FOS Technologies SuperStorm L006796 User manual

FOS SuperStorm
User manual

2/12
Safety warning information
After receiving the lights, please open to check whether there is any damages caused by transportation. In
case of damages caused of transportation, please don’t this device and contact your dealer or manufacturer as
soon as possible.
The projector is for indoor and outdoor use, IP65.
Do not install the fixtures onto inflammable surfaces directly.
The fixture is only intended for installation, operation and maintenance by qualified personnel.
Do not project the beam onto inflammable surfaces, minimum distance is 3 meter. 3m
Avoid direct exposure to the light from the lamp. The light is harmful to the eyes.
Do not attempt to dismantle and/or modify the projector in any way.
Electrical connection must only be carried out by qualified personnel.
Before installation, ensure that the voltage and frequency of power supply match the power requirements of
the fixture.
It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant
standards.
Do not connect this device to any other types of dimmer apparatus.
The projector should always be installed with a secondary safety fixing. A safety cord is supplied for this; it
should be attached as shown in “installing the projector” section.
Shields and lens shall be changed if they have become visibly damaged to such an extent than their
effectiveness is impaired, for example by cracks or deep scratches.
Exterior surface temperatures of the luminaire after 5 minutes operation is 45℃, when steady state is
achieved 70℃. There is no user serviceable parts inside the projector, do not open the housing and never
operate the fixture with the covers removed.
There is no user serviceable parts inside this light, please check whether all covers or shells have been
installated and screws have beed tightened securely. It is forbidden to use lights with covers(or shell) open.
If you have any questions, don’t hesitate to consult your dealer or manufacturer.

3/12
Always disconnection from Power before the device’s installation, cleaning and maintenance
Installation
1.Installed on the ground
2.Hanging 3.Splicing
4.Diffuser

4/12
Take out 2 clamps and 1 safety rope, install the 2 clamps on the bottom of the fixture with the 4 quick knob
attached to the clamps , then hang the fixture on the fixed support with the clamp, and tighten the clamp lock bolt
to fix the fixture. Please confirm that the fixture installation is stable and reliable, and ensure that the hoisting
position has sufficient strength to withstand the weight of the fixture. please carry the randomly equipped safety
rope through the bottom of the fixture holder for auxiliary hoisting to ensure safety.
Warn：
1、The clamps are only used when install the fixtures. It is strictly forbidden to use the clamps as a handle to carry
the fixtures.
2、For safety reasons, please use a safety rope that can withstand 10 times the weight of the fixture through the
safety hole of the fixture body.
3、Side hang the fixtures are forbidden .
Signal and power connect
DMX 512
2DATA-
DATA+
3
1GND
FUNCTION
PIN
三芯
DMX OUT DMX IN
21
3
2
1
3
For the connection of control signals, 2-pin shielded cables with a diameter not less than 0.5 mm must be
used between the fixture and the controller and between the fixtures. Please use the 3-pin signal output /
incoming line of the lamp to connect. The connections between the 3-pin signal line ports are shown in the figure
above. It must be noted that the 3 pin of the XLR plug / socket must not be in contact with the inner shell or
between the cores when connecting. The XLR plug / socket and the XLR control cable cannot be connected in
any other way than the connection shown in the figure above. This product receives the international standard
DMX512 (1990) control signal.
The signal connection of multiple fixtures, the maximum number of connection is 32 fixtures, use a 3-pin
signal cable from the DMX output port of the controller to the DMX input line of the 1st fixture, and connect from
the DMX output line of the first fixture To the DMX input line of the second fixture, and so on, until all the fixtures
are connected.
When the first fixture is not connected to the controller (the signal line connection between the other fixtures
remain unchanged), it is the connection mode of master-slave synchronous control. However, to achieve
master-slave synchronization control, the first fixture should be set as the master in the menu, and the remaining
fixtures should be set as slaves (the default value is slave).
When connecting the power supply, the power supply of each fixture should be connected separately. Please note
that the power supply voltage and frequency must match with the power supply voltage and frequency listed in the
product manual.

