Franke DVS Safe Ensuite VR01-081-NTH User manual

Page 8
MT04-001 AquariTherm Tap (Manual) www.dartvalley.co.uk
Revision No. MAQTIN16071301
The supplied fixing kit is suitable for fixing the basin on up to
250mm wall thicknesses.
For fixing kits suitable for wall thicknesses deeper than 250mm,
P.O.A.
Safe Ensuite Low Profile Basin
Installation instructions
Dart Valley Systems Ltd | Kemmings Close | Long Road | Paignton | Devon | TQ4 7TW | UK
t [phone] | f+44 (0)1803 559016 | [e-mail] | www.dartvalley.co.uk
Page 4
P P 0 0 - 010 10 1117
P P 0 0 - 010 10 1117
Step 1 : Safety first Step 2 : Parts (Supplied)
These instructions relate to the use of the Low Profile Basin,
any external or ‘add-on’ parts will be supplied with separate
instructions.
IMPORTANT : Please read these instructions carefully
and follow each stage in order!
Drilling template
Waste grid
VR01-032 (x1)
Waste bung
VR01-033 (x1)
1¼” plastic
male iron
PP00-123 (x1)
VR01-081* (basin)
M12 Square
washer (x4)
M12 hex nut
(x4)
M12 All thread
(x4)
Fixing Kit
VR01-021
VR01-081 - NTH
VR01-082 - 1TH L
VR01-083 - 1TH R
VR01-084 - 2TH
Notes :

Page 3
MT04-001 AquariTherm Tap (Manual) www.dartvalley.co.uk
Revision No. MAQTIN16071301
Page 2
MT04-001 AquariTherm Tap (Manual) www.dartvalley.co.uk
Revision No. MAQTIN16071301
Step 4 : Fittings Installation Cleaning
Page 3
This product should be cleaned daily with warm soapy water, then
rinsed with cold water. If desired, this product can be dried using
a soft non-abrasive cloth.
The gel coat has a high gloss surface. Abrasive cleaners and
scouring powders should be avoided, as long term, these
products will scratch and damage the gel coat.
Non abrasive cleaning agents can be used, however, we
recommend testing the product first in an inconspicuous area
first to ensure compatibility - checking there is no deterioration in
the surface quality. Any cleaning products should be used as per
the manufacturers instructions.
If bleach is used to sanitise the product, it is important to rinse it
away with a copious amount of water. Bleach should not be left in
contact with the product for a long period of time.
Care should be taken to avoid contact with the following
chemicals as they can damage the gel coat; paint strippers,
strong disinfectants, alcohol, aftershave, perfumes, nail varnishes
and their removers.
If in doubt please contact DVS direct for further advice.
Step 3 : Wall Preparation & Drilling Template
Warranty
The Safe Ensuite Integrated Basin is guarenteed for 5 years from
purchase against defective material and assembly.
Support
For technical support please visit our technical pages on our
website at www.dartvalley.co.uk or contact us:
[e-mail]
[phone]
Head Office
Dart Valley Systems Ltd
Kemmings Close
Long Road
Paignton
Devon
TQ4 7TW
UK
Warranty & Support
*Not supplied
Install fittings as shown, ensuring the M12 threads are screwed
fully into the basin, and that the waste male iron adaptor must be
fully tightened to secure the waste grid firmly in position. Secure
basin with M12 nuts to 10 Nm.
IMPORTANT : The fixings on this basin must be tightened
to the recommended settings as per these instructions.
It is also important that they are not over tightened
Locating correct position
Please note - Maximum cable runs
Routing of plumbing for taps or spouts should be planned at this
stage.
Temporarily fix the drilling template at the desired height using
masking tape.
Drill through the marked areas on the template. Remove the
template, then secure the basin with the fixings as shown under
step.4 and 5.
NOTE : As a guide, UK guidelines recommend a distance
from the rim of the basin to the floor of between 780 and
800mm (standard use) / 720 and 740mm (disabled use).
Use rim line on the drilling template.
Waste pipe*
1¼”
Plastic
male iron
M12 AII thread
Waste grid
NOTE : The same ‘Typical Installation’ applies to all variants of
this basin. (NTH, 1TH L, 1TH R & 2TH)
When installing basins with tap holes, plumbing access will
need to be considered.
Typical Installation