Franke Frames CM FS 45 BK User manual

CM FS 45 BK
EN Installation and user manual Built-in coffee machine
PL Instrukcja montażu i obsługi Ekspres do kawy do zabudowy
CZ Montážní a servisní návod Vestavěný kávovar
UK Посібник зі встановлення й експлуатації Вбудована кавомашина
RU Руководство по установке и обслуживанию Встраиваемая кофемашина


TABLE OF CONTENTS
Introduction 2
About this manual 2
Safety information 2
Proper installation and placement 2
Proper use 3
Maintenance and cleaning 3
Information for european markets 3
Overview 4
Description 4
Control panel 5
Menu options 6
Installation 11
Operation 12
Switching on the first time 12
Preparing coffee (using coffeebeans) 13
Suggestions 13
Cleaning and care 18
Displayed messages 21
Troubleshooting 22
Faults table 22
Technical data 24
Disposal 24

– 2 –
CM FS 45 BK
EN
INTRODUCTION
This coffee machine will make delicious cups of
coffee, espresso and cappuccino. You can customise
the settings of the machine to suit your personal
preferences and tastes.
Coffee has been used in the factory to test the
appliance and it is therefore completely normal that
there are traces of coffee in the mill. This appliance
is however guaranteed to be new.
ABOUT THIS MANUAL
This user manual applies to several models of the
device. Thus it may be possible that some of the
described features and functions are not available on
your specific model.
FRANKE reserves the right to make modifications
to the product without prior notice. All information
correct at time of issuance.
Carefully read the user manual before using the
device.
Keep the user manual.
Use the device described in this user manual only
according to the intended use.
Symbol Meaning
Warning symbol. Warning against risks of
injury.
Warning symbol. Electrical appliance.
Actions in safety and warning notes to avoid
injury or damage.
Action step. Specifies an action to be done.
Result. Result of one or more action steps.
9Precondition that has to be fulfilled before
performing the following action.
SAFETY INFORMATION
This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning use of
the appliance by a person responsible for
their safety.
Children should be supervised to ensure that
they do not play with the appliance.
The manufacturer can not be made liable for
possible damage which may occur due to
incorrect installation and incorrect, improper
or unreasonable use of the device.
Proper installation and placement
This is an household appliance only.
It is not intended to be used in: staff kitchen
areas in shops, offices and other working
environments; farm houses; by clients in
hotels, motels and other residential type
environments; bed and breakfast type
environments.
This appliance is intended for domestic use
only (around 3000 cups a year). Any other
use is considered improper and in that case
no guarantee will be given.
This appliance can be installed over a built-in
oven if the latter is fitted with a cooling fan
at the rear.
If the plug or power cable is damaged, it
must be replaced by customer services only
to avoid all risk.
Only ask for original spare parts to be used.
Failure to respect the above could reduce
the safety of the appliance.

– 3 –
CM FS 45 BK EN
Risk of burns!
The surface of the heating element remains
hot after use and the outside of the
appliance may retain the heat for several
minutes depending on use.
When using the appliance, do not touch the
hot surfaces. Use the knobs or handles.
In case of failures:
– Make sure the appliance is not
connected to the mains power supply.
– Turn the main power switch on the right
side (behind the front panel) to 0.
– Refer to our service department for
repairs.
Proper use
This appliance is designed to “make
espresso coffee” and “heat drinks”. Use it
with care to avoid scalds from the water
and steam jets or through incorrect use.
Do not lean or hang on the machine when
it has come out of the cabinet and do not
place heavy or unstable objects on the
machine.
Do not put objects containing liquids,
inflammable or corrosive materials on the
machine.
Use the accessories holder to contain
coffee accessories (for example coffee
beans).
Never touch the appliance with damp
hands.
Unplug directly from the plug only.
Never pull the power cable as you could
damage it.
To disconnect the appliance completely,
place the main switch on the side of the
appliance in the 0 (off) position.
Models with glass surfaces:
Do not use the appliance if the surface is
cracked.
Maintenance and cleaning
Cleaning and user maintenance shall not
be made by children without supervision.
Never immerse the appliance in water.
CAUTION: To prevent damage to the
appliance do not use alkaline cleaning
agents when cleaning, use a soft cloth and
a mild detergent.
Appliances with removable cord: avoid
splashes of water on the power cord
connector or socket at the back of the
appliance.
Clean all the components thoroughly,
taking particular care with parts in contact
with coffee and milk.
Information for european markets
This appliance can be used by
children aged from 8 years and above
if they have been given supervision or
instruction concerning use of the appliance in
a safe way and if they understand the hazard
involved. Cleaning and user maintenance
shall not be made by children unless they are
older than 8 and supervised.
Keep the appliance and its cord out of the
reach of children aged less than 8 years.
Appliances can be used by persons with
reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given
supervision or instruction concerning
use of the appliance in a safe way and
understand the hazards involved.
Children shall not play with the appliance.
When not in use and before cleaning,
always unplug the appliance.
Risk of burns!
Surfaces become hot during use.

