Franke FCR 925 TC Operation manual

Instructions for use and installation
Cooker Hood
Istruzioni per l’uso e l’installazione
Cappa
Mode d’emploi et installation
Hotte de Cuisine
Bedienungsanleitung und Installation
Dunstabzugshaube
FCR 925 TC BK/XS CH
GB
IT
FR
DE

2
2
INDEX
SAFETY INFORMATION 3
CHARACTERISTICS 6
INSTALLATION 7
USE 10
MAINTENANCE 11
INDICE
INFORMAZIONI SULLA SICUREZZA 12
CARATTERISTICHE 15
INSTALLAZIONE 16
USO 19
MANUTENZIONE 20
SOMMAIRE
CONSIGNES DE SÉCURITÉ 21
CARACTERISTIQUES 24
INSTALLATION 25
UTILISATION 28
ENTRETIEN 29
IN ALTSVERZEIC NIS
SICHERHEITSINFORMATIONEN 30
CHARAKTERISTIKEN 33
MONTAGE 34
BEDIENUNG 37
WARTUNG 38
EN
IT
FR
DE

EN
3
3
SAFETY INFORMATION
For your safety and correct operation of the appliance, read this manual
carefully before installation and use Always keep these instructions
with the appliance even if you move or sell it Users must fully know the
operation and safety features of the appliance
The wire connection has to be done by specialized technician
•The manufacturer will not be held liable for any damages resulting from
incorrect or improper installation
•The minimum safety distance between the cooker top and the extractor
hood is 650 mm (some models can be installed at a lower height,
please refer to the paragraphs on working dimensions and installation)
•If the instructions for installation for the gas hob specify a greater
distance, this must be respected
•Check that the mains voltage corresponds to that indicated on the
rating plate fixed to the inside of the hood
•Means for disconnection must be incorporated in the fixed wiring in
accordance with the wiring rules
•For Class I appliances, check that the domestic power supply
guarantees adequate earthing
•Connect the extractor to the exhaust flue through a pipe of minimum
diameter 120 mm The route of the flue must be as short as possible
•Regulations concerning the discharge of air have to be fulfilled
•Do not connect the extractor hood to exhaust ducts carrying
combustion fumes (boilers, fireplaces, etc )

EN
4
4
•
If the extractor is used in conjunction with non-electrical appliances
(e g gas burning appliances), a sufficient degree of aeration must be
guaranteed in the room in order to prevent the backflow of exhaust gas
When the cooker hood is used in conjunction with appliances supplied
with energy other than electric, the negative pressure in the room must
not exceed 0,04 mbar to prevent fumes being drawn back into the room
by the cooker hood
•The air must not be discharged into a flue that is used for exhausting
fumes from appliances burning gas or other fuels
•If the supply cord is damaged, it must be replaced from the manufac-
turer or its service agent
•Connect the plug to a socket complying with current regulations, locat-
ed in an accessible place
•With regards to the technical and safety measures to be adopted for
fume discharging it is important to closely follow the regulations provid-
ed by the local authorities
WARNING: Before installing the Hood, remove the protective films
•Use only screws and small parts in support of the hood
WARNING: Failure to install the screws or fixing device in accordance
with these instructions may result in electrical hazards
•Do not look directly at the light through optical devices (binoculars,
magnifying glasses…)
•Do not flambè under the range hood; risk of fire
•This appliance can be used by children aged from 8 years and above
and persons with reduced physical, sensory or mental capabilities or
lack of experience and knowledge if they have been given supervision
or instruction concerning use of the appliance in a safe way and under-
stand the hazards involved Children shall not play with the appliance
Cleaning and user maintenance shall not be made by children without
supervision
•Children should be supervised to ensure that they do not play with the
appliance

EN
5
5
•
The appliance is not to be used by persons (including children) with re-
duced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
Accessible parts may become hot when used with cooking appliances
•Clean and/or replace the Filters after the specified time period (Fire
hazard) See paragraph Care and Cleaning
•There shall be adequate ventilation of the room when the range hood is
used at the same time as appliances burning gas or other fuels (not
applicable to appliances that only discharge the air back into the room)
•The symbol on the product or on its packaging indicates that this
product may not be treated as household waste Instead it shall be
handed over to the applicable collection point for the recycling of elec-
trical and electronic equipment By ensuring this product is disposed of
correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by
inappropriate waste handling of this product For more detailed infor-
mation about recycling of this product, please contact your local city of-
fice, your household waste disposal service or the shop where you pur-
chased the product

EN
6
6
C ARACTERISTICS
Dimensions
9
11b
Components
Ref. Q.ty Product Components
1 1 Hood Body, complete with: Controls, Light, Blower,
Filters
2 1 elescopic Chimney comprising:
2.1 1 Upper Section
2.2 1 Lower Section
9 1 Reducer Flange ø 150-120 mm
11b 2 Flap
15 1 Air Outlet Connection
Ref. Q.ty Installation Components
7.2.1 2 Upper Chimney Section Fixing Brackets
11 6 Wall Plugs
12a 6 Screws 4,2 x 44,4
12c 6 Screws 2,9 x 6,5
Q.ty Documentation
1 Instruction Manual