5/12
Function and installation
power-on password:UP - DOWN- UP - DOWN- ENTER
Press button UP or DOWN if you want to browse through the various Setup Options.
Press button ENTER to save your settings or enter the next menu.
Press button UP or DOWN to shift.
Press button Menu will return to the upper menu one by one.
DMX address setting
When using the controller to control multiple fixtures，each fixture shall be provided with a DMX address to
receive signals from the controller and respond correctly, There are 3 control modes in this product, which are
simple mode, standard mode and extent mode.
For example: The fixture has 20 channels at standard mode.
We set the 1st fixture :DMX Address 001, then the 2nd fixture DMX Address 021，the 3rd fixture DMX
Address 041，the 4th fixture 61，… …and so on.
Turn on the fixture，If operating menu is locked，press ENTER for 5 Sec, the fixture will be unlocked；
Then press Menu 、or UP or DOWN to find AddR menu；
Press ENTER ，display DMX Address；
Press UP / DOWN set DMX Address value；
Press ENTER to confirm，then the fixture automatically saved this DMX address
Press Menu will return to the upper menu

6/12
Operation menu
power-on password:UP - DOWN- UP - DOWN- ENTER
1st LEVEL
2nd LEVEL
1rd LEVEL
1th LEVEL
DMX Address
XXX
（1~499）
enter
DMX channel
model
13 CH (DMX)
enter
64 CH (DMX)
enter
89CH (DMX)
enter
OFFline statu
Hold
enter
Manual
enter
Auto
enter
OFF
enter
On
enter
Manual Color
Dimmer
0-255
Strobe
0-255
Macro 1
0-255
Macro S1
0-255
Macro 2
0-255
Macro S2
0-255
Macro Color
0-255
Char1
0-255
Char 2
0-255
Char 3
0-255
Char 4
0-255
Char 5
0-255
Char Color
0-255
BackColor Red
0-255
BackColor Green
0-255
BackColor Blue
0-255
White 1
0-255
White 2
0-255

7/12
White 3
0-255
White 4
0-255
White 5
0-255
White 6
0-255
White 7
0-255
White 8
0-255
Auto Prgram
Show RGB
0-255
Speed RGB
0-255
Show W
0-255
Speed W
0-255
Char Color
0-255
Char1
0-255
Char 2
0-255
Char 3
0-255
Char 4
0-255
Char 5
0-255
Display
Ch / En
中文
English
Display Direct
Normal
reverse
Backlight
ON
30s
Parameter
NO
yes
Default
No
Yes
Info
RDM UID
Channel
Ver
Time
Temperature

8/12
DMX channel list
13 Channel
Channel
Name
DMX
Value
DMX
Percentage
Description
1
Dimmer
0-255
0-100%
0-100%Intensity
2
Strobe
0-255
0-100%
0-100% Strobr frequency
3
Macro 1
0-10
0-100%
invalid
11-20
0-100%
Fx 1
.....
245-255
Fx 25
4
Macro 1S
0-255
5
Macro 2
0-10
0-100%
invalid
11-20
0-100%
Fx 1
.....
245-255
Fx 25
6
Macro 2S
0-255
0-100%
7
Macro 2CF
0-255
0-100%
8
Macro 2CB
0-255
0-100%
9
W-S
0-255
0-100%
10
Red-C
0-255
0-100%
0-100% red
11
Green-C
0-255
0-100%
0-100% Green
12
Blue-c
0-255
0-100%
0-100% Blue
13
W-C
0-255
0-100%
0-100% White
64 Channel
Channel
Name
DMX
Value
DMX
Percentage
Description
1
pixel module 1 R
0-255
0-100%
0-100% red
2
pixel module 1 G
0-255
0-100%
0-100% Green
3
pixel module 1 B
0-255
0-100%
0-100% Blue
3
pixel module 1 W
0-255
0-100%
0-100% W
....
......
0-255
0-100%
.......
61
pixel module 16 R
0-255
0-100%
0-100% red
62
pixel module 16 G
0-255
0-100%
0-100% Green

