Franke FAID0004 User manual

ZMI_001_2030019057-FAID0004_#SALL_#AQU_#V3.fm / 01.05.22
Installation and operating instructions Montaż i instrukcja obsługi
EA-Nr.: 7612982217050
Best.-Nr.: 2030019057
FAID0004
DE
EN
PL

2
Inhaltsverzeichnis11.fm
...................................................................................... 3
Please refer to the graphics in the German Installation and
Operating Instructions.
...................................................................................... 10
Prosimy przyjąć grafikę z niemieckiej instrukcji montażu i
obsługi.
EN
PL

- 3 -
ZMI_001_2030019057-FAID0004_#SEN_#AQU_#V2.fm
0English
Emergency shower with pull rod
Please refer to the graphics in the German installation and operating instructions.
Table of contents
1. Abbreviations and units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4. Important notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Description of product
5. Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
6. Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
7. Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
8. Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
9. Installation example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Assembly, function and commissioning
10. Assembly for actuation from right . . . . . . . . . . . . . . . . . . . . . . . . . 5
11. Assembly for actuation from left . . . . . . . . . . . . . . . . . . . . . . . . . . 7
12. Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Maintenance
13. Maintenance and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
14. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
15. Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1. Abbreviations and units
EA-Nr. European article number
Best.-Nr. Aquarotter order number
Conversion 1 mm = 0.03937 inches
1 inch = 25.4 mm
All length specifications in the graphics are in mm.
EN

ZMI_001_2030019057-FAID0004_#SEN_#AQU_#V2.fm
- 4 -
2. Key
Warning!
Failure to observe can result in bodily injury or even death.
Caution!
Failure to observe can result in material damage.
☞Important!
Failure to observe can cause the product to malfunction.
☞Useful information for optimum handling of the product.
3. Warranty
Liability is accepted in accordance with the General Terms and Conditions of
Business and Supply.
Use only genuine spare parts!
4. Important notes
• Installation, commissioning and maintenance must be performed only by a
qualified expert in accordance with the instructions provided, legal requirements
and recognised engineering standards.
• All technical connection regulations specified by the local water and electricity
supply companies must be observed.
• If using the extension for the coupling rod, do not use the provided drilling
template.
• We reserve the right to make changes.
5. Application
Emergency showers are prescribed first aid installations for work stations where
hazardous materials are being handled.
6. Technical specifications
Minimum flow pressure: 0.5 bar
Maximum stagnation pressure: 10 bar
Volumetric flow:
0.5 bar flow pressure: 45 l/m
1.0 bar flow pressure: 65 l/m
1.5 bar flow pressure: 80 l/m
2.0 bar flow pressure: 90 l/m
2.5 bar flow pressure: 100 l/m
3.0 bar flow pressure: 110 l/m
Assembly height: Lower edge of shower head (220 ± 10) cm
above floor as per EN 15154 Part 1

- 5 -
ZMI_001_2030019057-FAID0004_#SEN_#AQU_#V2.fm
7. Scope of delivery
8. Dimensions
A: Design with pull rod on right
B: Design with pull rod on left
C: For special designs, see the customer drawing for dimensions
9. Installation example
10. Assembly for actuation from right
☞Important!
Prior to the assembly process, flush the pipework in accordance with DIN 1988.
Mount the emergency shower in accordance with EN 15154 Part 1.
☞The manual actuator of the emergency shower can be plugged.
☞To protect the tiles, use masking tape when marking and drilling. Drill at low speed.
☞Depending on the composition of the wall, special wall plugs may have to be used
(to be provided by the customer).
☞Important!
The internal thread G ¾ for the locally provided water connection may not protrude
from the wall by more than 1 mm, and may not extend into the wall by more than
15 mm.
Pos. Pcs. Name
1 1 Shower head
2 1 Wall bracket
3 1 Ball valve
4 1 Wall plate with sealing plug
5 1 Plug-in socket
6 1 Wall support
7 1 Wall bearing linkage
8 1 Hand actuator and guide post support with plugging option
9 1 Accessories kit:
First aid sign, Mounting set
1 Installation and operating instructions