– 4 –
CM FS 45 BK
EN
OVERVIEW
Description
A. Main switch / Aa. On/Stand-by button
B. Handles
C. Nozzle
D. Water tank (removable)
E. Cup tray
F. Drip tray grill (removable)
G. Service door
H. Height adjustable coffee dispenser
I. Control panel
J. Coffee bean holder cover
K. Ground coffee chute cover
L. Brewing unit
M. Power cable
N. Milk container:
N1. Cover (removable)
N2. Slider Caffe latte/Cappucino (removable)
N3. Clean button
N4. Milk dispenser pipe (removable)
N5. Suction pipe (removable)
O. Hot water spout (removable)
P. Measuring spoon for preground coffee
Q. Waste coffee container (can be taken out)
R. Knob for setting the grind level
S. Coffee bean container
T. Place for the measuring spoon
U. Filling chute for preground coffee
V. Coffee guide
W. Place for accessories (left and right)
X. IEC Connector

– 5 –
CM FS 45 BK EN
Control panel
1. Display
2. Touch key (Coffee strength) to select strength or preground
3. Touch key to select the type/quantity of coffee
–ESPRESSO
–MEDIUM CUP
–LARGE CUP
4. Touch key (One cup of coffee)
5. Touch key (OK) to confirm the selected function
6. Touch key (Two cups of coffee)
7. Touch key (Scroll) to scroll backwards through the menu and display
8. Touch key (Hot water)
9. Touch key (Scroll) to scroll forwards through the menu and display
10. Touch key (Menu) to activate or deactivate menu
11. Touch key (Return) to exit the selected mode
12. Touch key (Cappuccino)
13. Touch key (Latte macchiato)

– 6 –
CM FS 45 BK
EN
Menu options
You can change the following menu options and
functions:
– Rinsing
– Set language
– Energy saving (enable or disable energy saving)
– Set time (daytime)
– Auto start (auto switch on)
– Auto off (auto turn off)
To go back to the coffee mode:
Press the touch key (11).
Rinsing
If 2/3 minutes have passed, since you last made coffee, you should first rinse
the system to preheat the brewing unit. Select the rinsing function from the
appropriate menu. Let the water run into the drip tray underneath. You can
also use this water to warm up the cup that you are using for the coffee.
In this case simply let the hot water run into the cup (and then empty it).
Press the touch key (10) to enter the menu.
Press the touch keys (7and 9) until RINSING is displayed.
Press the touch key (5) to confirm. RINSING PRESS OK is displayed.
Press the touch key (5) again to confirm.
The appliance performs an automatic rinse cycle (a little hot water runs out
of the spouts and is collected in the drip tray beneath).
Set language
You can choose between several languages. A different language can be
selected as follows:
Press the touch key (10) and press the touch keys (7and 9) until
the menu option SET LANGUAGE appears. Confirm the menu option with
the touch key (5).
The language set appears on the display. Press the touch keys (7and 9)
until the desired language appears. When the desired language is displayed,
confirm with the touch key (5).
Energy saving
Use this function to enable or disable Energy saving.
To enable or disable the function, proceed as follows:
Press the touch key (10) and press the touch keys (7and 9) until
the menu option ENERGY SAVING appears.
Confirm the menu option with the touch key (5).
DISABLE? is displayed (or ENABLE? if the function has already been
disabled). Confirm with the touch key (5).
When enabled, the function reduces energy consumption in compliance with
European regulations.
– Set temperature (of the water to make coffee)
– Water hardness
– Contrast (display)
– Buzzer
– Statistics (from the appliance)
– Default values (reset)
– Descale

