PR Lighting LED Studio 3800T User manual

LED Studio 3800T
LED Studio 3800D
PR-3800T
PR-3800D
This product manual contains important information about the safe installation and use of this projector.
Pleasereadandfollowtheseinstructions carefullyandkeepthismanualinasafeplace forfuturereference.
PRLIGHTINGLTD.
http://www.pr-lighting.com

2/14
INDEX
SAFEUSAGE OFTHEPROJECTOR………………………………………………………………………………
3
INSTALLINGTHEPROJECTOR…………………………………………………………………………………..
4
CONTROLCONNECTION…………………………………………………………………………………………
5
DMXTERMINATOR………………………………………………………………………………………………..
6
SETUPOPTIONS-PROJECTORCONFIGURATION………………………………………………………………
6
TO SETTHE DMXSTARTADDRESS……………………………………………………………………………..
7
OPERATIONMENU………………………………………………………………………………………………..
7
DMXPROTOCOL………………………………………………………………………………………………….
8
INDICATIONOFLED DIGITALTUBE…………………………………………………………………………….
8
MAINTENANCE……………………………………………………………………………………………………
9
TROUBLESHOOTING………………………………………………………………………………………………
9
TECHNICALDATA…………………………………………………………………………………………………
10
ELECTRICALDIAGRAM…………………………………………………………………………………………..
12
COMPONENTORDERCODES……………………………………………………………………………………
13
BACKCOVER…………………………………………………………………………………………………
14
Please note that as part of our ongoing commitment to continuous product development, specifications are subject to
change without notice. Whilst every care is taken in the preparation of this manual we reserve the right to change
specifications in the course of product improvement. The publishers cannot be held responsible for the accuracy of the
information herein, or any consequence arising from them.
Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the
unit are in good condition before installation and use. Should there be any damage caused by transportation, consult
your dealer and do not use the unit. Any damage caused by improper use will not be assumed by the manufacturer and
/ or dealer.
ACCESSORIES
These items are packed togetherwith theprojector:
Name
Quantity
Unit
Remark
Clamp
1
Pc
Safetycord
1
Pc
DMX signalcable
1
Pc
With socket and plug
Powercord
1
Pc
Thismanual
1
Pc

3/14
SAFE USAGE OF THE PROJECTOR
When unpacking and before disposingof the carton, check there is no transportation damage before using the projector. Should there
be anydamage causedbytransportation, consult yourdealer and do not use the apparatus.
The projector can be used only indoors, IP20. Keep the projector clean; avoid its use in humid, hotand dustyplaces; keep water and
otherliquids fromtouchingtheprojector.
The projector is not designed or intended to be mounted directly onto inflammable surfaces.
Theprojectorisonly intended forinstallation,operationand maintenance byqualified personnel.
Donotprojectthebeamontoinflammablesurfaces,minimumdistanceis2m. 2m
Avoid directexposuretothe lightfrom thelamp.Thelightis harmfultoeyes.
Donotattempttodismantleand/or modify theprojector inanyway.
Electrical connectionmustonlybe carried outbyqualifiedpersonnel.
Before installation,ensure that the voltage and frequencyofpower supplymatch the power requirements of the projector.
Itisessentialthateachprojector iscorrectly earthedandthatelectrical installation conforms to allrelevantstandards.
Do notconnectthisdevicetoanyothertypesofdimmerapparatus.
When the projector is hanged to a high place, please usea safetycord provided to pass through the projector handles as a secondary
safety fixing for safety seasons. For details, refer to “INSTALL THE PROJECTOR ” section.
Exterior surface temperatures of the projector after 5 minutes’ operation is 45℃,whenachievingsteadystateitis55℃.
There is no user serviceable parts inside the projector, do not open the housing and never operate the projector with the covers
removed.
If you have any questions, don’t hesitate to consult your dealer or manufacturer.
Alwaysdisconnectaprojectorfrompowerbefore installationorcleaning oranymaintenancework!

4/14
INSTALLTHE PROJECTOR
The projector is hung when used, but not hung by any of its side. It can be manually rotated within a range of 90 degrees. Before
installation,Take1clampsand1safetycordoutfromthepackage and mount1 clamp onthemountinghandleoffixture with1retainer.
Hang the fixture on the structure and fasten the screws attached to the clamp. Always ensure that the projector is firmly
anchored to avoid vibration and slipping whilst functioning. Always ensure that the structure to which you are
attaching the projector is secure and strong enough to support the weight of the fixture. For safety the projector should
have a secondary fixing with a safety cord through the handle of the unit to ensure safe mounting.
Warning:
1. Theprojectormustbeliftedorcarriedbythehandlesinsteadofclamps.
2.Forsafetythesafety cordshouldafford 10timesof the unit’s weight.

5/14
CONTROLCONNECTION
Connection betweenthe controller and a projector and betweenone projector and another must be made witha 2 core-screened cable,
with eachcore having at least a 0.5mm diameter. Please use the projector’s cannon 5-pin signalinputandoutputcablesas connection.
The5-pinsignalconnectionsareconnectedasshowninthefigureabove.
Note:Care shouldbe taken toensurethatnone ofthepinstouchthemetallicbodyoftheplugoreachother.Thebodyoftheplugisnot
connected inanyway.Theprojectoracceptsdigitalcontrol signalsinprotocolDMX512(1990).
Maximum 32 units can be connected in series by 5-pin signal cable. Connect the controller’s output to the first fixture’s input, and
connect the first fixture’s output to the second fixture’s input and connect the rest fixtures in the same way. Eventually connect the last
fixture’s output to a DMX terminator as shown in the figure below.
Note: Forsynchronous control, StartAddresses for all slave units must be same.
Each unit should be connected to power supply individually and the voltage and frequency of the power supply should match those
indicated on nameplate.