ZMI_001_2030019057-FAID0004_#SEN_#AQU_#V2.fm
- 6 -
☞For a door leaf width from 1 m, check whether the door frame obstructs the
assembly of the pull rod or wall support.
10.1 Door leaf width up to 1 m:
Place the water connection centrally above the door at a height of 2310 ± 100 mm
above the finished floor.
10.2 Screw in the plug-in socket (a) with an Allen key to form a seal.
10.3 Slide the wall plate (b) onto the plug-in socket (a) and align it.
10.4 Mark the drill holes.
10.5 Align the wall support (c) in accordance with the dimensions and mark the drill holes.
☞Alternatively, use the drilling template.
☞If using the extension for the coupling rod, do not use the provided drilling template.
☞Important!
To assemble the system for actuation on the right, use the indicated drill holes.
10.6 Drill in accordance with these markings.
10.7 Insert the wall plugs.
10.8 Screw on the wall support (c).
10.9 Slide the wall plate (b) onto the plug-in socket (a) as far as the wall and fix in place
with the grub screw (d).
10.10 Screw on the wall plate (b).
10.11 Dismantle the fork head (f) from the valve lever (e).
10.12 Screw in the closed ball valve as far as possible, creating a seal and bringing it into
position as follows:
– The valve axis must point downwards (and not to the ceiling).
– The pivot motion of the valve lever must be aligned so that it is parallel to the
floor.
10.13 Secure the ball valve (h) with the two grub screws (g).
10.14 Mount the wall bearing linkage.
j: Rubber
k: Steel
10.15 Screw the fork head (f) to the coupling rod (l).
10.16 Mount the fork head (f) with the coupling rod to the valve lever (e).
10.17 Place the guide post (m) onto the guide (o) on the manual actuator and secure with
the grub screw (n).
10.18 Place the valve lever into the "close" position.
A: Closed
B: Open
10.19 Screw the manual actuator (q) into the fork head (p) of the deflection lever and lock
with a nut.
10.20 Using the spirit level, align the manual actuator (q) so that it is vertical.
10.21 Mark drill holes for the wall support (r) 40 mm above the triangular handle.

- 7 -
ZMI_001_2030019057-FAID0004_#SEN_#AQU_#V2.fm
10.22 Drill in accordance with these markings.
10.23 Insert the wall plugs.
10.24 Screw on the wall support (r).
10.25 Mount the wall arm in a sealing manner and bring it into position.
10.26 Screw the shower head (n) onto the wall arm (m) so that it seals.
10.27 Establish the water connection.
10.28 Check the water connection for leaks.
10.29 Plug the manual actuator if need be.
11. Assembly for actuation from left
☞Important!
Prior to the assembly process, flush the pipework in accordance with DIN 1988.
Mount the emergency shower in accordance with EN 15154 Part 1.
☞The manual actuator of the emergency shower can be plugged.
☞To protect the tiles, use masking tape when marking and drilling. Drill at low speed.
☞Depending on the composition of the wall, special wall plugs may have to be used
(to be provided by the customer).
☞Important!
The internal thread G ¾ for the locally provided water connection may not protrude
from the wall by more than 1 mm, and may not extend into the wall by more than
15 mm.
☞For a door leaf width from 1 m, check whether the door frame obstructs the
assembly of the pull rod or wall support.
11.1 Door leaf width up to 1 m:
Place the water connection centrally above the door at a height of 2310 ± 100 mm
above the finished floor.
11.2 Screw in the plug-in socket (a) with an Allen key to form a seal.
11.3 Slide the wall plate (b) onto the plug-in socket (a) and align it.
11.4 Mark the drill holes.
11.5 Align the wall support (c) in accordance with the dimensions and mark the drill holes.
☞Alternatively, use the drilling template.
☞If using the extension for the coupling rod, do not use the provided drilling template.
☞Important!
To assemble the system for actuation on the right, use the indicated drill holes.
11.6 Drill in accordance with these markings.
11.7 Insert the wall plugs.
11.8 Screw on the wall support (c).
11.9 Slide the wall plate (b) onto the plug-in socket (a) as far as the wall and fix in place
with the grub screw (d).