– 7 –
CM FS 45 BK EN
Set time
To adjust the time on the display, proceed as follows:
Press the touch key (10) and use the touch keys (7and 9) until
SET TIME is displayed. Press the touch key (5).
The hours flash on the display.
Use the touch keys (7and 9) to set the hour, then press the touch
key (5) to confirm. The minutes flash on the display.
Use the touch keys (7and 9) to set the minutes. Then press the
touch key (5) to confirm.
Press the touch key (11) to exit the menu.
Auto start
You can set the auto start time in order to have the appliance ready at a certain
time (for example in the morning) so you can make coffee immediately.
CAUTION! To enable this function, the time must be set correctly.
Press the touch key (10) to enter the menu and then the touch
keys (7and 9) until AUTO START is displayed.
Press the touch key (5). ENABLE? is displayed.
Press the touch key (5). The hours flash on the display.
Use the touch keys (7and 9) to set the hour.
Press the touch key (5) to confirm. The minutes flash on the display.
Use the touch keys (7and 9) to set the minutes.
Press the touch key (5) to confirm. ENABLED appears under AUTO START.
Press the touch key (11) to exit the menu.
Disable auto start
Press the touch key (10) to enter the menu and then the touch
keys (7and 9) until AUTO START is displayed.
Press the touch key (5). DISABLE? is displayed.
Press the touch key (5). DISABLED is displayed.
Press the touch key (11) to exit the menu.
Auto off (Standby)
The appliance is set by default to go off if not used for 30 minutes. The time
can be changed so that the appliance switches off after 15 or 30 minutes, or
after 1, 2 or 3 hours. To re-programme Auto off, proceed as follows:
Press the touch key (10) and press the touch keys (7and 9) until
the menu option AUTO OFF appears. Confirm the menu option with the
touch key (5).
Select another auto off time with the touch keys (7and 9). When the
desired auto off time is displayed, confirm it with the touch key (5).
Press the touch key (11) to exit the menu.

– 8 –
CM FS 45 BK
EN
Set temperature
There are four temperature levels.
The coffee temperature levels are defined as follows:
The factory setting can be changed as follows:
Press the touch key (10) and press the touch keys (7and 9) until
the menu option SET TEMPERATURE appears.
Confirm the menu option with the touch key (5). The display shows the
current setting.
Select another temperature with the touch keys (7and 9). When the
desired temperature is displayed, confirm it with the touch key (5).
Press the touch key (11) to exit the menu.
Water hardness
A DESCALE! message is displayed after the appliance has been operated for a
factory set period of time, calculated on the basis of the maximum quantity of
lime scale which may be contained in the water used. If necessary, this period
of operation can be extended, making descaling less frequent, by programming
the appliance based on the actual lime content in the water used.
Proceed as follows:
Remove the “Total Hardness Test” strip (in front of your manual) and dip it
fully in the water for a few seconds.
Remove it and wait 30 seconds until its colour changes and a number of
red dots are formed. For example, if there are 3 red dots on the test strip,
you must set the water hardness level to 3.
Note: If you no longer have a water hardness test, you can find the data in the
table below.
Press the touch key (10) and press the touch keys (7and 9) until
the menu option WATER HARDNESS appears. Confirm the menu option
with the touch key (5).
The display shows the current setting.
Press the touch keys (7and 9) until the established hardness level is
displayed. Confirm the selection with the touch key (5).
The appliance is now programmed to provide the descaling warning when
necessary, based on the actual hardness of the water.
Note: Information on the hardness of the water in your area can be obtained
from the local water board. The table below shows the water hardness setting
your machine requires.
German
hardness
French hardness Water hardness
machine
0 - 6 dH 0 - 11 fH
7 - 13 dH 12 - 17 fH
14 - 20 dH 18 - 36 fH
> 21 dH > 37 fH