9/12
63
pixel module 16 B
0-255
0-100%
0-100% Blue
64
pixel module 16 W
0-255
0-100%
0-100% W
89 Channel
Channel
Name
DMX
Value
DMX
Percentage
Description
1
Dimmer-W
0-255
0-100%
0-100%Intensity
2
Dimmer-RGBW
0-255
0-100%
0-100% Strobr frequency
3
Strobe
0-255
4
Macro 1
0-10
0-100%
invalid
11-20
0-100%
Fx 1
.....
245-255
Fx 25
5
Macro 1S
0-255
6
Macro 2
0-10
0-100%
invalid
11-20
0-100%
Fx 1
.....
245-255
Fx 25
7
Macro 2S
0-255
0-100%
8
Macro 2CF
0-255
0-100%
9
Macro 2CB
0-255
0-100%
0-100% W
10
White 1
...
.....
0-255
0-100%
25
White 16
0-255
0-100%
0-100% W
26
pixel module 1 R
0-255
0-100%
0-100% red
28
pixel module 1 G
0-255
0-100%
0-100% Green
29
pixel module 1 B
0-255
0-100%
0-100% Blue
30
pixel module 1 W
0-255
0-100%
0-100% W
....
......
0-255
0-100%
.......
86
pixel module 16 R
0-255
0-100%
0-100% red
87
pixel module 16 G
0-255
0-100%
0-100% Green
88
pixel module 16 B
0-255
0-100%
0-100% Blue
89
pixel module 16 W
0-255
0-100%
0-100% W
Channel priority: dimming> built-in program call > user program call>ARGBW dimming >HSV
dimming> Macro Instruction> Color Temperature

10/12
Maintenance
To ensure the reliability of the projector it should be kept clean. It is recommended that the fans should be cleaned
every 15 days. The lens and dichroic color filters should also be regularly cleaned to maintain an optimum light output.
Do NOT use any type of solvent on dichroic color filters.
Cleaning frequency depends on the environment in which the fixture operates: damp, smoke or particularly dirty
surroundings can cause greater accumulation of dirt on the unit’s optics. A soft cloth and typical glass cleaning products
should be used in cleaning. It is recommended to clean the external optics at least once every 20 days and clean the
internal optics at least once every 30 / 60 days.
Do not use any organic solvent, e.g. alcohol, to clean the reflector mirror, dichroic color filters or housing of the
apparatus.
Trouble shooting
Problems
Action
The fixture wont switch on properly
power cord connection is not normal
the switching power supply is damaged or the connection is not
normal, professional qualified technician needed to carry out
maintenance and repair
control board connection is not normal，professional qualified
technician needed to carry out maintenance and repair
The fixture switch on ，but LED not
bright and not controlled
LED board connection is not normal ，professional qualified
technician needed to carry out maintenance and repair
Switch on and light normally，but not
controlled by controller
check the DMX starting address code setting is correct or not
Check the XLR signal line is damaged or not
The fixture is dim and the brightness
drops sharply
The fixtures temperature is too high, please take necessary
ventilation and heat dissipation measures

11/12
Technical data
Input voltage：
AC 100V/120V/200V/220V /230V/240V 50/60Hz
Power ：
700W@220V
LED light source：
Strobe Tube LEDS
LED Type: 3535 5W 6500K LEDs
LED Count: 144
LED Colors: Cool-White
LED Segments: 16
Strobe Panel LEDs
LED Type: 5050SMD 2W RGBW 4 in1
LED Count: 242
LED Colors: Cool-White
LED Segments: 32 (2x16)
Working lifetime
50000h
Dimmer ：
0-100% linear dimming
Strobe ：
Electric strobe，0.3-20pcs/sec Max 20 Hz
Control mode：
International standard DMX 512signal，3 Pin (5 Pin) DMX512 interface RDM
Wireless ：2.4 GHz W-DMX™ (optional)
3 channel modes
Master-slave
Stand-alone mode
Self-test mode
Other functions：
Adjustable horizontal and vertical speed
Display fixture using time
Display software version number
Modular structure for easy maintenance
Speed-regulating radiator
Connector
Power : Seetronic Powercon Ture1
DMX: Seetronic XLR Cable Connector

12/12
Shell and protection level：
High-strength casting aluminum alloy，IP66 black shell（white optional）
Working temperature：
-20°C～40°C
Weight：
8.9 Kg
Produce size：
See below