ZMI_001_2030019057-FAID0004_#SEN_#AQU_#V2.fm
- 8 -
11.10 Screw on the wall plate (b).
11.11 Dismantle the fork head (e) from the valve lever (f).
11.12 Screw in the closed ball valve as far as possible, creating a seal and bringing it into
position as follows:
– The valve axis must point upwards (and not to the floor).
– The pivot motion of the valve lever must be aligned so that it is parallel to the
ceiling.
11.13 Secure the ball valve (h) with the two grub screws (g).
11.14 Mount the wall bearing linkage.
j: Rubber
k: Steel
11.15 Screw the fork head (e) to the coupling rod (l).
11.16 Mount the fork head (e) with the coupling rod to the valve lever (f).
11.17 Place the guide post (m) onto the guide (o) on the manual actuator and secure with
the grub screw (n).
11.18 Place the valve lever into the "close" position.
A: Closed
B: Open
11.19 Screw the manual actuator (q) into the fork head (p) of the deflection lever and lock
with a nut.
11.20 Using the spirit level, align the manual actuator (q) so that it is vertical.
11.21 Mark drill holes for the wall support (r) 40 mm above the triangular handle.
11.22 Drill in accordance with these markings.
11.23 Insert the wall plugs.
11.24 Screw on the guide.
11.25 Mount the wall arm in a sealing manner and bring it into position.
11.26 Screw the shower head (s) onto the wall arm (t) so that it seals.
11.27 Establish the water connection.
11.28 Check the water connection for leaks.
11.29 Plug the manual actuator if need be.
12. Function
12.1 Pull the manual actuator.
• The water will flow.
☞The valve is not self-closing!
12.2 Place the manual actuator back in its start position.
• The water stops flowing.

- 9 -
ZMI_001_2030019057-FAID0004_#SEN_#AQU_#V2.fm
13. Maintenance and care
Check the emergency shower once a month to make sure that it is in working order.
(Guidelines for Laboratories BGI/GUV-I 850-0)
As a measure for the prevention of microbiological contamination, it is recom-
mended that you replace the fill water in the fitting at shorter intervals by opening the
valve.
Use suitable cleaning agents which do not attack the tap in a proper manner and
rinse with water after use. High-pressure cleaners must not be used for cleaning.
14. Troubleshooting
If you cannot rectify a fault or if it is not in the list, please contact our customer
service department!
15. Spare parts
Description Order No.
Ball valve . . . . . . . . . . . . . . . . . . . . . 2030025022
Other spare parts on request; see the wall bracket for material numbers.
Fault Cause Remedy
Water does not flow – Water supply interrupted ➯Restore it
Manual actuator is
catching
– Ball valve not correctly aligned ➯Align it
– Pull rod or manual actuator bent ➯Straighten it
– Ball valve stiff ➯Replace it
Body shower is
dripping
– Ball valve defective ➯Replace it

ZMI_001_2030019057-FAID0004_#SPL_#AQU_#V2.fm
- 10 -
0Polski
Prysznic bezpieczeństwa z drążkiem pociągowym
Patrz rysunek w niemieckiej instrukcji montażu i obsługi.
0Spis treści
1. Skróty i jednostki . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2. Objaśnienie symboli . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3. Gwarancja . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4. Ważne uwagi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Opis produktu
5. Zastosowanie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6. Dane techniczne. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
7. Zakres dostawy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
8. Wymiary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
9. Przykład instalacji . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Montaż, działanie i uruchomienie
10. Montaż z obsługą po prawej stronie . . . . . . . . . . . . . . . . . . . . . . . 12
11. Montaż z obsługą po lewej stronie . . . . . . . . . . . . . . . . . . . . . . . . 14
12. Działanie. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Konserwacja
13. Konserwacja i czyszczenie. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
14. Usuwanie usterek . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
15. Części zamienne . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
1. Skróty i jednostki
EA-Nr. Europejski numer artykułu
Best.-Nr. Nr katalogowy Aquarotter
Przeliczanie jednostek 1 mm = 0,03937 cala
1 cal = 25,4 mm
Wszystkie długości na rysunkach podano w mm.
PL