– 9 –
CM FS 45 BK EN
Adjust contrast
To increase or reduce the contrast of the display, proceed as follows:
Press the touch key (10) to enter the menu and then the touch
keys (7and 9) until CONTRAST is displayed.
Press the touch key (5) to confirm.
Press the touch keys (7and 9) until the required display contrast is
reached. The progressive bar indicates the level of contrast selected:
Press the touch key (5) to confirm.
Press the touch key (11) once to exit the function or twice to exit the
menu.
Buzzer
You can activate or deactivate the buzzer emitted by the machine each
time an icon is pressed or an accessory is inserted/removed.
Press the touch key (10) to enter the menu and then the touch
keys (7and 9) until BUZZER is displayed.
Press the touch key (5) to confirm.
DISABLE? is displayed (or ENABLE? if the function has already been
disabled). Press the touch key (5) to confirm.
Statistics
Proceed as follows to look up the values:
Press the touch key (10) and press the touch keys (7and 9) until
the menu option STATISTICS appears.
Confirm the menu option with the touch key (5). By pressing the
touch keys (7and 9) you can check:
– how many coffees have been made;
– how many milk drinks have been made;
– how many times the machine has been descaled;
– the total number of litres of water delivered.
Note: Two cups of coffee dispensed at the same time are counted as two cups.
Press the touch key (11) to exit the menu.
Defaut values (reset)
This resets all menu settings and programmed quantities back to the default
values (with the exception of the language which remains as set).
To reset the default values, proceed as follows:
Press the touch key (10) and press the touch keys (7and 9) until
the menu option DEFAULT VALUES appears.
Confirm the menu option with the touch key (5).
The display shows CONFIRM?
Confirm the menu option with the touch key (5).

– 10 –
CM FS 45 BK
EN
Descaling
Over time, leads the continuous heating of the water that is used to make
coffee to lime deposits in the inner circuits of the machine. Descale the
machine when the message DESCALE flashes on the display.
Use the descaler recommended by the manufacturer only. Under no
circumstances should you use sulphamic or acetic based descalers.
Their use invalidates the guarantee.
Descale the appliance as described.
Insert the hot water spout.
Press the touch key (10) and press the touch keys (7and 9) until
the menu option DESCALE appears. Confirm the menu option with the
touch key (5).
The display shows CONFIRM? Confirm with the touch key (5).
The message ADD DESCALER PRESS OK is displayed.
Empty the tank of water, pour the contents of the descaler bottle (125 ml)
into the tank respecting the instructions given on the descaler pack, then
add 1 liter water. For subsequent descaling operations, descaling solution
can be purchased from authorised technical service centres.
Make sure that any splashes from the descaling product do not come
into contact with surfaces that are sensitive to acids, such as marble,
limestone and ceramic.
9Put an empty container with a capacity of at least 1,5 litres underneath the
coffe spouts and hot water spout.
Press the touch key (5). The display shows DESCALING IN PROGRESS.
The descale program starts and the descaler liquid is delivered first from the
coffee spouts and then from the hot water spout.
– The descale programme automatically performs a series of rinses and
pauses to remove limescale deposits from inside the machine.
– After about 30 minutes, the message RINSING FILL TANK is displayed.
The appliance is now ready for a rinsing process with clean water.
9Empty the container used to collect the descaler solution.
9Take out the water tank, empty the watertank and fill it with clean water.
Put the water tank back in place and put the container back under the coffe
spouts and the hot water spout.
The display shows: RINSING PRESS OK.
Press the touch key (5).
Hot water flows out of the coffee spouts and the message RINSING PLEASE
WAIT is displayed.
Once the rinsing is finished, the message RINSING FILL TANK is displayed.

– 11 –
CM FS 45 BK EN
9Empty the container used to collect the water used for rinsing.
9Take out the water tank, empty the watertank and fill it with clean water.
9Put the water tank back in place and put the container back under the coffe
spouts and the hot water spout. The display shows: RINSING PRESS OK.
Press the touch key (5).
Hot water flows out of the hot water spout.
Once the rinsing is finished, the display shows RINSING COMPLETE PRESS OK.
Press the touch key (5).
The appliance goes off automatically.
Note: If the descaling cycle is interrupted before completion, the appliance
continues to display the descale message and the program must be
started again from the beginning.
Failure to descale the appliance invalidates the guarantee.
INSTALLATION
IMPORTANT
After removing the packaging, make sure the
product is complete and undamaged. If in doubt,
do not use the appliance and contact a qualified
professional.
Installation must be carried out by a qualified
techncian and in compliance with current
regulations.
Packing elements (plastic bags, polystyrene etc.)
must not be left within reach of children as they
may represent a hazard.
Never install the appliance in environments where
the temperature may reach 0 °C or lower (the
appliance may be damaged if the water freezes).
Make sure the mains voltage corresponds to the
voltage indicated on the appliance rating plate.
Connect the appliance to an efficiently earthed
socket with a minimum current rating of 10A only.
The manufacturer may not be considered liable
for possible incidents caused by the failure to
adequately earth the mains.
Make sure the socket used is freely accessible at
all times, enabling the appliance to be unplugged
when necessary.
Never touch the plug with damp hands.
Never pull the power cable as you could damage it.
This appliance can be installed over a built-in oven
it he latter is fitted with a cooling fan at the rear
(maximum power: 3KW).
Do not use multiple plug adapters or extension
leads.
The power cable on this appliance must not be
replaced by the user as this operation requires
the use of special tools. If the cable is damaged or
requires replacing, contact an authorised service
centre only to avoid all risks.
You should personalise water hardness as soon as
possible following the instructions.
Building in
Please check the minimum measures necessary
to the proper installation of the appliance. The
coffee maker must be installed in a column unit,
which must in turn be fixed to the wall (Fig. 1,
page 25).
Position the appliance on the rail, making sure the
pins are correctly inserted in the housing, then fix
it with the screws supplied (Figure 4).
If the height of the appliance requires adjusting,
use the spacer disks provided.