6/14
DMXTERMINATOR
In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents
electrical noise fromdisturbingandcorruptingtheDMXcontrol signals.
The DMX terminator is simply an XLR connector with a 120(ohm) resistor connected acrosspins 2 and 3, which is then plugged
intotheoutput socketonthelastprojector in the chain.The connections are illustrated below.
SETUPOPTIONS-PROJECTOR CONFIGURATION
To browse through or change a fixture’s configuration, after ENTER button has been pressed for about 3 seconds, the display of
AddR means the entrance of the menu. To set or browse through a fixture’s settings, press buttons of UP and DOWN. After button
ENTER is pressed, a sub-menu is entered showing current parameters while indication flashing. Press button UP or DOWN to
change values(plusorminus)
PressbuttonENTERtosave your settingsorenterintotheupperlevel menuandtheindication stops fromflashing.
Press FUNCto enterintothe upper level menu(parametersnotsaved )orbrowse throughtheupper level menu.
After FUNC is pressed for more than 1second or buttons not pressed for more than 1 minute, it will go back to the main menu
displayingthecurrentbrightnessvalue.
While DMX signals are available, Signal LED indication will be on and current DMX address displayed, otherwise the current
brightnessvaluedisplayed.

7/14
TO SETTHE DMX STARTADDRESS
Eachprojector must be givena DMX start address so that the correctprojector responds to the correct controlsignals. This DMX start
address is the channel number from which the projector starts to “listen” to the digital control information being sent out from the
controller.Theprojector has2DMXchannel, so settheNo. 1 projector’s address 001, No. 2 projector’s address 003, No. 3 projector’s
address005,andsoon.
Turnonthefixture,ifthecontrolpanelis locked,pressENTER formore than3suntil isdisplayedto unlockit.
PressbuttonFUNCorUPorDOWN to find “AddR” menu. will bedisplayed.
AfterENTERispressed, DMXaddress willbedisplayed.
PressUPorDOWNtosetDMXaddress.
At this time, DMX address displayed will flash continuously. Press button ENTER to confirm, then address has been automatically
saved.Whenthe projectorispowerednext time, the last saved settings will automatically used.
PressbuttonFUNC,it willreturnto the uppermenu.

8/14
DMX PROTOCOL
DMXChannelMode
CHANNEL
FUNCTION
DMX
DESCRIPTION
1
Dimmer
000-255
2
Strobe
000 -007
NO
008 -255
Strobefrom slow to fast
INDICATION OF LED DIGITALTUBE
DMXIndication
ON
DMXSignal
OFF
NODMXSignal

9/14
MAINTENANCE
To prolong the life of the projector, it is very important to do the maintenance work. If the projector is idle for a long time, damp,
smoke or particularly dirty surroundings can cause greater accumulation of dirt on its cover and housing. So it should be cleaned to
maintain an optimumlight outputandatthesametimetopreventitfrombeing corruptedbyacidgas.
Cleaning frequencydependsontheenvironmentin whichthe fixture operates.Softcloth andtypical glass cleaningproducts shouldbe
used forcleaning. Itisrecommendedtocleanprojectoratleastonceevery20days.
Donot useanyorganicsolvent,e.g.alcohol,tocleanhousingoftheapparatus.
TROUBLESHOOTING
PROBLEM
ACTION
The projector doesn’t switch on
Powerconnectionisnotcorrect.
Power supply is damaged or abnormal. Call a qualified personnel to fix
it.
Connection of control board is not correct. Call a qualified personnel to
fixit.
Theprojectorcanbeturnedon,but LEDsdo not
emit light andareoutofcontrol.
Connection of LED board is not correct. Call a qualified personnel to fix
it.
Thelampcomes on but the projector doesn’t
respondtothecontroller
Makesurethattheprojectoriscorrectlyconfigurated.
Replaceorrepair theDMX cable.
Thebeamappearsdim
Theprojectoristoohot.Take ventilation measures to makeitcool.

10/14
TECHNICALDATA
VOLTAGES:
AC 100V-240V 50/60Hz
POWERCONSUMPTION:
70W@220V
LED:
Powerconsumption
60W
Quantity
1pcs
ManufacturersRated LED Life
50000Hours
COLOURTEMPERATURE:
PR-3800T：3200K
PR-3800D：5600K
DIMMER:
0-100% linearly adjustable
COLOURRENDERINGINDEX
Ra≥86
LUMINOUS FLUX
PR-3800T：690lm
PR-3800D：850lm
BEAMANGLE:
Fieldangle(one-tenth-peak) θ :29°-59°
CONTROL:
DMX512,5pininterfaces
HOUSING:
High-intensitydie-castingaluminum,IP20
WORKENVIRONMENTTEMPERATURE:
-20°C~40°C
WEIGHT:
3. 5kg