Franke Bernadine FF20650 User manual

InstallatIon Manual
BERNADINE
FF20650 Pull-Down Kitchen Faucet
LIMITED LIFETIME WARRANTY
Franke Kitchen Systems, LLC (Franke) extends the following
warranty to the original purchaser of its faucets effective
January 1, 2003.
All faucets installed in a private residencewill carry a limited
lifetime warranty on all mechanical parts to be free of manufacturing
defects in material and workmanship under normal usage. This
faucet is also warranted for outdoor installations for a period of
five (5) years from the original date of purchase. All chrome finishes
carry a limited lifetime warranty; all other finishes are warranted for
five (5) years from the original date of purchase.
This warranty applies only to the original owner, providing the
product has been installed in accordance with our installation
instructions, used as recommended and in a normal residential
application. In the event of a warranty claim, the owner will be
required to provide proof of purchase - save sales receipt. This
warranty covers all components which make the product operational.
Franke, at its option, may repair or replace the product or
components necessary to restore the product to good working
condition. Franke reserves the right to inspect the installation prior
to the actual replacement of the product or component part. This
warranty does not cover misuse or abuse, accidental damages,
scuffs or scratches, improper installation, abnormal usage, negligence
or damage caused by improper maintenance or cleaning. Normal
wear of parts is excluded from the warranty. Damage caused by
impurities or acts beyond our control are not covered. Any product
or part which has been repaired or altered in any manner outside of
Franke’s factory, unless previously authorized in writing by Franke,
will void warranty. Any replacement excludes transportation and
any labor re-installation costs. This warranty does not allow
recovery of incidental or consequential damages such as loss of
use, delay, property damage or other consequential damage,
and Franke accepts no liability for such damages.
The Franke warranty is limited to the above conditions and to the
warranty period specified herein and is exclusive. Franke DISCLAIMS
all other warranties, expressed or implied, including IMPLIED
WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A
PARTICULAR PURPOSE. This warranty gives you specific legal rights
that may vary from state to state.
Further information
For any further information about our products, about the installation
of them or about the guarantee, please contact the customer
service department at:
Franke Kitchen Systems, LLC
Kitchen Systems Division
800 Aviation Parkway
Smyrna, TN 37167
Phone: [phone]
Fax: [phone]
www.franke.us/ks.com
STANDARD MAINTENANCE AND TROUBLESHOOTING
Replacing the Cartridge
1. Shut off the water supply to the faucet
2. Turn on the faucet briefly to relieve any pressure inside the faucet
3. Move the faucet handle to the “OFF” position
4. Remove set screw from handle using an allen key
5. Pull the lever handle F from the faucet body
6. Unscrew the cartridge cap E
7. Unscrew the cartridge nut D
8. Lift ceramic disk cartridge C from the body and replace it with
new cartridge. Ensure the 2 lugs on the bottom of the cartridge
sit properly in the locating holes in the faucet body.
9. Re-assemble faucet in reverse order
10. Test for leakage
General Maintenance
• Cleanaeratorperiodicallyforanybuildup
• Donotuseharshdetergents,solvents,chemicalagents,
especially any containing CHLORINE, or metallic sponges as
these can damage the surface finish
• Cleanonlywithsoftspongeandsoapywater
• ATTENTION! For outdoor installation product must be
protected from freezing temperatures. Disconnect hot and
cold supply hosesfrom home, open the handle to drain out all
water.Cover faucet with protective covering to keep warm.
Spare/Replacement List
A. F205501 Spray Hose Assembly
B. F206501 Spray Head Assembly
C. F206502 Cartridge
D. F3412 Cartridge Nut
E. F205506 Cartridge Cap
F. F206503 Handle Assembly
G. F205508 Fast-In Mounting Kit
H. F205509 Hot Supply Hose
I. F205510 Cold Supply Hose
J. F205511 Spray Supply Hose
K. F205512 Check Valve Holder with Washer
L. F205513 Check Valve
M. F205514 Clip on Weight
N. F205515 Base Plate
O. F205516 Base Plate Gasket
P. F205518 Flat Washer
M.
A.
B.
C. D. E. F.
H. J. I.
N.
P.
O.
K.
L.
G.

TECHNICAL DATA
• Flowrate–1.75gpmat60psi
• Recommendedwaterpressure–30-85psi
• Maxwaterpressure–115psi
• Maxwatertemperature–158F
• Holesizeforfaucet–13 /8"
Note
Contact us immediately if you see inconsistencies:
• Phone–1-800-626-5771
• Email–[email protected]
• Website–www.franke.us/ks.com
Contents in Box
A. Faucet assembly
B. Supply hoses
C. Allen wrench
D. Clip on weight
E. Base plate
F. Base plate gasket
G. Spray hose
INSTALLATION INSTRUCTIONS
1. Remove all contents from the package and check for completeness.
2. Turn off water supply.
3. Removefaucet(1)andhardwarefromitsprotectivepackaging–
faucet comes assembled.
4. Cut mounting hole 13
/8" in diameter (35mm) in the desired
position (if one isn’t available).
5. Remove set screw (2) from faucet body (1) and sit aside for later.
Place a soft cloth in the sink or on the countertop to sit the
faucet (1) on during the installation to protect it from scratches.
6. Separate the Fast-InTM base (3) from the faucet body (1) and slide it
several inches down the attached supply hoses (6,7,8,9).
7. Insert supply hoses (6,7,8,9) and Fast-InTM base (3) into desired
mounting location hole and lay faucet to side on soft cloth. If your
application has 3 holes to cover, sit base plate gasket and base
plate (5) over the holes. If your application is a single hole, the
base plate and gasket (5) are optional.
8. Make sure the rubber o-ring (4) is in the groove at the bottom of
the Fast-InTM base (3). You may have to loosen the phillips screws
at the top of the Fast-InTM base (3) until the mounting cleats are
free which will allow them to tuck inside the Fast-InTM base (3) for
installation. (See Fig 1).
9. Make sure the flat side of the Fast-InTM base (3) that is labeled
"PULL-OUT" (See Fig 2) is facing squarely towards the backsplash
behind your sink, or where you intend to mount the faucet
(See Fig 3). This should allow you to align the Fast-InTM base
(3) properly so the faucet spout and handles are pointed in the
right direction after installed. If you are unsure, slide the faucet
body (1) onto the Fast-InTM base (3) to confirm if the spout and
handles are aligned properly before you tighten the screws.
10. Tighten 2 mounting screws in the Fast-InTM base (3) with phillips
screwdriver to secure the base to the mounting surface. This
will take several turns. If you decide to use a power drill, it is
recommended to apply final torque by hand, not with the drill,
to avoid damaging the screws.
11. Slide faucet body (1) onto the Fast-InTM base (3), align the screw
hole in the faucet body (1) with the hole in the Fast-InTM base (3),
and install and tighten the set screw (2) to secure the faucet
body (1) to the Fast-InTM base (3).
12. Connect the spray hose (9) to the spray supply hose (6) connected
to the faucet body (1).
13. Attach the clip-on weight (10) to the spray hose (9) approximately
2" above the bend in the bottom of the spray hose.
14. Connect the supply hoses (7 & 8) to the water supply in the
home.
15. Remove aerator using a 22mm wrench, turn on water and flush
the faucet for any debris. Check for leaks and reinstall aerator.
(See fig 4).
1.
3.
4.
5.
6.
9.
10.
2"
2.
7.
8.
PULL-OUT
MOUNTING
CLEATS
MOUNTING
CLEATS
G.
E.
D.
A.
B.
F.
C.
Fig 2Fig 1 Fig 4
Squarely align
Pull-out side
Back splash
Fig 3