– 12 –
CM FS 45 BK
EN
OPERATION
Switching on the first time
Connect the appliance to the mains supply (see
chapter Installation) and switch on the appliance
with the main switch (see A page 4).
The first time you switch on the appliance with
the main switch and every time that it is plugged
in, the appliance executes a SELF-DIAGNOSIS
action.
Then the appliance switches off.
To turn it on, press the On/Stand by button (Aa)
on the left site underneath the control panel.
IMPORTANT
Coffee has been used to factory test the
appliance and it is therefore completely normal
for there to be traces of coffee in the mill.
Customise water hardness as soon as possible
following the instructions in the “Setting water
hardness” section.
When using the appliance for the first time,
you need to make 4-5 cups of coffee and
4-5 cappuccinos before the appliance gives
satisfactory results.
Each time you turn the coffee maker on by the main
switch (A), it performs a SELF-DIAGNOSIS cycle
and then goes off. To turn it on again, press the On/
Stand by button (Aa).
Start the appliance with the On/Stand by button
(see ‘Aa’). The appliance displays FILL TANK in
different languages.
9Extract the water tank, rinse and fill with fresh
water without exceeding the MAX line.
9Replace and push as far as it will go.
Set the required language.
When the message PRESS OK TO SET TO
ENGLISH is displayed, press and hold the touch
key (5) for about 5 sec.
– If you set the wrong language, follow the
instructions in the “Setting the language”
section.
– If your language is not available, select
one from those displayed. The instructions
refer to the English version. Then follow the
instructions displayed.
Place a cup under the hot water spout. If the hot
water spout is not inserted.
The appliance displays INSERT WATER SPOUT.
Place the hot water spout if it is not there.
The appliance displays: HOT WATER PRESS OK.
Press the touch key (5) and after a few
seconds a little water comes out of the spout.
The machine now displays TURNING OFF PLEASE
WAIT and goes off.
Extract the appliance by pulling it out using the
handles.
Open the lid and fill the container with coffee
beans, then close the lid and push the appliance in.
The coffee maker is now ready for normal use.

– 13 –
CM FS 45 BK EN
IMPORTANT
Only fill the water tank with cold water. Never use
other liquids such as mineral water or milk.
To prevent malfunctions, never fill with ground
coffee, frozen or caramelised coffee beans or
anything else that could damage the appliance.
Preparing coffee (using coffeebeans)
The appliance is preset to make coffee with a normal
taste. You can also choose coffee with an extra mild,
mild, normal, strong or extra-strong taste. There is
also a pre-ground coffee option.
9To choose the required taste, press more times
the touch key (2).
The required coffee taste is displayed.
9Place 1 cup under the spouts to make 1 coffee or
2 cups for 2 coffees.
9Lower the spouts as near as possible to the cup
for a creamier coffee.
9Press the touch key (3) to select the type of
coffee:
– ESPRESSO
– MEDIUM CUP
– LARGE CUP
9Press the touch key (4) if you want to make
one coffee and the touch key (6) if you want
to make two coffees.
The appliance now grinds the beans and starts
delivering the coffee into the cup.
Once the set amount of coffee has been delivered,
the machine stops delivery automatically and
expels the exhausted waste coffee into the
waste coffee container. After a few seconds, the
appliance is ready for use again.
Suggestions
To turn the appliance off, press the ON-OFF
button (Aa / see page 4). Before going off, the
appliance performs an automatic rinse cycle. Take
care to avoid scalds.
If the coffee only comes out in drips or not at all,
the knob for setting the grind level must be turned
by one position clockwise (see Setting the grind
level). Turn one click at a time until the coffee is
delivered satisfactorily.
If the coffee comes out too fast and the cream
does not meet your taste, turn the knob by one
position anti-clockwise). Make sure that you
do not turn the knob for setting the grind level
too far, as coffee may come out in drips when
dispensing 2 cups.
You can stop the coffee from dispensing by
pressing the touch key (4) or touch key
(6) again.
After the coffee has finished dispensing (the
progress bar reaches 100%), you can change the
amount of coffee (see Changing the quantity of
coffee).
When the display shows the message FILL TANK!,
you must fill the tank, otherwise the appliance
cannot make any coffee. It is normal that there
is some water left in the water tank when the
message is displayed.
Tips to make hotter coffee
After 3 minutes since you last made coffee, you
can preheat the brewing unit by using the menu
setting RINSING (see Rinsing).
Run off the water into the underlying drip tray or
alternatively use this water to fill (and then empty)
the cup to be used for the coffee.
Do not use cups that are too thick, as they will
absorb too much heat.

