Freescale Semiconductor i.MX28 EVK User manual

Quick Start Guide for i.MX28 EVK
i.MX28 EVK
Multimedia and connectivity

The i.MX28 EVK is designed for
multimedia and connectivity applications.
These applications use the i.MX28 series
ARM9™ applications processor. The
i.MX28 EVK can be used as a hardware
and software development platform. This
decreases time to market and provides a
near-to-final product design. The board
support package (BSP) for the i.MX28
EVK contains drivers optimized for
multimedia operations using the i.MX28.
The following features are available
in the i.MX28 EVK board:
• i.MX28processor
• DoubleDataRate2(DDR2)
DRAMmemory
• DualUSBconnections
• Two10/100Ethernetconnections
• TwoSecureDigital(SD)/multimedia
card (MMC) connections
• Twoapplicationuniversalasynchronous
receiver/transmitters(UARTs)
• OneconsoleUART
• Twocontrollerareanetworks(CANs)
• AudioI/Ojacks
About the i.MX28 Board
This section provides information about the i.MX28 Kit Evaluation (EVK)
board and the location of the connectors and switches.

Quick Start Guide for i.MX28 EVK
Get to Know the i.MX28 Board
SD card slots on back side
Top view of the i.MX28 EVK board without the LCD module.
Wall 5V
power jack
Battery source
select switch
2.5 mm Li-ion
battery header
2 mm Li-ion
battery connector
LCD port connector
LRADC/touch
screen header
i.MX28 VDD5V supply
selection switch
Backlight
supply jumper
3.3V and 1.8V
regulator supply
jumper
JTAG connector
(20-pin standard)
JTAG reset switch
S/PDIF RCA
connector
Boot mode
select switch
HSADC header
NAND flash
daughter card
connector
Expansion port
connector
NAND flash
socket
Reset
button
Dual
Ethernet
RJ45
connector
Recovery
button
CAN dual
stack DB9
connector
Application
UART dual
stack DB9
connector
Debug
UART DB9
connector
Power
button
User
keys
Hold
switch
Headphone/
Line output
Line
Input
USB
host
jack
USB
OTG
jack
USB 5V
power
switch

Getting Started
This section describes how to use the i.MX28 Kit EVK and the
components in the EVK. This section also describes the PC requirements
to develop applications using the i.MX28 EVK.
Unpacking the Kit
The i.MX28 EVK is shipped with
the items listed in Table 1.
Ensure the items listed in Table 1 are
available in the i.MX28 development
kit. Remove the EVK board from the
antistatic bag and perform a visual
inspection.
Note:TheLCDModuleisanoptionaladd-onmodule
andisorderedseparately,MCIMX28LCD.
Web-Based Contents
Refer to freescale.com/
imx28evk for the latest i.MX28 EVK
documents and software.
Table 2 lists the documents available
on the Freescale web site.
i.MX28 EVK Development Kit Contents
Item Description
Board i.MX28 EVK board
SDCards
• Windows
®
Embedded CE
SDcard
• Linux
®
SDcard
Cables
• Ethernet straight cable
• USBcable(micro-Bto
standard-A)
Power Supply 5.0V/3.8Auniversal
power supply
Documentation
• End-userlicenseagreement
• QuickStartGuide
• Warrantycard
• Freescalesupportcard
DVD Gettingstartedvideotutorials
and useful web links
STEP
1
STEP
2
Table 1

Quick Start Guide for i.MX28 EVK
Web Site Contents
Type Requirement
EVKDocumentation
•Schematics,layout,andgerberfilesforEVKandLCDboard
•i.MX28EVKHardwareUser’sGuide
•i.MX28WindowsCEDemoImageReadme
•i.MX28WindowsCEQuickStartGuide(thisdocument)
•i.MX28WindowsCEReleaseNotes
•i.MX28WindowsCEUser’sGuide
•i.MX28WindowsCEReferenceManual
•i.MX28WindowsCEHelloWorldApplicationNote
•i.MX28LinuxDemoImageReadme
•i.MX28LinuxQuickStartGuide(thisdocument)
•i.MX28LinuxReleaseNotes
•i.MX28LinuxUser’sGuide
•i.MX28LinuxReferenceManual
•i.MX28LinuxHelloWorldApplicationNote
SoftwareDevelopmentTools •WindowsCESDKInstallationFile
•LinuxSDKInstallationFile
i.MX28EVKDemoImages CopyoftheOSimageprovidedontheSDcard—
LinuxdemoimageandWindowsdemoimage
Table 2

