fast
130-190
Rotation(CW): Fast -> Slow
191-194
Stop
195-255
Rotation(CCW): Slow -> Fast
10
PRISM 1
0-127
Out
128-255
Prism 1 in to the light beam
11
PRISM 2
0-127
Out
128-255
Prism 2 in to the light beam
12
PRISM-ROT
0-127
0-100%
128-191
Rotation(CW): Fast -> Slow
192-255
Rotation(CCW): Slow -> Fast
13
FROST
0-255
0-100%

11
14
FOCUS
0-255
0-100%
15
LAMP-CONTROL
0-50
Unused
51-100
Lamp ON
101-150
Lamp OFF
151-200
Half-power
201-255
Full-power
16
REST
6、Cleaning and maintenances
☆In order to en sure the projector could work normally.Is should be kept clean
always.It is recommended that the fans and ventilation in let should be cleaned
every 60days.The lens should also be regularly cleaned to maintain an optimum
light output. Do not use any type of solvent on lens .It will damage the projector.
Suggestion：The continue usage of the light don’t exceed 4 hours .Or it will
shorter the usage if the lamp.Please use the alternative operation to solve this
problems.
☆Please disconnect the power supply when begin to maintenaceor take down
the light.Please let the parts of cooling for at lease 10 minute before install.If
need to replace the lamp ,please wait 15 minutes to let the lamp cool down
completely or which maybe burned down.
☆Please inspect the lens or other moving parts timing and keep them clear and
0-100
Unused
101-150
Pan/Tilt Reset
151-200
Head Reset
201-255
All Reset

12
static .If find any damaged of losseness,must change the lamp or fix the lamp in
order to avoid the accident.
☆The light use the strong cooling system.Is is easy for the dirty to be
collected .Please do clear the hot-sak one time two weeks at least.
☆After you use the light,please check he intake place whether there are some
wastepaper,please clean it up,or the windmill will break down and causing fire.
7、Troubleshooting
8、MAINTENANCE
To maintain optimum performance and minimize wear fixtures should be
cleaned frequently. Usage and environment are contributing factors in
determining frequency.
As s general rule, fixtures should be cleared at least twice a month. Dust build
up reduces light output performance and can cause overheating. This can lead
to reduced lamp life and increased