– 14 –
CM FS 45 BK
EN
Empty the waste coffee container
– The appliance counts the number of coffees
made. Every 14 single coffees (or 7 doubles)
the appliance displays EMPTY WASTE COFFEE
CONTAINER. This means that the waste coffee
container is full and must be emptied and
cleaned.
As long as the waste coffee container is not
cleaned, this message remains in place and the
coffee machine cannot make any coffee.
To clean, open the service door at the front by
pulling the coffee spout, remove the drip tray,
empty it and clean it.
CAUTION Always completely extract the
drip tray, to avoid that it falls when removing
the grounds container. Empty the grounds container
and clean thoroughly, making sure all residues
deposited on the bottom are removed.
Every time you pull the drip tray out, the waste
coffee container must also be emptied, even if it
is not completely full. If this process is not carried
out, the waste coffee container may overfill when
coffee is made and the machine may get blocked.
Never remove the water tank when the appliance
is dispensing coffee. Otherwise, the appliance will
not be able to make the coffee.
If the appliance malfunctions, do not contact
the service centre straight away, but first look at
the troubleshooting guide. If this does not help,
contact the customer service.
Changing the quantity of coffee
The appliance is factory preset to automatically
deliver the following quantities of coffee:
– ESPRESSO
– MEDIUM CUP
– LARGE CUP
To change these quantities, proceed as follows:
Place a cup under the spouts.
Press the touch key (3) to select the type of
coffee.
Keep the touch key (4) pressed until the
message PROGRAM QUANTITY is displayed and
coffee delivery begins.
As soon as the coffee in the cup reaches the
required level, press the same icon again. The
quantity set has now been programmed.
Setting the grind level
If coffee is dispensed too quickly or
too slowly (in drips), you can change
the grind level.
CAUTION Only change
the grind level during the
milling process. Otherwise, the
coffee machine may be damaged.
Extract the appliance by pulling
it out using the handles.
Press the touch key (4).
Open the coffee bean holder cover.
Turn the knob for setting the grind level
anti-clockwise to obtain finer ground coffee,
slower delivery and a creamier appearance.
Turn the knob clockwise for
coarser ground coffee and faster
delivery (not a drop at a time).
The adjustment will be evident
after at least 2 cups of coffee
are made.