LCD Board Assembly
Connecting the LCD board to the i.MX28 EVK board
NOTE:
The4.3”widescreenvideographicsarray(WVGA)LCD
board is an optional card for the i.MX28 EVK board and
it is sold separately from the i.MX28 EVK board.
The i.MX28 EVK board is
connected to the add-on
LCDboardusing120-pin
surface mount connectors.
The connectors are
keyed to avoid incorrect
connection. Therefore,
there is only one way to
connect the boards. The
LCDboardisconnected
to the J78 connector. The
J78 connector is located
on the top of the i.MX28
EVK board as shown.

Quick Start Guide for i.MX28 EVK
J78 connector
for LCD. i.MX28
EVK board shown
without LCD

Connect RS232 Cable
ConnecttheRS232cabletothe
debugUARTport(optional).
Serialportconfiguration:115.2kbaud,
8databits,1stopbit,noparity.
Connect Power Supply
Connect the 5V power supply
cabletothe5VDCpowerjack(J84).
Power On
PressthePOWERbutton(S5).
Setting Up the Board
Check Jumpers
Ensurethejumpersandswitches
are in their default positions by comparing
themtothejumperandswitchsettings
tableinthisQuickStartGuide.
Insert SD Card
InserttheappropriateWindows
EmbeddedCEorLinuxSDcardinto
SDcardsocket0(onthebottomside
of the board).
Connect Ethernet Cable
Connect the Ethernet cable to
thelowerportoftheEthernetjack.
STEP
1
STEP
4
STEP
2STEP
5
STEP
6
STEP
3

Quick Start Guide for i.MX28 EVK
For WinCE:
1.Duringthebootprocess,therewillbe
operating system status information
scrolling on the terminal window of
the PC and the Freescale logo will
beshownonthe4.3”WVGAdisplay
daughtercard.
2. After the boot process completes,
calibrate the touch screen by pressing
the cross-hair targets.
3.TheWindowsCEGUIwillbenowbe
displayed.
4.ConnecttotheInternetviaInternet
Exploreroryourdefaultbrowser.
For Linux:
1.Duringthebootprocess,therewillbe
operating system status information
scrolling on the terminal window of the
PC and a penguin image in the upper
leftcornerofthe4.3”WVGAdisplay
daughter card.
2. After the boot process completes,
the Freescale login prompt will be
displayed on the terminal window and
theLinuxGUIwillbeshownonthe
4.3”WVGAdisplaydaughtercard.

i.MX28 EVK Board Jumper
and Switch Options
Reference
Designator Name Setting Description
S1 Battery source
select switch
BATT The battery source is a real Li-ion battery connected to either
J85 or J86.
*REG* The battery source is the EVK on-board 4.2V regulator.
S2 Boot mode
select switch
*B3* *B2* *B1* *B0*
*1* *0* *0* *1* The i.MX28 processor will boot from the i.MX28 SSP0 port,
which is SD card Socket 0.
- - - - For other boot mode switch settings, refer to the silkscreen table
on the EVK board.
S3 USB 5V power
switch
ON USB 5V power from the USB micro AB jack is connected to the
EVK board.
*OFF* USB 5V power from the USB micro AB jack is disconnected from
the EVK board.
S7 Hold switch
ON The user keys are locked.
*OFF* The user keys are unlocked.
Thefollowingisalistofallthejumperoptions.The*default*jumperandswitchsettingsareshownin
bold with asterisks.