EN
7
7
INSTALLATION
Wall drilling and bracket fixing
Wall marking:
• Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the
centre of the area in which the hood will be installed.
• Draw a horizontal line at 650 mm above the hob. Place bracket 7.2.1 on the wall as shown
about 1-2 mm from the ceiling or upper limit aligning the centre (notch) with the vertical
reference line.
• Mark the wall at the centres of the holes in the bracket.
• Place bracket 7.2.1 on the wall as shown at X mm below the first bracket (X = height of the
upper
chimney section supplied), aligning the centre (notch) with the vertical line.
• Mark the wall at the centres of the holes in the bracket.
• Mark a reference point as indicated at 116 mm from the vertical reference line and 320 mm
above the horizontal reference line.
• Repeat this operation on the other side.
• Drill ø 8 mm holes at all the centre points marked.
• Insert the wall plugs 11 in the holes.
• Fix the brackets using the 12a (4,2 x 44,4) screws supplied.
• Insert the two screws 12a (4,2 x 44,4) supplied in the hood body fixing holes, leaving a gap
of 5-6 mm between the wall and the head of the screw.
11
12a
320 X
116
1÷2
116
650 min.
7.2.1

EN
8
8
Mounting the hood body
• Before attaching the hood body, tighten the two screws Vr located on
the hood body mounting points.
• Hook the hood body onto the screws 12a.
• Fully tighten support screws 12a.
• Adjust screws Vr to level the hood body.
• If necessary, it is possible to fasten the hood to the wall using more
screws with wall plugs, which can be positioned from inside the hood
canopy.
12a
Vr
Connections
AIR OUTLET DUCTING VERSION
When installing the Ducting version, join the Hood to the outlet
duct using a rigid or flexible pipe ø150 or 120 mm, selection of
which is at the discretion of the installation technician.
• Insert flaps 11b on the Hood Canopy Outlet.
Connecting the ø 150 pipe
• Fasten the pipe using suitable pipe clamps. The materials re-
quired to do so are not provided.
Connecting the ø 120 pipe
• To connect using a ø120 mm pipe, insert the reduction Flange
9onto the Hood Canopy Outlet.
• Fasten the pipe using suitable pipe clamps. The materials re-
quired to do so are not provided.
• In both cases, any Activated Charcoal Filters must be removed.
9
ø 120ø 150
AIR OUTLET – RECIRCULATION VERSION
• Unfasten the 2 screws fixing the upper bracket 7.2.1.
• Fasten the air outlet connector 15 in its place, using the 2
screws removed as above.
• Join the Connector 15 to the Hood canopy outlet using a rigid
or flexible pipe ø150 mm, selection of which is at the
discretion of the installation technician.
• Make sure that the Activated charcoal odour filter has been
fitted.

EN
9
9
ELECTRICAL CONNECTION
• Connect the hood to the mains through a two-pole switch hav-
ing a contact gap of at least 3 mm.
• Remove the grease filters (see paragraph Maintenance) being
sure that the connector of the feeding cable is correctly inserted
in the socket placed on the side of the fan.
Flue assembly
Upper exhaust flue
• Slightly widen the two sides of the upper flue and hook them
behind the brackets 7.2.1, making sure that they are well seat-
ed.
• Secure the sides to the brackets by using the 4 screws 12c (2,9
x 9,5) supplied.
• Make sure that the outlet of the extensions pieces is aligned
with the chimney outlets.
Lower exhaust flue
• Slightly widen the two sides of the flue and hook them be-
tween the upper flue and the wall, making sure that they are
well seated.
• Fix the lower part laterally to the hood body by using the 2
screws 12c (2,9 x 9,5) supplied.
12b

EN
1
0
10
USE
Control panel
T1 T2 T3 T4 L
Button Function
T1 Turns the Motor off.
T2 Turns the motor on at speed one Buttons T1+T2 are lit.
T3 Turns the Motor on at speed two Buttons T1+T3 are lit.
Press and hold for 2 seconds to activate
switch-off with a 30 minute delay (Mo-
tor+Lights). It is possible to change the oper-
ating speed with this function activated.
Buttons T1+ (T2 or T3 or
T4, respectively) flash.
T4 Turns the Motor on at speed three Buttons T1+T4 are lit.
Press and hold for 2 seconds to activate In-
tensive speed with a timer set to 6 minutes,
after which it returns to the speed that was
set previously. Suitable to deal with maxi-
mum levels of cooking fumes.
The Button flashes.
L Turns the Lighting system on and off at max-
imum intensity.
Button on