– 15 –
CM FS 45 BK EN
Preparing espresso coffee using ground coffee
Press the touch key (2)
several times to select PRE-
GROUND.
Extract the machine by pulling it
outwards using the handles.
Lift the central lid, place one
measure of preground coffee in the funnel, push
the appliance back and proceed as described in
the section „Making coffee using coffee beans”.
You can make just one coffee at a time by
pressing the touch key (4).
After using the machine with pre-ground coffee,
to go back to making coffee using beans,
deactivate the pre-ground coffee function by
pressing the touch key (2).
IMPORTANT
– Never introduce pre-ground coffee when the
machine is off or it could spread through the
inside of the appliance.
– Never add more than 1 measure, otherwise the
appliance will not make the coffee.
– Use the measure provided only.
– Introduce only pre-ground coffee for espresso
coffee machines into the funnel.
– If more than one measure of pre-ground coffee is
used and the funnel clogs, push the coffee down
with a knife. Then remove and clean the brewing
unit and machine as described in the “Cleaning
the brewing unit” section.
Preparing hot water
Hot water can be used to warm up cups and to make
hot drinks, such as tea or packet soups.
Only activate the hot water spout when
there is a receptacle underneath it. Escaping
hot water can lead to scalds!
Put the hot water spout in place.
Place a container underneath
the hot water spout.
Press the touch
key (8). Hot water is
dispensed.
The display shows HOT WATER.
Once the programmed amount of hot water is
dispensed, dispensing stops automatically. For
a few seconds the display shows PREPARATION
RUNNING. After that the appliance is ready to
make coffee again and the last selected coffee
setting appears on the display.
Changing the quantity of hot water
The machine is set by default to automatically
delivery 150 ml of hot water. To change these
quantities, proceed as follows:
Place a container underneath
the water spout.
Keep the touch key (8)
pressed until the message
PROGRAM QUANTITY is
displayed and hot water delivery
begins.
As soon as the hot water in the cup reaches the
required level, press the same icon again.
The quantity set has now been programmed.
Making cappuccino
This feature allows you to make cappuccino. To do this,
use the special milk container.
Rinse the milk container under the tap when you
use it for the first time.
Select the taste of the coffee you want to use to
make the cappuccino by pressing the touch
key (2).
Remove the lid of the milk container.
Fill the container with about 100 grams of milk for
each cappuccino to be prepared.
– Never exceed the MAX level (corresponding to
about 750 ml) marked on the container.
– You should ideally use skimmed or semi skimmed
milk at refrigerator temperature (about 5°C).

– 16 –
CM FS 45 BK
EN
– Make sure the intake tube is correctly inserted in
the rubber washer.
Then replace the milk container lid.
– The quantity of froth can be adjusted by moving
the regulator to CAPPUCCINO or CAFFE LATTE:
– CAFFE LATTE for a denser froth;
– CAPPUCCINO for a less dense froth.
Remove the hot water spout and attach the milk
container to the nozzle.
Position the milk spout (N4) and then place a
sufficiently large cup under the coffee and milk
spouts.
Press the touch key (12). CAPPUCCINO is
displayed and after a few seconds, frothed milk
flows out of the milk spout into the cup below
(delivery stops automatically).
Next the appliance delivers coffee.
The cappuccino is now ready. Sweeten to taste
and, if desired, sprinkle the froth with a little cocoa
powder.
Making Latte Macchiato
Prepare the appliance as described in ‘Making
cappucino’.
Position the froth regulator (N2) between
CAPPUCCINO and CAFFE LATTE printed on the
milk container lid.
Press the touch key (13).
Frothing milk
First, prepare the appliance as
described in ‘Making cappucino’,
step 2, 3, 4, 5 and 6.
Press the touch key (12)
or (13) twice (within two
seconds).
The quality of frothed milk
delivered is equal to that of the selected drink
(cappuccino or latte macchiato).
Notes:
– While making cappuccino or latte macchiato, the
flow of frothed milk or coffee can be interrupted
by pressing the touch key (12) or the
touch key (13).
– If the milk in the container finishes while
delivering frothed milk, remove the container and
add milk. Then re-attach it and press the
touch key (12) or the touch key (13) to request
cappuccino again.
To ensure the complete cleanliness and hygiene
of the milk frother, always clean the circuits in
the milk container lid after making cappuccino.
PRESS CLEAN! flashes on the display.
Place a recipient under the milk
spout.
Press the CLEAN button on the
lid (N3) and hold down for at least
5 seconds to start the cleaning
function. The appliance displays
the message CLEANING above a
progressive bar.
You should not release the CLEAN button until
the bar is complete indicating that cleaning is
concluded. When the CLEAN button is released,
the function stops.
After cleaning, remove the milk container and place
in the refrigerator. The milk should not be left out of
the refrigerator for more than 15 minutes.
To change the quantity of coffee or frothed milk
the appliance delivers automatically into the cup,
proceed as described in the section “Changing
the quantity of coffee and milk for cappuccino or
latte macchiato”.

– 17 –
CM FS 45 BK EN
Changing the quantity of milk and coffee for
cappuccino or latte macchiato
The appliance is set by default to automatically
deliver a standard cappuccino or latte macchiato.
To change these quantities, proceed as follows:
Fill the container with milk up to the maximum level.
Hold the touch key (12) until the message
MILK FOR CAPPUCCINO PROGRAM QUANTITY
is displayed or hold the (13) touch key until
the message MILK FOR MACCHIATO PROGRAM
QUANTITY is displayed.
Release the touch key. The appliance starts
delivering milk.
Once the required quantity of milk has been delivered
into the cup, press the touch key (12) or (13)
touch key again. After a few seconds, the appliance
starts delivering coffee into the cup and the message
COFFEE FOR CAPPUCC. PROGRAM QUANTITY or
COFFEE FOR MACCHIATO PROGRAM QUANTITY is
displayed.
Once the required quantity of coffee has been
delivered into the cup, press the touch key (12)
or (13) touch key again. Coffee delivery stops.
The machine is now reprogrammed with the new
milk and coffee quantities.
Cleaning the spouts
Clean the spouts on the milk container every time
after heating milk or making cappuccino. Otherwise,
remains of milk may set hard.
Place a container under the milk
dispenser pipe and press on the
CLEAN button (N3) on the milk
container for at least 5 seconds.
The display shows CLEANING!
Risk of scalding from steam and hot water
escaping from the milk dispenser pipe.
Remove the milk container and clean the spouts
on the appliance with a damp cloth.
Put the hot water spout back in.
Note: After you finished cleaning, remove the milk
container and place it in the fridge, as the milk should
not stay out of the fridge for longer than 15 minutes.
See “Cleaning the spouts and the milk container” for
information on cleaning the milk container.

– 18 –
CM FS 45 BK
EN
CLEANING AND CARE
Before performing any
cleaning operations,
the machine must be turned off
by pressing the main switch (A)
and unplugged from the mains
power supply. Never immerse
the coffee maker in water.
Cleaning the coffee machine
Do not use solvents or abrasive detergents to
clean the coffee maker. A soft damp cloth will
suffice.
Never wash any of the components of the coffee
maker in the dishwasher.
The following parts of the machine must be cleaned
regularly:
– Waste coffee container (Q).
– Drip tray (F).
– Water tank (D).
– Coffee spouts (H).
– Pre-ground coffee funnel (U).
– Inside of the machine, accessible after opening
the service door (G).
– Brewing unit (L).
Cleaning the waste coffee container (Q)
When EMPTY WASTE COFFEE CONTAINER is
displayed, the waste coffee container must be
emptied and cleaned.
To clean:
Open the service door on the front of the
appliance, extract the drip tray and clean.
Clean the waste coffee container thoroughly.
IMPORTANT! When extracting the drip tray, the
waste coffee container must always be emptied.
Cleaning the drip tray (F)
IMPORTANT! If the drip tray is not emptied the water
might overflow. This could damage the machine. The
drip tray is fitted with a level indicator (red) showing
the level of water it contains. Before the indicator
protrudes from the cup tray, the drip tray must be
emptied and cleaned.
To remove the drip tray (F):
Open the service door.
Remove the drip tray and
the waste coffee container.
Clean the drip tray and
waste coffee container.
Replace the drip tray and
waste coffee container.
Close the service door.
Cleaning the water tank (D)
Clean the water tank regularly (about once a
month) with a damp cloth and a little mild washing
up liquid.
Remove all traces of washing up liquid.
Cleaning the spouts
Clean the spouts periodically using a sponge.
Check regularly that the holes in the coffee spout
are not blocked. If necessary, remove coffee
deposits with a toothpick.
Milk residues left on the nozzle (N) and in the
container may jeapardise correct operation of the
appliance.
Each time you use the coffee maker, they must
therefore be removed by cleaning the nozzle with
a sponge.
Table of contents
Languages:
Other Franke Coffee Maker manuals

Franke
Franke A800 User manual

Franke
Franke SAPHIRA User manual

Franke
Franke Spectra S User manual

Franke
Franke COMPACT T 400 Operation instructions

Franke
Franke A600 User manual

Franke
Franke SPECTRA X User manual

Franke
Franke Flair User manual

Franke
Franke SPECTRA I User manual

Franke
Franke T 200 User manual

Franke
Franke A300 Configuration guide

Franke
Franke PURA PRONTO User manual

Franke
Franke A800 User manual

Franke
Franke SPECTRA X User manual

Franke
Franke bremer VIVA User manual

Franke
Franke Flair User manual

Franke
Franke S700 User manual

Franke
Franke MYTICO DUE User manual

Franke
Franke Evolution User manual

Franke
Franke S700 User manual

Franke
Franke Flair User manual